KirakosovGeorgy Posted November 15, 2020 Share Posted November 15, 2020 Hello. Now I have H115i rgb platinum. At low revs, the pump crackles like a hard drive. At high revs, it is more like a high-frequency whistle. I would like to try h115i rgb pro xt or the new elite cappelix system. Which of these systems has the quietest pump? Link to comment Share on other sites More sharing options...
cavemankr Posted November 15, 2020 Share Posted November 15, 2020 both xt and elite cappelix use Coolit pump which is loud. I own the cappelix and it is loud as the pump spins at 2300 rpm at lowest setting. I also own the H150i Pro (non xt). this one is very quiet, inaudible from 2 feet away as the pump spins at 1100 RPM(quiet profile). the pump is Asetek Brand. I took out Cappelix because I couldnt stand the noise. Link to comment Share on other sites More sharing options...
c-attack Posted November 15, 2020 Share Posted November 15, 2020 The XT series will be identical to what you have now. The Platinum and XT lines share identical hardware, minus the internal lighting controller on the Platinum. The new Elite coolers are manufactured with the same partner, but I would not say it sounds exactly the same. My Elite is difficult to hear while holding it in my hands outside of the case on the low setting and the case fans at minimum cover it up. However, the Pro series from a few years back is the only one with an ultra low 1100 rpm "Quiet" pump speed. That is significantly lower than all other models, but of course there is no free lunch. It's great for quiet desktop work, but if you don't bump it up to the middle 2160 rpm speed, you will take a performance hit on extended load. The other models have more restrictive blocks and you can't get away with using half the pump speed. Link to comment Share on other sites More sharing options...
KirakosovGeorgy Posted November 15, 2020 Author Share Posted November 15, 2020 Thanks! Did I understand correctly that I won't hear any noticeable differences from my system? Please tell me, should my system (pump) crackle at low revs and produce high-frequency sound at maximum? I turned off the fans. Link to comment Share on other sites More sharing options...
LeDoyen Posted November 15, 2020 Share Posted November 15, 2020 the crackle is usually air bubbles passing through the pump. You'd want to make sure the pump is not the highest point of the loop. Even if your radiator is front mounted with tubes on top, as long as the top of the radiator is higher than the pump, it should be okay. What i usually do with new AIOs is run them at full speed constantly for a few days to force the air into the top tank of the radiator. after a while, the crackling usually goes away. Link to comment Share on other sites More sharing options...
c-attack Posted November 15, 2020 Share Posted November 15, 2020 What you are describing has been a common user complaint for the Platinum/XT models. Others have described the Quiet setting in the same manner and they actually prefer to use the medium setting. Even though it is technically louder, it is a smoother sound. It's hard to say why, but the original specifications for the Platinum did not include that lowest speed. It was added via firmware update later on. The Elite coolers are made with the same partner, but the components are not the same. Noise is highly subjective. If the case sits on desk, 18 inches from your ear and you prefer to keep your case fans off, you are going to hear something. Pump, HDDs, whatever is left. If you can hear the "H115i Pro" at 1100 rpm, you should take your head out of the case. The entire model line was designed to be quiet with lower max speed versions of the ML fans. It was a direct response to criticism about the prior model being too noisy out of the box. It is capable of using any PWM fan you like and of course the pump can be set to higher speeds when performance is required. I still have mine and it was an excellent cooler. Link to comment Share on other sites More sharing options...
KirakosovGeorgy Posted November 15, 2020 Author Share Posted November 15, 2020 (edited) I have 115 platinum I installed the radiator at the top of the case. The pump was running at maximum speed all the time. Now I have set the minimum mode. After a few hours, she began to work quieter. I don't understand why the air bubbles did not come out earlier at maximum speed? Edited November 15, 2020 by KirakosovGeorgy Link to comment Share on other sites More sharing options...
LeDoyen Posted November 16, 2020 Share Posted November 16, 2020 well AIOs have tiny wee pumps. even at full speed it's not earth shattering. they need time to work the bubbles out and bleed them to the top of the loop. Same thing on custom loop, despite the more powerful pumps. takes days to have all the bubbles purged, but it happens. Link to comment Share on other sites More sharing options...
KirakosovGeorgy Posted November 17, 2020 Author Share Posted November 17, 2020 Thanks guys! Link to comment Share on other sites More sharing options...
Recommended Posts