silentscrewball Posted January 8, 2020 Share Posted January 8, 2020 After installing this update my system is still bugged from the last update. It will change to another lighting profile by itself, then I can't use my keyboard or icue to change profiles until I completely close down and restart icue. Really annoying and I didn't have any problems with icue until the 3.23 update. Link to comment Share on other sites More sharing options...
R4D1C4L_FL1GHT Posted January 8, 2020 Share Posted January 8, 2020 Still got the issue with Ironclaw wireless losing ICUE profile :( also do we know when slipstream (multiple devices for one dongle) is being added outside of the beta? Link to comment Share on other sites More sharing options...
swarfega Posted January 8, 2020 Share Posted January 8, 2020 Still have the problem of my Commander Pro being detected as a Hydro X. Link to comment Share on other sites More sharing options...
BlaiseP Posted January 8, 2020 Share Posted January 8, 2020 Still have the problem of my Commander Pro being detected as a Hydro X. Run the Hydro X setup, say "No" and it'll go away. Otherwise, put your thermal probe into a port other than port 1. Link to comment Share on other sites More sharing options...
mgrenier25 Posted January 9, 2020 Share Posted January 9, 2020 So I don't know if this is related to last update but my Ironclaw mouse will not work anymore with my usb hub, and my Steam overlay is having some serious issues as well. Link to comment Share on other sites More sharing options...
Gypsycurse Posted January 9, 2020 Share Posted January 9, 2020 Is anyone else having issues with ST100 stand constantly losing the lighting profile? I can close and reopen the iCue app but each time within around 3-5 minutes the lighting reverts to default rainbow effect. John Link to comment Share on other sites More sharing options...
swarfega Posted January 9, 2020 Share Posted January 9, 2020 Run the Hydro X setup, say "No" and it'll go away. Otherwise, put your thermal probe into a port other than port 1. If you mean run the wizard in settings, it goes straight to asking which fan is connected to the Hydro X, of course none of them are. I also have a problem in each temperature connector. Link to comment Share on other sites More sharing options...
SCO77YBOY Posted January 9, 2020 Share Posted January 9, 2020 Hi everyone, Here are the official patch notes for iCUE v3.24.52: iCUE v3.24.52 Patch Notes:: Added support for K95 RGB PLATINUM XT and ICUE H100i/H115i/H150i PRO XT Liquid CPU Coolers iCUE now supports Elgato Stream Deck G-Key Integration with K95 RGB PLATINUM/XT keyboards. To use this feature, please ensure you have SDK Enabled in settings and using the latest version of Stream Deck (v4.5): https://www.elgato.com/en/gaming/downloads This allows G1-G6 keys to be assignable through Elgato’s Stream Deck software and works simultaneously with any Actions assigned in iCUE. For more information, please see our tutorial here: Resolved an issue with iCUE macOS not launching the calculator as an Action Resolved an issue with K66 showing lighting when it is not actually supported Resolved an issue that caused Actions in the Action Library to play over ESC and F-Keys Resolved an issue with Virtuoso headsets improperly displaying battery status when charging cable is rapidly plugged and unplugged with a USB cable Resolved an issue firmware progress counter in iCUE space being incorrectly displayed Resolved an issue with performance curve objects being incorrectly displayed Resolved other various minor bugs and issues Please also note that motherboard integration is now in beta. For more information, here is the link to the subforum which includes steps on how to install it: https://forum.corsair.com/v3/forumdisplay.php?f=311 installed latest icue software , installed elgato software so i could use with my k95 ,elgato doesn't pick up my icue software ( it just says icue not running ) 1hr later , uninstalled elgato. lol also my h100i platinum doesn't light up with sdk games , it has been like this since the day i bought it. 7 months ago Link to comment Share on other sites More sharing options...
BlaiseP Posted January 9, 2020 Share Posted January 9, 2020 If you mean run the wizard in settings, it goes straight to asking which fan is connected to the Hydro X, of course none of them are. I also have a problem in each temperature connector. That's how CorsairGreg explained it worked (the wizard) and moving my probe off thermal port 1 prevented my setup from detection I had a Hydro X setup. Link to comment Share on other sites More sharing options...
swarfega Posted January 9, 2020 Share Posted January 9, 2020 Thing is though, I have both probes in. Link to comment Share on other sites More sharing options...
makaveli6103 Posted January 9, 2020 Share Posted January 9, 2020 I also noticed new firmware 1.02.64 for Vengeance RGB PRO RAM and enabling Full Software Control for it doesn't use a crazy amount of CPU anymore. Mine still uses a lot of CPU. Should I uninstall and reinstall? Did you just upgrade? Link to comment Share on other sites More sharing options...
BlaiseP Posted January 9, 2020 Share Posted January 9, 2020 Thing is though, I have both probes in. There are 4 ports for thermal probes on a Commander Pro, that leaves 3 ports to choose from (using the assumption that if something is plugged into port 1 that ICUE believes you might have a Hydro X setup). I have 2 x Commander Pro's and use a Phoyba inline 10kΩ water temperature sensor on each as a source for my fan curves. All I did was moves my probes to port 2 on the Commander Pro's and I was no longer prompted with the "Hydro X detected" button that would launch the wizard. Link to comment Share on other sites More sharing options...
