RGambit Posted August 16, 2018 Share Posted August 16, 2018 (edited) Hi guys, I am looking for some advise regarding my new LL120 RGB fans. I am not sure if it is relevant but they are both replacing my Hidro100i v2 stock fans. Both are connected to the commander pro for power and to the LED hub for "color". - The fan on the top left is plugged into LED 1 (of hub) and fan on top right to the LED 2 - this shows that fan 1 is working but still awkward color. There is a section that is still blue with the marquee effect in red. Is this fan bad? - The fan on top right is plugged into LED 2 and is not working at all. If I switch to LED 1 still shows same behavior (spot blue light - no effects). picture of the fans (also attached): https://imgur.com/a/zaFylut If I swap their location in the hub none works (both present the blue spot light-no effects) Am I so unlucky and got both fans broken? Thank you all Edited August 16, 2018 by RGambit Link to comment Share on other sites More sharing options...
DevBiker Posted August 17, 2018 Share Posted August 17, 2018 What happens if you set both fans to be a completely solid color (say, green, for example)? Can you show us the profile setup screen for the lighting effects? Link to comment Share on other sites More sharing options...
RGambit Posted August 17, 2018 Author Share Posted August 17, 2018 Hi DevBiker I was hoping you would reply :) Before anything else: I got today the LL140 RGB which is plugged in LED1 instead of LL!120 (1) but not attached to the case just for testing. picture: LL140 - working perfectly (unfortunately don't have more fans to change positioning - this one will have to remain number 1 in the hub otherwise doesn't even work. tried swap to LED 2 or 3 with the LL120 before and doesn't even light up.) Color and fan scheme setup: pictures attached Result from that test: - picture 2 - (LED1-LL140 not shown) + LED 2 (LL120 LED1 from last post) + LED 3 (LL120 LED2 from last post) - basically the fans moved forward to give space to the new LL140. - picture 3 - (LED1-LL140 not shown) + swap LED2 with LED3 - both display the same blue dot light again. The fan number 2 from original post seems to be definitely busted. It seems to me that either a problem with the LED hub from position 2 or both fans are gone. Since I don't have any other fans working other than the LL140 i guess I'll never know 100% except if i return everything? hope is not very confusing. if it is I can try make it clearer Link to comment Share on other sites More sharing options...
Corsair Employee Corsair Jam Posted August 20, 2018 Corsair Employee Share Posted August 20, 2018 Hi RGambit! I wanted to see if you could test something. Could you possibly unhook all the LL fans and only hook up 1 fan at a time on the RGB Hub to see if the LEDs will work correctly? Link to comment Share on other sites More sharing options...
RGambit Posted August 20, 2018 Author Share Posted August 20, 2018 Hey, thank you all for trying to help. Please see attached pics of what happens if i plug each of the fans into position 1 of the hub only. pic 1- LL140 (works fine) pic 2 - LL120 (rainbow with blue spot..) pic 3 - other LL120 (blue spot only...) Tomorrow my LED hub and new LL120 replacement fans are arriving, hopefully will make a everything work Link to comment Share on other sites More sharing options...
DevBiker Posted August 21, 2018 Share Posted August 21, 2018 It sounds like it's not the fan hub but the fans themselves, likely both LL120's. :( 1 Link to comment Share on other sites More sharing options...
RGambit Posted August 21, 2018 Author Share Posted August 21, 2018 Everything working fine now with the 2 new LL120 fans. Thank you guys for helping :) Link to comment Share on other sites More sharing options...
RGambit Posted October 18, 2018 Author Share Posted October 18, 2018 Since you were so helpful with my previous issue, would you be so kind and check my post in this thread and see if you can help me? thank you http://forum.corsair.com/v3/showthread.php?t=172124 Link to comment Share on other sites More sharing options...
Pinhead17 Posted February 9, 2020 Share Posted February 9, 2020 I had the exact same problem with a single decorative fan in the back of my Corsair Obsidian Series 500D RGB SE Premium Mid-Tower Case. The fan always had a small round blue lit spot on it no matter what color configuration I did with iCue. I finally replaced the fan with a new one and NO BLUE SPOT! So It Is The FAN! Not the Commander Pro or the iCue software. Link to comment Share on other sites More sharing options...
Recommended Posts