c0rs4ir Posted August 24, 2019 Share Posted August 24, 2019 I'm using M2A_SOCKET. BitLocker disabled. Okay good to know, btw I would very much appreciate if you could post a reply in this thread since you have the x570 AORUS XTREME board. Would be great to hear your opinion. Thanks Link to comment Share on other sites More sharing options...
Rimc_LT Posted September 4, 2019 Share Posted September 4, 2019 Try fill drive to 60 and more % and see if speed drops. On 1TB we have problem whit speeds then drive is filled. Link to comment Share on other sites More sharing options...
ahmed307731 Posted September 10, 2019 Share Posted September 10, 2019 Asus Crosshair Hero x570 (Latest Bios as of September 2019) AMD 3900x RTX 2080ti 64GB DDr4 Crucial ram 3600 Cl19 ( 1:1 in ryzen master) Crosair MP600 x 2 - 2tb (4tb total populating both slots) Same issue as OP - Read and write at max 2.7gbps , Tried fidgetuing with bios , setting PCIE1 + 2 to Gen 4 instead of aauto , tried decoupling . Havent tested corsair Secure wipe utility but will be filing for RMA if not resolved , Im goping to follow this thread and open a support ticket shortly after doing some more benchamrking and accumultaing bios screenshots etc . Ive been a logn term Corsair enthusiast and willing to work on this issue till its resolved , Im sure its just a bit of fidgeting thats required . If anyone has come up with anything please advise Link to comment Share on other sites More sharing options...
Corsair Employee Corsair Kevin Posted September 10, 2019 Corsair Employee Share Posted September 10, 2019 I'm still working with the firmware and SSD teams to see what's going on. I'll keep this thread updated as information comes in. Can everyone please try to update the firmware through SSD toolbox? 11.2 should be available. If it's not, please share screenshots of your drive information. Thank you! Link to comment Share on other sites More sharing options...
randall_785 Posted September 19, 2019 Share Posted September 19, 2019 I'm still working with the firmware and SSD teams to see what's going on. I'll keep this thread updated as information comes in. Can everyone please try to update the firmware through SSD toolbox? 11.2 should be available. If it's not, please share screenshots of your drive information. Thank you! MP600 1TB Latest firmware (11.2) Please advise. Link to comment Share on other sites More sharing options...
Corsair Employee Corsair Kevin Posted September 19, 2019 Corsair Employee Share Posted September 19, 2019 MP600 1TB Latest firmware (11.2) Please advise. What version of the BIOS are you on? Link to comment Share on other sites More sharing options...
randall_785 Posted September 20, 2019 Share Posted September 20, 2019 What version of the BIOS are you on? ABBA released 9/17 Link to comment Share on other sites More sharing options...
Corsair Employee Corsair Kevin Posted September 20, 2019 Corsair Employee Share Posted September 20, 2019 ABBA released 9/17 Thank you. I'm collecting data to see if we can pinpoint the cause. So far, it seems a bit random. Link to comment Share on other sites More sharing options...
Corsair Employee Corsair Kevin Posted September 20, 2019 Corsair Employee Share Posted September 20, 2019 To everyone who is encountering these issues with reduced performance, please provide the following via PM: Motherboard: CPU: Memory brand: Memory model: Memory capacity: Memory speed: BIOS Version: Windows Build and Version: MP600 capacity: MP600 serial number (a photo of the sticker would be great): MP600 Firmware Version: Using drive as OS or storage? Which M.2 slot? Stock heatsink on MP600? If no, what are you using for a heatsink? Link to comment Share on other sites More sharing options...
