arg-ist Posted September 25, 2015 Share Posted September 25, 2015 G5 BENCH As ı said before there are 2 new MAC G5 mods on the table.My first worklog MAC G5 ATX (passive watercooled) is finished. I take final photos.I t is time to begin with a new worklog. 1-My first worklog was MAC ATX (passive watercooled) http://imagizer.imageshack.us/v2/1280x1024q90/913/35DzGf.jpg http://imagizer.imageshack.us/v2/1280x1024q90/673/IsBN0e.jpg http://imagizer.imageshack.us/v2/1280x1024q90/537/GNkEZq.jpg Link MAC G5 ATX Passive watercooled. http://forum.corsair.com/forums/showthread.php?t=135867 2. This time again a MAC G5 , but as a BENCH CASE. 3-And my next worklog again a MAC G5 … But this time as a JUMBO MAC G5 = MAC G5 STACKER MAC G5 STACKER http://imagizer.imageshack.us/v2/1280x1024q90/673/IwtfpS.jpg I want to make a TRILOGY with MAC G5 cases. This time ı want to make a different BENCH CASE from this case. A combination of aluminum and acrylic. I will use this case R1 http://imagizer.imageshack.us/v2/1280x1024q90/537/C18Nmn.jpg But ı wll use only back side panel and the four handles of the case R 2 http://imagizer.imageshack.us/v2/1280x1024q90/661/W6tgzw.jpg Case tilted R 3 http://imagizer.imageshack.us/v2/1280x1024q90/537/9ZFmhI.jpg As a bench case there are two ways that we can use. 1-Handles at front and back panels R4 http://imagizer.imageshack.us/v2/1280x1024q90/901/MNI8Zb.jpg 2-Handles at sides I shall use it , this way. R 5 http://imagizer.imageshack.us/v2/1280x1024q90/540/HHdzqe.jpg I want to install 2x360 rads in to the bulge of handles. And PSU ,POMP ,HDD etc . in this case R 6 http://imagizer.imageshack.us/v2/1280x1024q90/540/fHClPB.jpg As usally, MB on the top, on a thick plexi, as MB TRAY .that can be opened to back. As ı used it at my first BENCH Worklog http://imagizer.imageshack.us/v2/800x600q90/842/spuc.jpg And ı wannt to mount the video card with a 16X riser card extender flex. To prevent the height of the case ,becouse ı wannt to make a flap cover from plexi.(If ı can do it…) R6a http://imagizer.imageshack.us/v2/1280x1024q90/661/TQdxZo.jpg Link to comment Share on other sites More sharing options...
arg-ist Posted October 2, 2015 Author Share Posted October 2, 2015 First a recess for rads and rad grils in to the handles , from acrylic. Drawn at corel R 7 http://imagizer.imageshack.us/v2/1024x768q90/911/iwE71Q.jpg And laser cut from 5 mm acrylic R 8 http://imagizer.imageshack.us/v2/1280x1024q90/540/Iqlotg.jpg To bend the acrylics, ı made a mold from MDF. R 9 http://imagizer.imageshack.us/v2/1280x1024q90/661/FiS2BQ.jpg I can bend acrylic using this mold R10 http://imagizer.imageshack.us/v2/1280x1024q90/905/afP90A.jpg Acrylic plate on the mold R 11 http://imagizer.imageshack.us/v2/1280x1024q90/538/l1WfZo.jpg Acrylic plate fixed to the mold Resim12 http://imagizer.imageshack.us/v2/1280x1024q90/537/TUvIab.jpg Heating of acrylic with heat gun. R 13 http://imagizer.imageshack.us/v2/1280x1024q90/673/3XeZI2.jpg And bending of softened acrylic R 14 http://imagizer.imageshack.us/v2/1280x1024q90/538/OCtiAA.jpg Bended acrylics R 15- 16 http://imagizer.imageshack.us/v2/1280x1024q90/661/J0BPPH.jpg http://imagizer.imageshack.us/v2/1280x1024q90/673/ylu2Fw.jpg Bended acrylic mounted to the case for trial purposes. R 17-18-19 http://imagizer.imageshack.us/v2/1280x1024q90/911/o9NyVh.jpg http://imagizer.imageshack.us/v2/1280x1024q90/537/x00I3r.jpg http://imagizer.imageshack.us/v2/1280x1024q90/661/F1MInW.jpg And second side panel bended likewise. R 20 http://imagizer.imageshack.us/v2/1280x1024q90/909/9LbE01.jpg Two side panels are ready R 21 http://imagizer.imageshack.us/v2/1280x1024q90/910/ZoaxOg.jpg Second side panel mounted too… for trial purposes R 22-23 http://imagizer.imageshack.us/v2/1280x1024q90/661/YMWwb9.jpg http://imagizer.imageshack.us/v2/1280x1024q90/540/LbMmHO.jpg Link to comment Share on other sites More sharing options...
