replicator

DevBiker, your an absolute star.

DevBiker would this work even though it has less wires in the header part as the Corsair one.

I too found a few but they do not seem to have the same amount of wires in the m/board connector side as the official Corsair cable ie 2x black into 1 pin 3x red into 1 pin and so on.

Hi, Can any forum members point me in the direction in obtaining one of these cables please within the UK, Corsair micro usb to m/board header from light node pro in the LL fan triple pack. Thank you

Linkup make 4.0 ones but not sure on the length for the above case/build.x570 board is pcie express 4.

Hi, Was looking for some valuable info on what Pcie gen 4.0 x 16 vertical graphics card cable/ribbon length/angle to use in my Corsair 1000d. It will for my Evga 2080 super with the Corsair xg7 water block on a Rog X570 crosshair formula board. Also ideal location as there are 2 vertical slots far left and the inc bracket to go on the main pci part also the power supply shroud has 2 stand offs. Any help would be app. Lots more questions to post on here in the next few days.😀

Cheers, its the rgb ext ones from the fan to make them longer.female to male.

LeDoyen You are a god, thank you for your help its much app.

Im in the uk so ebay . Does anyone have some links for 120 and 140mm LL fan PWM extensions and RGB extension cables please. Thank you

Thankyou LeDoyen for your response So i can not use the Aqua Computer Aquaero 5 PRO in my corsair 100d as there are no bay spaces any more in 99 percent of all new cases.so would have to sell that,i still have my Aquasuite software licence. so would i be able to use the aquaero 6 LT USB fan controller/or octo or both to fit the Aqua Computer Durchflusssensor high flow NEXT, OLED, 2x G1/4, RGBpx so i could get all my flow and temp readouts. my EK-Quantum Kinetic FLT 360 D5 PWM D-RGB - Plexi res/pump has a 3 pin argb 5v connector and molex for power plus a 4pin motherboard header.(cpu).would this work with the aquaero 6 LT or octo..or would i be able to connect/run it through corsair hardware and icue software. Not really bothered about the fans as corsair icue software will run these through the 2 commander pros. 6x rgb 6 way hubs and 6x lighting nodes. Any info would be greatly app. Thank you.

Hi Would app some help please. I have a Corsair 1000d case and 24 ll fans, plus 2 commander pros plus various nodes and rgb hubs all corsair.(came with all the fans). And Corsair Hydro X XG7 RGB GeForce RTX 2080 Graphics Card Water Block(with its little flow spinning thing) Due to cases not having dvd drive slots anymore im having to sell my Aquaero xt 5 fan/temp bay screen. I really need flow/temp/pump speed readouts,but everywhere online its one or the other. I just saw this Aqua Computer Durchflusssensor high flow NEXT, OLED, 2x G1/4, RGBpx and wondered if this could be used in my set up and how to connect it all using the above corsair or any other means to get it to work. Any help would be app. Thank you

What extension LL 120/140 Braided fan cables are you all running ,and where from please. pwm / argb Also anyone used or know of a good location to put the EK Quantum Kinetic FLT360 res/pump combo in the Corsair 1000D case as im starting my build in the next week or so. Thank you

What extension LL 120/140 Braided fan cables are you all running ,and where from please. pwm / argb Also anyone used or know of a good location to put the EK Quantum Kinetic FLT360 res/pump combo in the Corsair 1000D case as im starting my build in the next week or so. Thank you

Hi. Are there any forum members on here have any experience with EK-Quantum Kinetic FLT 360 D5 PWM D-RGB in a Corsair 1000D case position and fitting wise. I will be transferring over from current 900D build the Alphacool 480 ut60mm and the Alphacool 420mm ut60mm to the corsair and ive not seen a youtube vids of anyone fitting the ek flat res to the case insides and am wondering were to install it. Any help would be app.

Hi guys. I have just purchased a Corsair 1000D case to replace my outgoing 900D build, and have bought most of the items but could really do with some help and guidance plus links as to what is needed to get my 17 or so Corsair LL140 AND LL120 fans up and running with the right hardware. 1 x 480mm UT60 Rad 1 x 420mm UT60 Rad plus exhaust ie Number of Fan hubs for speed / Led / A-RGB Extenders Splitters A diagram for setup would be a great help. The 1000D has 1 x Commander pro My fans so far have.(MORE ON THE WAY). The double 140mm packs have 2 x light node pros and 2 x 6way rgb hubs The 120mm tripple packs have 2 x light node pos and 2 x 6 way rgb hubs. the other 4 x 140mm LLfans are single ones and do not include nodes or hubs. Could i ask how other forum members have wired everything up using splitters / extenders and aftermarket hubs along with corsairs to get up and running with the icue software please. Links to powered hubs /extenders/led/argb hubs and splitter cables would be really app. Also has any members on here used the EK quantum 360 Kinetic FLT res in 1000D,or used in connection with Corsair icue software,(will it pick it up so i can adjust the speed and view temp,or is it not compatible. I do not want to use the motherboard/bios to check all the time. i use my Aqua computer Aquaero and round res in my old 900D build at the mo. Any info/ help would be greatly app .

Thank you guys for your fast responses....much app, Any sugestions on the braided corsair fan extentions .

Could any forum members help with some info and possible links in setting up my 7 x LL140 and 8 x LL120 fans please ie number of .. Commander pros Rgb hubs Led hubs Splitter cables All above To work in icue software Poss cases 1000D Or thermaltake 900 showcase. Will be a custom loop with ek qiantum kinetic 360 flat res and pump. Any help would be app