c0rs4ir Posted September 21, 2019 Share Posted September 21, 2019 (edited) Here are my CrystalDiskMark results for the Corsair MP600 2TB. Note: - BitLocker is ENABLED using the new AES-XTS encryption method - Testing right after a clean Windows 10 Pro installation (and installing latest chip-set drivers etc.) - The drive has 1,17 TB free of 1,81 TB Now to answer your questions: Motherboard: Gigabyte x570 Aorus Xtreme BIOS Version: F5a CPU: AMD Ryzen 3900x Memory brand: Corsair Memory model: CMW32GX4M2Z3200C16 Memory capacity: 32 GB Memory speed: XMP profile 1, 3200 MHz, 16-18-18-36-54 Windows Build and Version: Windows 10 Pro 10.0.18362 Build 18362 MP600 capacity: 2 TB MP600 serial number (a photo of the sticker would be great): I attached a photo of the sticker to this post MP600 Firmware Version: EGFM11.2 Using drive as OS or storage? OS Which M.2 slot? M2A_SOCKET Stock heatsink on MP600? MP600's pre-mounted heatsink Edited September 21, 2019 by c0rs4ir Link to comment Share on other sites More sharing options...
randall_785 Posted September 21, 2019 Share Posted September 21, 2019 Thank you. I'm collecting data to see if we can pinpoint the cause. So far, it seems a bit random. Kevin, I am probably not speaking for everyone, but I have just confirmed that the drive performs as expected when formatted. Only after I install windows do I see the drop in performance. What am I missing here? Any ideas? Please let me know. Thanks! Link to comment Share on other sites More sharing options...
johnmarc1337 Posted September 23, 2019 Share Posted September 23, 2019 Hi @all! Motherboard: Gigabyte X570 Aorus Ultra CPU: AMD Ryzen 7 3700X 8-Core Processor Memory brand: Corsair Memory model: Corsair CMT16GX4M2C3600C18 Memory capacity: 2x 8GB Memory speed: DDR4-3600 (1800 MHz) BIOS Version: F6a Windows Build and Version: Windows 10 Enterprise 64 Bit 1903, 18362.356 MP600 capacity: 1TB MP600 serial number (a photo of the sticker would be great): 192482290001285514B8 MP600 Firmware Version: EGFM11.0 Using drive as OS or storage? Both, Partition C:\ OS (250 GB), Partition D:\ Games and data (750GB) Which M.2 slot? M2A_SOCKET Stock heatsink on MP600? yes CrystalDiskMark, see attachments Greetings John Marc Link to comment Share on other sites More sharing options...
Seegee911 Posted September 24, 2019 Share Posted September 24, 2019 (edited) Has anyone tried running Atto Disk Benchmark? I'm getting some really wierd results on write speeds which may shed some light on things... The speeds seem to be oscillating... Goes proper speed for a bit, then drops, and repeats... I'll post a screenshot of this when I get home. Atto gives several measurements at various block sizes, which provides more granularity than the basic "one number" output CDM gives... I ran the test several times in sequence with hwinfo updates @ 500ms intervals and temps never went above 52C, averaging 47C. Note that Run #1 and #4 are the exact same settings, but there is crazy variance in performance from one test to the next. If you can run atto, please post your results here Edited September 25, 2019 by Seegee911 Link to comment Share on other sites More sharing options...
johnmarc1337 Posted September 25, 2019 Share Posted September 25, 2019 I tried same tests like Seegee911 and an addional test with big filesize, 16GB. Results are attached. Link to comment Share on other sites More sharing options...
Seegee911 Posted September 25, 2019 Share Posted September 25, 2019 (edited) Yeah, that's pretty much what I am experiencing as well. Interesting results from the 16Gb test. There was speculation earlier that CDM read test was causing the drive to heat up, and thus a possible throttle situation during the write portion of CDM. However with Atto, it performs the write test before the read test, but the speed variance only shows on write performance. Read speeds remain unaffected... I will run the 16gig test myself later, and I will be monitoring the temps while I do it. EDIT: I added my 16G test, temps were still fine. 50C or less Edited September 26, 2019 by Seegee911 Link to comment Share on other sites More sharing options...
johnmarc1337 Posted September 25, 2019 Share Posted September 25, 2019 My Temps are under 55°C during the tests. I'm very interested in what happened on your 16GB test. Link to comment Share on other sites More sharing options...
