ExoD Posted March 23, 2010 Share Posted March 23, 2010 I have been experiencing . -unexpected_kernel_mode_trap -page_fault_in_nonpaged_area -memory_management -irql_not_less_or_equal -cache_manager -bad_pool_header These are my current bios settings below. I have ran memtest on all sticks 1 at a time. They all tested good. I just installed Windows 7 updated it to current then installed all updated drivers. After i change settings in bios it will run ok for a day then start acting up after that. I tryed just running two sticks of mem in channel B but no dice it did the same as when all 4 sticks are in. HELP!! Im at the end of my rope with this system its been one thing after another. HELP!!!! MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster ...............: Auto CPU Clock Ratio ..........................: 10x CPU Frequency ...........................: 2.66 (266x10) Clock Chip Control Standard Clock Control CPU Host Clock Control..................: [Enabled] CPU Host Frequency (Mhz) ............: 266 PCI Express Frequency (Mhz) .........: 100 C.I.A.2 .................................:[Disabled] Advanced Clock Control [Press Enter] CPU Clock Drive...........................: 700Mv PCI Express Clock Drive.................: 700mV CPU Clock Skew (ps)....................: 0 MCH Clock Skew (ps)...................: 0 DRAM Performance Control Performance Enhance...................: [sTANDARD] Extreme Memory Profile (X.M.P.).....: [Disabled] (G)MCH Frequency Latch...............: [266 MHz] System Memory Multiplier ..............: 3.00A Memory Frequency (Mhz) ..............: 800 DRAM Timing Selectable ................: [Manual] Standard Timing Control CAS Latency Time........................5 tRCD .........................................5 tRP'...........................................5 tRAS..........................................15 Advanced Timing Control tRRD...........................................4 tWTR..........................................4 tWR............................................8 tRFC...........................................68 tRTP...........................................4 Command Rate (CMD) ....................:0 [AUTO] Channel A Static tRead Value.........................:Auto 7 tRD Phase0 Adjustment...................:Auto 0 tRD Phase1 Adjustment...................:Auto 0 tRD Phase2 Adjustment .................:Auto 0 tRD Phase3 Adjustment..................:Auto 0 Trd2rd(Different Rank)....................: 6 Twr2wr(Different Rank)...................: 6 Twr2rd(Different Rank)...................: 5 Trd2wr(Same/Diff Rank)..................: 8 Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps DDR Write Training..........................:Auto Channel B Static tRead Value.........................:Auto 7 tRD Phase0 Adjustment...................:Auto 0 tRD Phase1 Adjustment...................:Auto 0 tRD Phase2 Adjustment .................:Auto 0 tRD Phase3 Adjustment..................:Auto 0 Trd2rd(Different Rank)....................: 6 Twr2wr(Different Rank)...................: 6 Twr2rd(Different Rank)...................: 5 Trd2wr(Same/Diff Rank)..................: 8 Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps DDR Write Training..........................:Auto Motherboard Voltage Control CPU CPU Vcore….……….........................:Auto (1.33750) CPU Termination…..... 1.200V*.......: Auto (1.2) CPU PLL…………………....1.500V*.......: Auto (1.5) CPU Reference.…………....0.755V*.......: Auto (0.760) MCH/ICH MCH Core…………….....1.100V...........: 1.3 MCH Reference….…….0.800V...........; Auto (0.760) MCH/DRAM Ref.…......0.900V...........: Auto (0.900) ICH I/O……………….....1.500V............: Auto (1.500) ICH Core…………...……1.100V............: Auto (1.100) DRAM DRAM Voltage ……....1.800V............: 2.200 DRAM Termination .…0.900V............: Auto (0.900) Channel A Reference 0.900V............: Auto (0.900) Channel B Reference 0.900V............: Auto (0.900) Advanced Settings Limit CPUID Max. to 3.....................: [Disabled] No-Execute Memory Protect............: [Enabled] CPU Enhanced Halt (C1E)................: [Disabled] CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.........................: [Disabled] Virtualization Technology................: [Disabled] Integrated Peripherals USB Keyboard..................................[Enabled] USB Mouse......................................[Enabled] USB Storage....................................[Enabled] Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted March 24, 2010 Corsair Employee Share Posted March 24, 2010 What are some of the stop codes you have received when you get the blue screens? They should help narrow down the issue. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.