BlaiseP Posted January 9, 2020 Share Posted January 9, 2020 Mine still uses a lot of CPU. Should I uninstall and reinstall? Did you just upgrade? I only upgraded (not reinstalled ICUE) and did the RAM firmware update. With full software control for the RAM, I sit between 1~2% CPU usage on my 9900k with 5 layers of lighting effects for the RAM. If you are seeing a lot of CPU usage, you could try a full uninstall/reinstall of v3.24.52 to see if the usage drops (couldn't hurt). Link to comment Share on other sites More sharing options...
swarfega Posted January 9, 2020 Share Posted January 9, 2020 There are 4 ports for thermal probes on a Commander Pro, that leaves 3 ports to choose from (using the assumption that if something is plugged into port 1 that ICUE believes you might have a Hydro X setup). I have 2 x Commander Pro's and use a Phoyba inline 10kΩ water temperature sensor on each as a source for my fan curves. All I did was moves my probes to port 2 on the Commander Pro's and I was no longer prompted with the "Hydro X detected" button that would launch the wizard. Thanks for the advice, I will give this a go tomorrow. Link to comment Share on other sites More sharing options...
Zubing Posted January 10, 2020 Share Posted January 10, 2020 are there any fixes for the Ironclaw Wireless connection issue? Here is the page about this issue + more detail - https://forum.corsair.com/v3/showthread.php?t=191932 Link to comment Share on other sites More sharing options...
Mussels Posted January 10, 2020 Share Posted January 10, 2020 Amazing update for me 1. CPU usage fixed for Vengeance RGB pro ram 2. Ryzen CPU now idles correctly!! (2700x, in my case) 3. Asus motherboard support (including seperate settings per area/for light strips... amazing) Link to comment Share on other sites More sharing options...
A Computer Guy Posted January 10, 2020 Share Posted January 10, 2020 With this new version iCue seems more stable and haven't had any crashes with my USB audio today. Link to comment Share on other sites More sharing options...
A Computer Guy Posted January 10, 2020 Share Posted January 10, 2020 Is anyone else having issues with ST100 stand constantly losing the lighting profile? I can close and reopen the iCue app but each time within around 3-5 minutes the lighting reverts to default rainbow effect. John My profile seems to stick but after I turn my PC off I have noticed one day the ST100 default rainbow effect was on even when my PC was off. That's happened with my Strafe RGB MK.2 keyboard occasionally as well. Link to comment Share on other sites More sharing options...
swarfega Posted January 10, 2020 Share Posted January 10, 2020 I only upgraded (not reinstalled ICUE) and did the RAM firmware update. With full software control for the RAM, I sit between 1~2% CPU usage on my 9900k with 5 layers of lighting effects for the RAM. If you are seeing a lot of CPU usage, you could try a full uninstall/reinstall of v3.24.52 to see if the usage drops (couldn't hurt). I swapped the probes from 1 and 2 to 3 and 4 and it fixed the issue. Link to comment Share on other sites More sharing options...
makaveli6103 Posted January 10, 2020 Share Posted January 10, 2020 Mine still uses a lot of CPU. Should I uninstall and reinstall? Did you just upgrade? Nevermind. Did not upgrade the RAM firmware. Now uses very little CPU. Link to comment Share on other sites More sharing options...
OD RESET Posted January 11, 2020 Share Posted January 11, 2020 (edited) I just woke my PC up from sleep and the iCUE v3.24.52 software is detecting 2 different instances of the H100i v2 cooler. Quitting and the application via the notification overflow area on the Windows task-bar and then reopening the software doesn't resolve this issue. (Attached are photos with 2 instances of the cooler) -Edit: Only logging out or a restart of the computer resolves the problem. Even after of which the cooler is recognized as H100i v2 (1) . Will doing a repair of the program remove any keyboard profiles or custom cooler profiles? I'd like to try and fix this issue without attempting to start from scratch and risk losing everything. -Edit 2: I performed a repair and will report back if the issue persists Edited January 11, 2020 by OD RESET Link to comment Share on other sites More sharing options...
Azza1 Posted January 11, 2020 Share Posted January 11, 2020 Corsair Ironclaw wireless users steer clear of this update. I had the same problem with a previous update where my mouse in wireless mode keeps switching to its stock DPI, and the profiles I delete turn up again. This issue really needs to be resolved as there seems to be no solution but to downgrade icue. Link to comment Share on other sites More sharing options...
Azza1 Posted January 12, 2020 Share Posted January 12, 2020 are there any fixes for the Ironclaw Wireless connection issue? Here is the page about this issue + more detail - https://forum.corsair.com/v3/showthread.php?t=191932 No fix as of late, do NOT update to this firmware if you own an ironclaw wireless. Stick to the current stable firmware v3.21.88 and do not update mouse and dongle firmware. Still no response from Corsair after this issue has been present for months! Rather concerning that this is taking so long. Link to comment Share on other sites More sharing options...
Mussels Posted January 12, 2020 Share Posted January 12, 2020 I must have lost my post or made it in the wrong spot: My vengeance pro RGB ram is now stuck on a red triangle, the only thing that fixes it is completely disconnecting the PC from the wall. Red triangle again on next restart or shutdown. Lighting is frozen on a red/yellow/orange combo while this is occuring Link to comment Share on other sites More sharing options...
BlaiseP Posted January 12, 2020 Share Posted January 12, 2020 I must have lost my post or made it in the wrong spot: My vengeance pro RGB ram is now stuck on a red triangle, the only thing that fixes it is completely disconnecting the PC from the wall. Red triangle again on next restart or shutdown. Lighting is frozen on a red/yellow/orange combo while this is occuring Do you have SPD Write enabled for your RAM in the UEFI/BIOS? This is a feature on most Intel boards but I'm unsure what the equivalent in the UEFI/BIOS is for AMD (or is it the same?). Link to comment Share on other sites More sharing options...
Recommended Posts