Seegee911 Posted September 26, 2019 Share Posted September 26, 2019 Tweak Town just released a new review of the 2tb MP600 here which they ran several different benchmarks including atto, which gave them perfect results. They claim that the benchmarks were done with the drive at 50% capacity, and according to their ssd toolbox screenshots they are also using fw 11.2. I'm going to be reaching out to them to see if they can replicate these issues. Link to comment Share on other sites More sharing options...
Corsair Employee Corsair Kevin Posted October 2, 2019 Corsair Employee Share Posted October 2, 2019 For everyone experiencing performance issues with the MP600, at this point, I would highly suggest RMA'ing your units. Visit http://www.corsair.com/support and start a ticket. Please title your ticker "MP600 FORUM RMA" and also include this in the ticket notes as well. I personally want to see the issue resolved, and this is the fastest way to do so. This will allow us to receive the units, test them firsthand, and hopefully determine what the issue is. Link to comment Share on other sites More sharing options...
johnmarc1337 Posted October 3, 2019 Share Posted October 3, 2019 Hi Kevin! Sorry, but this is not an option for me. I unterstand that you want to test the units, but the SSD is in use and i need my PC for work. If you send me another SSD before, i could send my SSD to you? Link to comment Share on other sites More sharing options...
Corsair Employee Corsair Kevin Posted October 3, 2019 Corsair Employee Share Posted October 3, 2019 Hi Kevin! Sorry, but this is not an option for me. I unterstand that you want to test the units, but the SSD is in use and i need my PC for work. If you send me another SSD before, i could send my SSD to you? Hi John, when you start the ticket, in the notes just mention this and the support staff can help you set up what's called an Advanced RMA. They will require a credit card number just to put a hold for the amount of a new SSD on it and we'll send a unit to you before you send yours in. You'll have some time to clone your current drive to the new one (or do a fresh install, which is what I'd recommend), and then send the other unit in for failure analysis. The hold will be released on your card, and all will be good in the world (I hope. :)) Link to comment Share on other sites More sharing options...
racdavies Posted January 5, 2020 Share Posted January 5, 2020 While i dont have performance issues with my MP600 2tb i find it very hit n miss under pci-e 3.0, im currently running an i7 7700k on an Asus z270a, my primary drive is a Samsung 970pro 1tb and my mp600 is in my second nvme slot, in addition to these drives i also run a Samsung 850 evo 2tb and a Sandisk ultra II 960gig dds. Ive been running dual nvme drives for over a year and the mp600 is the 3rd drive in the second slot that ive tried but ive never had the issues i haver atm, issues range from drive dissapearing from my desktop to corrupt files and inaccessible folders, usually the issues disapear after a reboot but soon return after accessing the drive for a few minutes, as i said this is the 3rd drive ive used with this setup so i know this is an issue with the drive.....maybe its just not stable under pci-e gen 3, also Icue shows the mp600 idling at 33c....pretty much the same as my Samsung 970pro. My mp600 is only used for games. Link to comment Share on other sites More sharing options...
hbh Posted January 9, 2020 Share Posted January 9, 2020 Is it possible to replace the original M.2 SSD with a MP600 2tb in a Corsair One i182? Link to comment Share on other sites More sharing options...
hbh Posted January 24, 2020 Share Posted January 24, 2020 Can someone answer this question please? Link to comment Share on other sites More sharing options...
Adas Posted May 25, 2020 Share Posted May 25, 2020 Hi - BitLocker is ENABLED using the new AES-XTS encryption method What does "using the new AES-XTS encryption method" mean? It means: BitLocker with enabled hardware encryption built in MP600 drive? Link to comment Share on other sites More sharing options...
naujoks Posted June 15, 2020 Share Posted June 15, 2020 My 4K read speeds are not good either. Z390 board, new Win 10 Pro install, all recent drivers and BIOS. Any idea what might be the problem? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now