Jump to content
Corsair Community

Newbie overclock GA-P35-DS4


V8 Animal

Recommended Posts

Hi,

I have recently overclocked my pc and would like someone to take a look at my settings and point out if there is a problem or not please.

I have tested it with prime.occt,and memtest+ all without errors.

Only snag i have hit is memtest v3.5 won't run.

Current Bios Settings:

Robust Graphics Booster______________ [Fast]

CPU Clock Ratio ____________________ [9]

CPU Host Clock Control______________ [100]

CPU Host Frequency (MHz)___________ [333]

PCI Express Frequency (Mhz)__________ [Enabled]

C.I.A. 2____________________________ [Disabled]

System Memory Multiplier (SPD)_______ [3.2]

Memory Frequency __________________ 800 1066

DRAM Timing Selectable_______ SPD __ [Manual]

Performance Enhance = [standard]

 

CAS Latency Time___________________ 5 [5]

Dram RAS# to CAS# Delay____________ 5 [5]

Dram RAS# Precharge Delay___________ 5 [5]

Precharge Delay (tRAS)_______________ 18 [15]

ACT to ACT Delay (tRRD)_____________ 3 [5]

Rank Write to READ Delay____________ 3 [8]

Write to Precharge Delay______________ 6 [8]

Refresh to ACT Delay_________________ 52 [56]

Read to Precharge Delay_______________ 3 [6]

Static tRead Value____________________ 6 [7]

Static tRead Phase Adjust______________ 0 [Auto]

 

System Voltage Control________________ [Manual]

DDR2 OverVoltage Control____________ [+.30v]

PCI-E OverVoltage Control____________ [+.10v]

FSB OverVoltage Control______________ [+.10v]

(G)MCH OverVoltage Control__________ [+.10v]

CPU Voltage Control_________________ [1.29375v]

 

Current Advanced Bios Settings:

CPU Hyperthreading _________________ Not Available

Limit CPUID Max to 3 _______________ Disabled

No Execute mem. Protect _____________ Enabled

CPU enhanced Halt (CIE) _____________ Disabled

CPU EIST Function __________________ Disabled

Virtualization Tech. __________________ Enabled

Thanks;):

Link to comment
Share on other sites

Could i be cheeky and ask for settings for 3.2 or 3.4 won't go above that or should i stick with what ive got?

Ive had a go myself but it fails to boot so i assume i need to alter a few more settings than the ones i have already done.

Thanks for any help.

Btw i have altered static tread value to 8 i have also read somewhere that the refresh to ACT delay should be 70 for 2x2GB is that right?

Cheers

Link to comment
Share on other sites

I usually just set it to Auto and leave it up to the enumeration of the BIOS to implement. You seem to know enough to test the machine and get an overclock out of it. You've got the machine, not me so I advise you to play with it. I help those who don't know what they are doing to find baseline overclocks, show them how to set values, but in the final analysis, it's up to them then and I can see by your settings that you know enough to test on your own.

 

As long as you don't overvolt the DRAM you will not hurt it so play with the settings if you want minimal (if any) increases. I use the main settings and performance settings. The rest of the settings I set to Auto.

 

You have a very low Vcore, so you certainly need to look at Vcore when increasing the FSB past 333Mhz. ~1.3v is certainly not going to easily make 3.4Ghz. I use a top down philosophy. I do not set low, I set high, find stability and then begin to lower voltages and fully test the machine.

 

Could i be cheeky and ask for settings for 3.2 or 3.4 won't go above that or should i stick with what ive got?

Ive had a go myself but it fails to boot so i assume i need to alter a few more settings than the ones i have already done.

Thanks for any help.

Btw i have altered static tread value to 8 i have also read somewhere that the refresh to ACT delay should be 70 for 2x2GB is that right?

Cheers

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...