- 260,970 Members
- 1,226,201 Posts
- 312 Online Now
Featured Posts
See all featured-
- 0
- 8
System Build InspirationStart Building with CORSAIR BUILD KITS
-
- 0
- 23
New Product ReleasesA Great Day for DIY – Introducing a Multitude of New Components
-
- 2
- 17
New Product ReleasesIntroducing the CORSAIR RMx SHIFT Series™ 80 PLUS Gold Fully Modular ATX Power Supplies
-
- 1
- 7
New Product ReleasesIntroducing the CORSAIR TC100 RELAXED Gaming Chair
-
- 0
- 1
New Product ReleasesLaunching the CORSAIR XENEON FLEX 45WQHD240 45-Inch OLED (3440x1440), 240Hz, Bendable UltraWide Gaming Display
Trending
Go to the forums-
iCUE v5.14.93 Release Notes
Bionic replied:
I did a clean installation in case something had failed during the update, but it still works the same if I activate a cooling profile and exit and close icue, it doesn't work, it only works when it is in the background, to avoid this I have to activate device memory mode
By Technobeard
Started39 -
Question about H115i RGB PRO XT fan sensors in iCUE
c-attack replied:
This is normal for Asus boards. You get a lot of junk values at the ends of the possible range (0C, 127C) as well as duplicates. The CPUID program CUE uses to fetch this data has a hard time with the Asus Embedded Controller and other programs like HWinfo will note this as well. This should not be possible because AC has no way to interact with CUE or the AIO fans. That lead from the AIO to CPU fan is just a tachometer wire. It reports a RPM to the motherboard to satisfy the built in 'boot safety' feature. There is no power or control wire and that was the "3 pin"/1 wire connector you mentioned earlier. The fans connect to the AIO fan splitter directly. No motherboard control there. The only way Armory Crate can interact with CUE is on the software level as both fight for access to the motherboard bus or other common access points. This is possible, but it doesn't come up much. I would continue with the support ticket. In your CUE settings gear, turn on "debug logging". The next time the fans give the bad readings, go back and export the logs. You must do this manually. Send it in with the ticket. There may be some clue about the error. What's bugging me a little is these software interaction issues typically affect a wide range of sensors. Coolant temp, pump rpm, and anything else in CUE. For it to specifically target the AIO fans each time while not affecting the pump or coolant temp value on the same device is not typical, so I still wonder if there is a hardware issue.
By AMLime
Started11 -
G1/4 thread spacing on Waterblock iCUE XC7 RGB ELITE LCD
Pascal74 replied:
yes, it's for a G 1/4 compression fitting with an external diameter of 24 mm. the 2 fittings can therefore be fitted if the centre distance is 27 mm on the waterblock. Many thanks for your reply. Yours faithfully
By Pascal74
Started5 -
ICUE Link or ICUE Issue
wriscolf replied:
I didnt do the registry. I did it now and it all works. Thanks
By wriscolf
Started4 -
Corsair One i500 Incoming!
Queeg replied:
Newegg has pulled the listing. I’m hoping there’s a 4090 option, otherwise it’s a no-go for me. I already have a 2000D case with a 4090 FE, and I see no reason to go backward in performance. And if the phantom Newegg listing is correct, the i500 will be only slightly smaller than the 2000D (and not really in the most important dimension).
By zguy85
Started4 -
Where is iCue Crash reports located?
c-attack replied:
C:Users/(name)/App Data (hidden)/Local/Corsair
By coldviper
Started2
