Abynsur

Hi I have a problem with one of the two corsair xd5 pumps. I have a completely corsair custom loop, last night I connect the second pump to the second commander pro but when I started the PC the pump didn't work, so I double-check all the cables and all were fine. I turn it on again and it doesn't work, so I unplug the pump in question from the commander pro and magically it starts spinning, but if I plug the cable back in it stops spinning. while the main pump runs quietly. can anyone tell me what it can depend on ??? it is as if they are going into conflict

i have a similar problem. I also have a second commander, where I attached 2 noctua f14 and one f12. the problem is that when the computer started, a noctua f14 made a small movement and then died. the second commander is not connected to a single sata but a sata which has multiple connections including ssd, i tried to change icue settings from auto to 4 pin nothing i tried to move the connector to another port from pc off and without power but nothing, I forced the update but nothing the fan stays still. then I try to disconnect and change the port from the pc on and the fan has started how can it be I can't understand the problem, if I turn off and start again the fan does not start could someone help me ??

i have a similar problem. I also have a second commander, where I attached 2 noctua f14 and one f12. the problem is that when the computer started, a noctua f14 made a small movement and then died. the second commander is not connected to a single sata but a sata which has multiple connections including ssd, i tried to change icue settings from auto to 4 pin nothing i tried to move the connector to another port from pc off and without power but nothing, I forced the update but nothing the fan stays still. then I try to disconnect and change the port from the pc on and the fan has started how can it be I can't understand the problem, if I turn off and start again the fan does not start could someone help me ??

hi i bought a second commander, i attached the aforementioned to the usb port and a sata power supply. here the problem when starting the PC the fan n3 does not show signs of life if the detachment is reattachment in another door works someone can explain to me why ???

then I hope it can be the solution for all those who have such a problem. yesterday I unplugged the commander and went to my friend's house to test it on his system, he too has installed programs such as hwinfo etc ..., I proceed to install the commander and connect all the cables, we turn on the system and go du ICUE , magically it works the sensor temperatures are normal. ok the commander is not broken so it is not his fault, today I go home for lunch and I make attempts by exclusion, using a second power supply and a bridge to start the power supply I try to power the commander externally by connecting it to my rog formula, and look a little the temperatures are normal, ok I disconnect everything and always with only one sensor connected I attach the commander to my 1200 watt rog thor power supply and it magically works. now tonight i will separate all cables and surely i already know that the problem is a source of em that was being transmitted i don't know how to commander

then, I turned off all the other programs but the problem remains so I tried the commander on a computer of a friend of mine and the sensors had very normal values ​​so I wonder what can it be ??? some setting of the rog formula x570 ?? because commander pro works he is not the problem

then, I turned off all the other programs but the problem remains so I tried the commander on a computer of a friend of mine and the sensors had very normal values ​​so I wonder what can it be ??? some setting of the rog formula x570 ?? because commander pro works he is not the problem

hello I also have your same problem, how did you solve it ???

same problem also me only that it worked for me two days ago and after changing motherboard and power supply with attached cable management. so I wonder if the problem may be that the cables are too attached to current sources ?? moreover, even the number one probe of the hydro x does not transmit correct data

Thank you very much for your kindness in replying. as per the suggestion I formatted the system, installed everything again but the temp problem on the sensors always the same problem 640 C ° more or less I honestly don't know where the problem lies

hi since yesterday, I have a problem with the commander pro and the ICUE software. after changing motherboard and power supply, I started the system, everything is fine except that the ICUE software gives values ​​of 640 C ° on the 4 sensors, but the temperature of my entire hydro x system (video card, processor and motherboard) temperatures are stable from 25 to 40 ° C. Has anyone happened to the same thing happen to him? furthermore, if I go to set the hydro x pump pre sets, the device does not respond and starts flashing. I tried to reset the commander pro it restarts I have to update and restart with the same sensor temperatures clearly wrong, I state that I have not formatted windows 10 after the motherboard change, can it be one of the problems? the cables are all connected perfectly the same way they were when the system was working perfectly. please someone give me a hand I don't know what to do. Thanks in advance to everyone