Search the Community
Showing results for tags 'water cooler'.
-
Hello there, After installing my new ICUE H100i Elite Capellix I noticed only the LED on the pump was lighting up. I thought that it was weird that the fans didn't light up but I went to the ICUE application hoping it was a setting I needed to adjust. After learning how to use the ICUE application, I did the "Lighting Wizard 4-Pin Setup" and to my surprise no fans were detected. Luckily I had another fan handy and tried to use it through the controller that came in the box with the H100i, and it worked! The fan was detected and I was able to use all the controls including the LED controls. So that leads me to believe that something is wrong with the LED's on the fan it came with. So to recap here is everything I tried: 1) Using a different fan 2) Uninstalling IQUE and reinstalling 3) Using an older version of ICUE 4) Plugging only one fan in at a time 5) Using a previous version of windows 6) Disabling ANYTHING that could be effecting/monitoring the fans 7) Switching around the order of which the fans are plugged into the controller To my knowledge I installed everything correctly considering the fact that I used the video on how to install it from Corsair's website. It's super frustrating and sad that I've had nothing but problems when it comes to Corsair's LEDs. I had a three pack of Corsair fans a few years ago and it was the worst thing ever. My PC is almost ready for a full rebuild and I was going to go full Corsair but if I can't get these LED lights to work I might as well but from elsewhere. There are a ton of good products out that the LED's actually work on them. The worst part about the whole thing is that I've been trying to fix it for hours now and I feel as if I've done everything humanly possible and it still fails to work properly. If anyone has a solution to this or has a faced a similar problem please help me! Also, something I forgot to mention... When in BIOS no fans that are plugged into the controller are detected. Just the pump shows up under BIOS but in the ICUE software I can see all fans that are plugged in. Could it be a problem with USB that's plugged into the motherboard from the controller itself? So confused and lost here, Ill add some pictures if that helps, thanks for reading if you made it this far!
-
Hi! I updated the firmware of my water cooler to the latest version (1.01.32). Now i'm having some issues when i power my pc up. Before the update, the rgb lights of the pump appeared after 1 second, now it tooks 5 to 10 seconds to light up. Also, i'm having some kinda flushing noise that i didn't have before. I'm sure is related to this firmware. The thing is i need an older one or the one that came with the H100i. Does anyone has it? Thanks in advance!!!
- 8 replies
-
- firmware bug
- h100i rgb pro xt
-
(and 1 more)
Tagged with:
-
Pessoal, bom dia/tarde/noite. Estou com um problema com water cooler Corsair H100I, comprei de segunda mão, ele está funcionado tudo certinho, porem não consigo mexer nas FANS e nem no RGB da bomba, já tentei de varias maneiras resolver esse problema (troquei cabo USB, coloquei nas portas USB do computador, baixei outras versões do corsair link, instalar drive manual), porem sem sucesso. Alguém sabe se pode ser problema na bomba ou se tem mais alguma maneira que eu não tentei ? OBS: No Windows o drive do water cooler aparece como dispositivo USB desconhecido, já tentei em outros computadores mas aparece a mesma coisa. Poderiam me ajudar ? Obrigado!
- 1 reply
-
- corsair 100i
- fix or clean
-
(and 1 more)
Tagged with:
-
Hey guys, hope you're good. So I built my system 5 years ago for music production. The last couple of weeks it has pretty much ground to a halt. I get an error on startup saying CPU fan error and now the CPU is running at 100C*. Also Corsair link isn't displaying any information about the system when it worked before. The fans on the back that the pipes connect to still spin. Am I right in thinking this could be as simple as needing to re-apply thermal paste or could the pump be gone? Really need to get back making music! Thanks a lot. :biggrin:
-
I have a Commander Pro and a Lighting Node Pro. The Commander Pro is connected to the motherboard via usb header, and the lighting node pro is connected to the Commander Pro via usb header passthrough. I'm using the 4 LED strips included with the lighting node pro, and two of the strips are connected to the Commander Pro, and the other two are connected to the Lighting Node Pro. All 4 LED strips are lit up, but my iCUE only detects my Commander Pro, and thus I'm allowed to change two of the LED strips, but not all four. Can someone please help me figure out why iCUE is not detecting my Lighting Node? P.S. I have a H150i water cooler, is this also supposed to be detected by iCUE?