The Corsair User Forums  

Go Back   The Corsair User Forums > Corsair Product Discussion > Hydro X Custom Cooling

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
  #1  
Old 01-09-2020, 03:09 PM
Kylian Kylian is offline
Registered User
 
Join Date: Jan 2020
Posts: 4
POST ID # = 1030679
Kylian Reputation: 10
Default Bruit h100i RGB platinium

Bonjour,
j'ai récemment reçus un WaterCooling h100i RGB platinium de chez corsair, je l'ai installer puis tester, il à l'air de marcher pour le peut que j'ai allumer mon PC, mais il fait un bruit de grésillement assez dérangent en mode équilibrer et en mode extrême, puis de temps en temps, quelques secondes en mode silencieux, je voudrais savoir si cela est normal on pas ??
Voila une vidéo que j'ai faite :
Edit: C'est la première fois que j'installe un WC donc j'ai rien toucher niveaux paramètre dans le BIOS ou dans ICUE

Merci d'avance.

Last edited by Kylian; 01-10-2020 at 02:16 AM.
Reply With Quote
  #2  
Old 01-09-2020, 05:27 PM
mgrenier25 mgrenier25 is offline
Registered User
mgrenier25's PC Specs
 
Join Date: Jan 2020
Posts: 11
POST ID # = 1030701
mgrenier25 Reputation: 10
Default

J'pense que les chances que quelqu'un te réponde en francais sont minces.
Reply With Quote
  #3  
Old 01-10-2020, 02:17 AM
Kylian Kylian is offline
Registered User
 
Join Date: Jan 2020
Posts: 4
POST ID # = 1030758
Kylian Reputation: 10
Default

Je vais en refaire un en anglais je pense
Reply With Quote
  #4  
Old 01-10-2020, 09:18 PM
c-attack c-attack is offline
Registered User
c-attack's PC Specs
 
Join Date: Jun 2014
Posts: 10,098
POST ID # = 1030888
c-attack c-attack Reputation: 107
Default

We can all translate it, but what usually ends up happening is the thread gets moved the relevant language specific section and some one complains about the responses in English. Also, since this was posted in Custom Cooling Section (Hydro X) and not the AIO cooling section, I am sure everyone expected it to be moved.

It sounds like pretty standard air bubbles to me. It happens sometimes when the package gets shaken a bit in transit or even just doing the installation, turning it over and over trying to figure out the best way to make it fit. The bubbles are small and make static-like pops as they are forced about the CPU block.

The easiest solution is to lift the front of the case up, in order to raise the inlet/outlet tubes above the CPU block. The bubbles leave the block area and the noise stops. Unfortunately, it is not always so easy in practice. You will see others suggest tipping the case over on its side, but this is usually easier and it should take minutes and not hours to lead the bubbles elsewhere. You may have to fiddle a bit with the angles. If you hear the noise stop or decrease when you lift, you know you are on the right track. A mechanical issue would not care about pump orientation or angle and will sound terrible all the time.
Reply With Quote
  #5  
Old 01-11-2020, 08:37 AM
Kylian Kylian is offline
Registered User
 
Join Date: Jan 2020
Posts: 4
POST ID # = 1030933
Kylian Reputation: 10
Default

Thank you very much for your response, after trying about ten times, I managed to remove the air bubbles, I hardly hear them at all anymore.
Reply With Quote
Reply

Tags
h100, rgb platinium

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:55 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.