vvcepheus7 Posted April 15, 2012 Share Posted April 15, 2012 Hi, For my new SSD force 3 in Tech Specs say: 550 MB/s sequential read But when I run a test I get 250MB/s read. What reason? I need config any parameter of windows? I use SATA3 of 6gbps. I've two tests: http://imageshack.us/photo/my-images/51/capturatuq.jpg/ http://imageshack.us/f/844/captura2iz.jpg/ any solution? Link to comment Share on other sites More sharing options...
Turbonerfs101e Posted April 15, 2012 Share Posted April 15, 2012 hi you ave to test SSD with ATTO benchmarck to get accurat speed Link to comment Share on other sites More sharing options...
vvcepheus7 Posted April 15, 2012 Author Share Posted April 15, 2012 I test it another time with 3 software and in nothing case work at 550mb/s. read 420MB/s max write 170MB/s max this is normal? or the ssd is bad? I woult must change? I do anithing wrong? anyone can get more than 500MB/s (write/read) ???? in there say that my results is not corrects: http://guru3d.com/article/corsair-force-3-120gb-ssd-review/10 thanks! Link to comment Share on other sites More sharing options...
vvcepheus7 Posted April 15, 2012 Author Share Posted April 15, 2012 another test here: 400/170 MB/s Link to comment Share on other sites More sharing options...
wlw_wl Posted April 15, 2012 Share Posted April 15, 2012 What motherboard, what SATA 3 controller? I had it running faster than specs on Intel controller on Z68 board. Link to comment Share on other sites More sharing options...
vvcepheus7 Posted April 15, 2012 Author Share Posted April 15, 2012 Asus p9x79 pro Chipset x79 Sata 3 marvell 9128 Driver 1.2.0.1014 It is normal??! Ssd is broken? Link to comment Share on other sites More sharing options...
Turbonerfs101e Posted April 15, 2012 Share Posted April 15, 2012 Marvell 9128 chip is no good as it us a pcie 1x interface Mutch to slow for sata3 SSD Got the same problem on my DX58SO2 using marvell 9128, got to buy a pcie 8x controller Only Z68 and x79 motherboard is able to run ssd at full speed If u or using marvell controller Go in bios and desable marvell controller and plug your SSD on Intel® X79 controller. you will see if you desable marvell controller windows sould start in lest then 8sec.(you probely need to reinstall windows if you do be sure to save all your save game and important folder on usb key or other hard drive and do a secure erease before formating ur ssd) In fact, in bios desable all material that you ar not ussing It will speed up your system Hope this help Sincerly yours Link to comment Share on other sites More sharing options...
vvcepheus7 Posted April 15, 2012 Author Share Posted April 15, 2012 thank you very much! you were right! actually the problem was the controller marvell 9128. When I connected the sata ssd connector x79 chipset performance has been correct. I attach a screen capture. It really is amazing that asus say marvell controler it is 6Gbps when lie. 6 hours of my time lost by this nonsense! :P One more thing, what parameters configuration ssd windows 7 x64 you recommend me ? I have seen many guides for configuring Windows. you could clarify me in each case whether to increase system performance or if it is only to increase the life of the ssd? Thank you again! Link to comment Share on other sites More sharing options...
Turbonerfs101e Posted April 15, 2012 Share Posted April 15, 2012 Did you try desable the marvell controller in bios As it slow down windows startup Windows sould start in lest then 8sec. To optimise ssd performance you sould set Intel® X79 controller in ACHI mode Link to comment Share on other sites More sharing options...
vvcepheus7 Posted April 18, 2012 Author Share Posted April 18, 2012 Thank you! I do it all this and the result is espectacular! kind regards Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.