Corsair GregX

RMx SHIFT does fit Lian Li 216, there is enough clearance for flat cables that RMx SHIFT has. Here is also a user from Reddit that confirmed he was able to fit it ->

@tzerony 329mm GPU will work in your situation, barely though (will touch fans). 4000D case has an internal length of 392mm. If you subtract 38mm for radiator and 25mm for fan (dimensions as from Arctic LF II 360mm spec).

You can install GPU up to 329mm in length. For your AIO, I believe radiator is 38mm and fan is 25mm.

There will be support for 4070 and 4070 Ti with the upcoming XG3 RGB HYBRID GPU BLOCK.

Hi @dragoneti @c-attack @KapitainKavern Hydro X Series XC7 RGB CPU Water Block (115X/AM4), SKU CX-9010004-WW and CX-9010005-WW - first revision blocks with '115X' in the name have its own backplate for AM4 installation and will not work with AM5. Later CPU water block models Hydro X Series XC7 RGB CPU Water Block (1200/AM4) - with '1200' in the name and XC7 RGB PRO will work with AMD AM5.

Hi! The best usage for this port is for the temperature probe. It can also work as a drain but the bottom two ports are better for drain (are dedicated drain ports).

All pre-installed pads on this block are 1mm thick.

1000W+ for your configuration. Check PSU finder for a list of compatible / recommended options. https://www.corsair.com/pc-builder/psu-finder

Yes, there will be enough clearance with a top mounted 240mm AIO.

One is more than enough.

There is enough room for RMx Shift in H7 and H710. For anyone that is wondering about compatibility with their case, you can try the CORSAIR PC Builder or the PSU finder, both are updated with RMx Shift case compatibility data.

Hi, Yes, RMx SHIFT works with NZXT H9 Flow. Side mount with cables on top of the PSU.

These are adapters and are used with fittings. Compatibility wise, these are not related with your choice of tubing. Fittings should be compatible with your soft line tubing. If you have Corsair XT Softline 10/13mm tubing, you need XF Compression 10/13mm (3/8” / 1/2”) ID/OD Fitting. https://www.corsair.com/Categories/Products/Custom-Cooling/Fittings/hydro-x-compression-config/p/CX-9051002-WW

Hi, very nice to hear about fast delivery! Thermal pad thickness for memory IC. Original - 1mm XG7 4090 STRIX/TUF - 1mm For the backplate, thermal pads are not required. Runs like a champ!

You can be rest assured, Hydro X Series XG7 RGB 40-SERIES GPU Water Block (4090 SUPRIM/TRIO) will match all cards that are currently listed as compatible. Unfortunately, availability has been pushed to February. For notification on the actual availability please use the 'NOTIFY ME WHEN IN STOCK" option. https://www.corsair.com/Categories/Products/Custom-Cooling/Blocks/GPU-Blocks/Hydro-X-Series-XG7-RGB-40-SERIES-GPU-Water-Block/p/CX-9020021-WW

@LeDoyen For the GPU model, I referred to information from his configuration pdf where 3080 Ti FE is selected. For 3060 Ti FE, sadly no full cover GPU solution from our end.

If you switch top radiator from 280mm to 360mm you will need to accomodate fan selection. Remove 2x 140mm fans and add 3x 120mm fans. You can simply remove GPU water block from your list. Keep amount of fittings the same as on the list. But sincerely, why don't you want to use GPU block? Water cooled GPU is the sweetest part of custom cooling.

Yes, you can do that, you will be able to fit XR5 420 on front and XR5 360 on top.

Dimensions of complete assembly ASUS 4090 STRIX/TUF PCB + water block. 234mm long, 170mm wide. You will be able to install it horizontally in Lian Li Dynamic Evo.

Yes, in 4000 series case you will be able to fit the 240mm radiator on top with no impact on memory height clearance.

Hi Marcus, If the Custom Cooling Configurator offers only the XD3 pump, it means that your graphics card is so long that disables option for XD5 pump. In 500D RGB SE, XD5 can be mounted onto front radiator where it interferes with long graphics card models. One possibility to use XD5 pump would be to vertically mount your graphics card (using vertical mount placement in 500D RGB SE). This way graphics card is moved towards the side so there is enough clearance to install XD5 pump. I would opt for this solution only if you will water cool your graphics card. With stock cooling on your graphics card, it's very likely that it will not be possible to fit it or it will have reduced cooling due to glass panel which will choke stock cooling solution.

Yes, you will be able to put a 360mm radiator in side tray and a 360mm on top. For more information about possibilities, I would suggest trying the CORSAIR Custom Cooling Configurator.

Hi! Hydro X Series XC7 RGB CPU Water Block (1200/AM4) is out-of-the-box compatible with AM5.

I don't think it will be required to remove the cable bar, also depends on the motherboard used as E-ATX can vary in width. It would be best to ping over on https://discord.gg/corsaircaseownersclub, I'm sure there was someone with the same question.

Hi, For now, confirmed is a block for the NVIDIA RTX 4090 Founders Edition. The Hydro X Series XG7 4090 FE total-conversion waterblock will be available in November 2022 https://www.corsair.com/newsroom/press-release/ready-to-go-beyond-fast-corsair-announces-compatibility-for-nvidia-40-series-graphics-cards