corsdd Posted June 3, 2011 Share Posted June 3, 2011 Pls sorry for my bad english! I have a problem with my Corsair SSD... I use Linux ubuntu os. SMART Info: === START OF INFORMATION SECTION === Model Family: SandForce Driven SSDs Device Model: Corsair CSSD-F60GB2 Serial Number: Firmware Version: 1.1 User Capacity: 60,022,480,896 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 6 Local Time is: Fri Jun 3 17:11:08 2011 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7f) SMART execute Offline immediate. Auto Offline data collection on/off support. Abort Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 48) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 116 114 --- Pre-fail Always - 0/138702457 5 Retired_Block_Count 0x0033 091 091 --- Pre-fail Always - 768 9 Power_On_Hours_and_Msec 0x0032 100 100 --- Old_age Always - 1h+51m+29.630s 12 Power_Cycle_Count 0x0032 100 100 --- Old_age Always - 13 171 Program_Fail_Count 0x0000 000 000 --- Old_age Offline - 0 172 Erase_Fail_Count 0x0000 000 000 --- Old_age Offline - 0 174 Unexpect_Power_Loss_Ct 0x0030 000 000 --- Old_age Offline - 12 177 Wear_Range_Delta 0x0000 000 000 --- Old_age Offline - 0 181 Program_Fail_Count 0x0000 000 000 --- Old_age Offline - 0 182 Erase_Fail_Count 0x0000 000 000 --- Old_age Offline - 0 187 Reported_Uncorrect 0x0032 100 100 --- Old_age Always - 0 194 Temperature_Celsius 0x0022 031 042 --- Old_age Always - 31 (Min/Max 0/42) 195 ECC_Uncorr_Error_Count 0x001c 116 114 --- Old_age Offline - 0/138702457 196 Reallocated_Event_Count 0x0033 100 100 --- Pre-fail Always - 0 231 SSD_Life_Left 0x0013 087 087 --- Pre-fail Always - 1 233 SandForce_Internal 0x0000 000 000 --- Old_age Offline - 0 234 SandForce_Internal 0x0000 000 000 --- Old_age Offline - 0 241 Lifetime_Writes_GiB 0x0032 000 000 --- Old_age Always - 0 242 Lifetime_Reads_GiB 0x0032 000 000 --- Old_age Always - 128 Error SMART Error Log Read failed: Input/output error Smartctl: SMART Error Log Read Failed Error SMART Error Self-Test Log Read failed: Input/output error Smartctl: SMART Self Test Log Read Failed Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. if i exec the command cat /dev/sdc (partition table not present after the problem) the terminal does not display output. command dmesg not display I/O Error..... how do I rescue and copy my data? pls help me. Link to comment Share on other sites More sharing options...
corsdd Posted June 5, 2011 Author Share Posted June 5, 2011 pls help me... the rescue with testdisk or other utility not work looking with a hex editor inside the disk all the data have value 0x00! In addition, the diskis not recognized from utility for flashing the firmware. Crystal disk info output: Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted June 7, 2011 Corsair Employee Share Posted June 7, 2011 I do apologize but we have no suggestions on how you could recover data from your SSD. Best thing we can do is have the drive replaced, which can be done on the left side. Link to comment Share on other sites More sharing options...
corsdd Posted June 8, 2011 Author Share Posted June 8, 2011 I've isolated the problem. I've used ssd with Icy Box enclosure via e-sata without problems from when I bought ssd. Some days ago I turn off pc and I've forgot to turn off external enclosure, and ssd was left electrically turned on all night long. The day after, when I power up pc, ssd was cleared. And I made the 1st post. After, I've put ssd into pc and I've upgraded firmware to 2.0, and I've reinstalled O.S. but today when I've turned on pc it was erased again. I premise that when turn off pc, I don't remove electricity and MB was still powered. At this point I think there're problem with ssd.. What do you think? Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted June 8, 2011 Corsair Employee Share Posted June 8, 2011 I would agree and best to have the drive replaced, which can be done on the left menu bar. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.