arg-ist Posted October 9, 2015 Author Share Posted October 9, 2015 Four Silverstone case feets mounted to the bottom of the case R25 http://imagizer.imageshack.us/v2/1280x1024q90/537/ichDfH.jpg Next stage is front and back panel Made from 3mm thick acrylic a pattern for front and back panel. And mounted to control. Resim24 http://imagizer.imageshack.us/v2/1280x1024q90/538/nxv2us.jpg At front panel ı don t wannt to use a lott of displays. I want to use 2x lcd temp. displays for radiator entries and 2x lcd temp. Display for rad outputs.total 4 LCD displays for temp. And a fan controllerfor fans. And some researches for their placement R26-27-28-29 http://imagizer.imageshack.us/v2/1280x1024q90/912/04xV8t.jpg http://imagizer.imageshack.us/v2/1280x1024q90/673/8W3xGF.jpg http://imagizer.imageshack.us/v2/1280x1024q90/903/zurJcP.jpg http://imagizer.imageshack.us/v2/1280x1024q90/912/a3Mmjr.jpg I have tried with different reservoirs EK X3, Bitspower. With 60 mm Radius. but I do not like any the most appropriate was EK Tube res X3 60 mm R38 http://imagizer.imageshack.us/v2/1280x1024q90/905/ReiEZF.jpg but want to keep the cables of PSU. Masking could be a solution to it.. R 39 40 41 http://imagizer.imageshack.us/v2/1280x1024q90/911/Cz39rT.jpg http://imagizer.imageshack.us/v2/1280x1024q90/901/YVpSE7.jpg http://imagizer.imageshack.us/v2/1280x1024q90/903/Gzpu2C.jpg I wanted a different solution At last ı decided to use a wider resorvoir 150mm Radius , to make reservoir as essential element. I must make a Jumbo reservoir from acrylic tube like this R30 http://imagizer.imageshack.us/v2/1280x1024q90/911/8CuwvE.jpg And use reservoir as essential element. of the buttom case like this R 31 32 33 Reservoir with extrem 150mm Radius. Was to big for this case. http://imagizer.imageshack.us/v2/1280x1024q90/913/p5YtIz.jpg http://imagizer.imageshack.us/v2/1280x1024q90/912/JsyQpn.jpg http://imagizer.imageshack.us/v2/1280x1024q90/911/mu3NlF.jpg Therefore ı decided to make it with 120 mm Radius R 34 35 36 37 http://imagizer.imageshack.us/v2/1280x1024q90/631/4lsVo7.jpg http://imagizer.imageshack.us/v2/1280x1024q90/631/VzQa0A.jpg http://imagizer.imageshack.us/v2/1280x1024q90/910/rMZMav.jpg http://imagizer.imageshack.us/v2/1280x1024q90/911/eZtz5Y.jpg It is time to make a custom Tube reservoir with 120 mm Radius. Link to comment Share on other sites More sharing options...
Trophy Posted October 16, 2015 Share Posted October 16, 2015 Not that I like Macs that much but this looks sick! And that case overall is quite clean :) Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.