thelor Posted May 31, 2019 Share Posted May 31, 2019 Hi Guys, So i've recently injured myself quite badly and wont be moving around for a while decided to buy myself a gaming system (been about 4 years since the last one I had) the specs are as follows: Phanteks Enthoo Evolv (galaxy silver) Intel i7 8700k EVGA 1080ti FTW3 11gb Corsair Dominator Platinum 16GB 3200Mhz (2 x 8gb) ASUS STRIX z370-e Motherboard EVGA 280mm CLC Seasonic focus plus platinum 850w Samsung 970 evo 250gb Crucial MX500 Western Digital Baracuda 2tb HDD 4 x Corsair ML140 Pro (rgb) Fans 2 x Corsair ML140 Fans Clean install with all the latest drivers, I've installed the EVGA software for the clc and the GPU So onto my question, on my old build I used to be able to go into the BIOS and enabled XMP and continue with no issues. I've tried enabling XMP on this machine and I noticed after I had left my system on overnight the mouse was freezing every 30 seconds or so and the whole machine felt unstable, If i use the default settings in the bios everything runs fine (im no expert but i think this means im not getting the full speeds from my system) I've ran prime using large tests on default settings and everything seems fine, once I enable XMP then start gaming / benchmarking my temps rise considerably and i've also noticed my vcore voltage reaching 1.4+ I'm just abit unsure on what to do, i'd like to get the most out of the system i've got and would appreciate any help or advice <3 (sorry for the bad english) I've included screengrabs but can include anything else CheersxHWMonitor.txt Link to comment Share on other sites More sharing options...
thelor Posted June 1, 2019 Author Share Posted June 1, 2019 Could anyone point me in the way of any decent guides on getting my ram / cpu to run at the correct speeds i've had a good google just wondering if there was any you recommend Link to comment Share on other sites More sharing options...
thelor Posted June 6, 2019 Author Share Posted June 6, 2019 no one ? :| Tried setting the ram and voltages myself but system becomes even more unstable Link to comment Share on other sites More sharing options...
Gronar Posted June 6, 2019 Share Posted June 6, 2019 Don't enable XMP, leave it on auto and try manually setting speed to 3200. Worked on my Asus board. Link to comment Share on other sites More sharing options...
c-attack Posted June 6, 2019 Share Posted June 6, 2019 (edited) Enabling XMP on a Asus Z370/390 board does a lot more than just set the RAM frequency and voltage. You'll notice enabling XMP is right on top of the Adv BIOS AI Tuner/Tweaker column along with manual and auto clocking. If you switch to XMP, you must redo all your settings. Short term solution -- as above. Manually set the DRAM frequency to 3200, enter the timings menu right below and input the primary timings from the RAM kit. Leave Asus tweak, Command Rate, and all the sub-timings on auto. The board will assign values as it runs tests on cold boot. Long term, you will want to read up on any overclock guides for the Asus Z370 (or the Z270 systems). There are a lot of Asus specific settings you want to lock down, even if you are not employing a strong overclock. The board in its default state is overclocked with a high dosage of voltage, so it tends to run warm straight out of the box. https://edgeup.asus.com/2017/kaby-lake-overclocking-guide/ Asus did not bother to make an official Z370 because more or less nothing changed from Z270. Here is the write up. A bit technical in places, but helpful in spots. There are also lots of user reviews out there. Edited June 10, 2019 by c-attack Hide n seek hyperlink Link to comment Share on other sites More sharing options...
thelor Posted June 9, 2019 Author Share Posted June 9, 2019 Really appreciate the response will test when I'm back Monday thank you had a nightmare getting it stable at all but sounds like I need to do more research Link to comment Share on other sites More sharing options...
thelor Posted June 10, 2019 Author Share Posted June 10, 2019 Do you have a link to the write up ? I noticed you said . Here is the write up. A bit technical in places, but helpful in spots. There are also lots of user reviews out there. couldn't find any hyperlink tho Link to comment Share on other sites More sharing options...
c-attack Posted June 10, 2019 Share Posted June 10, 2019 You definitely want to get off auto voltage, even if you want to run the default single core turbo speed. The board automatically defaults to a all core overclocking through a setting near the top of the AI Tweaker column called Multi-Core Enhancement (MCE). Turn this off. You can do the same thing yourself with one setting below while maintaining control (set all cores same frequency, you pick the multiplier). You can pick from manual/fixed or approve voltage. Fixed is usually better to start when finding your voltage. You’ll never be at 1.4. I use 1.30v for 5.0 which is slight better than average, but a reasonable place to start if that is your target frequency. Link to comment Share on other sites More sharing options...
thelor Posted June 13, 2019 Author Share Posted June 13, 2019 Hi Mate, So I managed to get it running using your suggestions changed the voltage from auto to 1.3 and put the clock at 48 (i'll provide pictures in a bit just at work) Everything seemed fine for a day then I noticed the computer freeze again, I've also noticed and this could be completely separate if I bring the PC out of sleep the freezing starts happening quite alot. not sure if the computer is downclocking then speeding back up Link to comment Share on other sites More sharing options...
Pocah Posted June 19, 2019 Share Posted June 19, 2019 Well if it doesn't work on XMP then it is most likely the motherboard and not the RAM. Fiddling settings may well help but may not. I would be more inclined to just step down the frequency. You honestly are not talking any performance difference with that CPU if you drop it down to 3000. Try using the XMP settings but with the frequency at 3000 instead of 3200. Link to comment Share on other sites More sharing options...
Recommended Posts