marco964 Posted November 23, 2007 Share Posted November 23, 2007 During gaming or doing a few things at the same time the system crashes. I got a Asus P5N E SLI With 4G mem onboard the corsair CM2X1064-6400 manual memvolt 1,92 Got the timing 5-5-5-12-2 Advanced mem timings TRC 24 and rest auto. There is an option for linked / unlinked / auto its now on auto. Allready thnx for help Link to comment Share on other sites More sharing options...
DerekT Posted November 23, 2007 Share Posted November 23, 2007 The memory controller can not keep up with the extra DRAM at the rated 6400 speed. You will need to drop the speed of the DRAM from 800Mhz to 667Mhz. If you had purchased 4 X 1024MB of PC8500 (1066Mhz) DRAM, then you would have had to drop to PC6400 (800MHz) DRAM, etc. 2 X 2048 will not issue this problem. This is a problem of all 4 banks being populated. So, enter your BIOS Setup Utility and set your DRAM Bandwidth from 800Mhz to 667Mhz. ie. Advanced: JumperFree Configuration AI Tuning = Manual Overclock Options = Disabled System Clocks NB PCI-e Frequency (MHz) = 100 Voltage Control Vcore Voltage = Auto Memory Voltage = 2.0v NB Core Voltage = 1.393 FSB & Memory Config FSB - Memory Clock Mode = Unlinked FSB - Memory Ratio = 4:5 FSB (QDR) = 266 Chipset: Memory Timing Setting tCL = 5 tRCD = 5 tRP = 5 tRAS = 12 Command Per Clock = 2 Clocks tRRD = Auto tRC = Auto tWR = Auto tWTR = Auto tREF = Auto tRD = Auto tRFC = Auto Async Latency = Auto CPU Spread Spectrum = Auto PCIE Spread Spectrum = Auto SATA Spread Spectrum = Auto LDT Spread Spectrum = Auto LDT Frequency = 5x USB Configuration USB Controllers = Enabled USB Legacy Support = Disabled (Disable when you memtest. Enable afterwards if you have usb keyboard) USB 2.0 Controller = Enabled Download memtest from http://www.memtest.org and extract the ISO image. Burn the ISO image to an CD-ROM disk. Boot to the optical drive with the memtest disk and allow for two full passes. Results? Link to comment Share on other sites More sharing options...
marco964 Posted November 23, 2007 Author Share Posted November 23, 2007 Hi, Thnx but in unlinked i'm not able to set 4:5 and min FSB (QDR) is 533. regards. Link to comment Share on other sites More sharing options...
DerekT Posted November 24, 2007 Share Posted November 24, 2007 Set to 667Mhz. Link to comment Share on other sites More sharing options...
marco964 Posted November 24, 2007 Author Share Posted November 24, 2007 Hi have put fsb Mem on 667 and runs fine :biggrin:, i'm gonna try to fully load it and see what happens. Thnx for so far. Link to comment Share on other sites More sharing options...
DerekT Posted November 24, 2007 Share Posted November 24, 2007 Sure thing :) Work it hard and fast. Let us know if any issues arise. Link to comment Share on other sites More sharing options...
marco964 Posted November 26, 2007 Author Share Posted November 26, 2007 1. system stil works good without bsod, 2. but got a question is it true, that if you run 4 modules of 1 ghz and youre proc Q 6600 runs at 1066 mzh that its diveded by 2 that it runs max at 533 mzh at a slot, so you dont need memory at 800 mzh?? Link to comment Share on other sites More sharing options...
marco964 Posted November 28, 2007 Author Share Posted November 28, 2007 Today the system crashed 2ce and it was hard to start again. had to take the battery from the motherboard. Got an other question is it better to have 2 modules off 2ghz instead 4 off 1ghz? Otherwise i buy new ones i hate these crashes. And would you then recommend the twin2x2048 6400C4 pro?? Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted November 28, 2007 Corsair Employee Share Posted November 28, 2007 If you want 4 gig I would suggest Twin2x4096-6400C5DHX for that MB. Link to comment Share on other sites More sharing options...
marco964 Posted November 28, 2007 Author Share Posted November 28, 2007 Hey Ram, You sure twin and not quad? thnx again for quick reply Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted November 29, 2007 Corsair Employee Share Posted November 29, 2007 Yes its 2 2.0 Gig modules and would have the best performance over 4 modules. Link to comment Share on other sites More sharing options...
marco964 Posted December 19, 2007 Author Share Posted December 19, 2007 I try to find the twin, but i only could find the quad4096. Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted December 19, 2007 Corsair Employee Share Posted December 19, 2007 Newegg has them for 139.00 after rebate. Link to comment Share on other sites More sharing options...
Wired Posted December 19, 2007 Share Posted December 19, 2007 Damn, those were $20 more last week! And that's $139 BEFORE rebate ATM :) Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted December 20, 2007 Corsair Employee Share Posted December 20, 2007 I think it was after Rebate but I would need to look again, either way its a great price.:eek: Link to comment Share on other sites More sharing options...
bigbuck08 Posted December 20, 2007 Share Posted December 20, 2007 It is $99 after the $40 mail-in rebate. I just ordered them lol. :laughing: Link to comment Share on other sites More sharing options...
marco964 Posted December 20, 2007 Author Share Posted December 20, 2007 Its not possible to ship to holland :[pouts:. Anybody adres for holland?? Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted December 20, 2007 Corsair Employee Share Posted December 20, 2007 I am sorry I don't have any information about resellers out side the USA, but I would look for a Foreign version of Price Grabber or Price watch and see who might be selling them there. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.