The Corsair User Forums  

Go Back   The Corsair User Forums > Corsair Product Discussion > Corsair Link

Closed Thread
 
Thread Tools Search this Thread Rate Thread Display Modes
  #31  
Old 08-19-2014, 07:05 AM
no1yak no1yak is offline
Registered User
no1yak's PC Specs
 
Join Date: Jan 2012
Posts: 68
POST ID # = 723535
no1yak Reputation: 26
Default

Just installed this version of CL and one of my 240 ssd's is showing 1.0 degrees c. All other drives show correct temp. Previous versions of CL showed all drives at correct temp.
In this version my ssd's are shown as Corsair ssd Assembly except the one which says "Drive Temp"- that the drive which is at 1.0 degrees.


  #32  
Old 08-19-2014, 07:47 AM
hotroderinn hotroderinn is offline
Registered User
hotroderinn's PC Specs
 
Join Date: Aug 2014
Posts: 6
POST ID # = 723542
hotroderinn Reputation: 10
Default

H80i (bomb, rpm, temp) doesn't appear. Legacy usb disable.
Fans conected to bomb doesn't appear either.

Is it so difficult release a software that works?

And second H80i replacing for defective issues.


  #33  
Old 08-19-2014, 08:21 AM
MojoVersion8 MojoVersion8 is offline
Enthusiast
MojoVersion8's PC Specs
 
Join Date: Jan 2011
Location: Sydney, Australia
Posts: 183
POST ID # = 723544
MojoVersion8 Reputation: 12
Default

1. v2.7.5339
2. motherboard fans not always read
3. only one of my case fans are read (rest just say 0 rpm), this might be due to the fans not having been started until after boot up which is weird thing my motherboard does when the fans aren't set to run at full speed

Will probably be getting a Commander Mini eventually anyway which should do a much better job than my motherboard


  #34  
Old 08-19-2014, 10:40 AM
hpvoltage hpvoltage is offline
Registered User
 
Join Date: Dec 2012
Posts: 16
POST ID # = 723549
hpvoltage Reputation: 12
Default

Windows 8.1 x64
Asus Z87-Deluxe
Corsair h100i
Corsair 1200w AXI

Coolers H100i not detected ( Legacy USB Support Disabled in BIOS )


  #35  
Old 08-19-2014, 10:45 AM
Fauxbeard's Avatar
Fauxbeard Fauxbeard is offline
Corsair Employee
Fauxbeard's PC Specs
 
Join Date: Jan 2014
Location: Fremont, CA
Posts: 339
POST ID # = 723551
Fauxbeard Reputation: 19
Default

Quote:
Originally Posted by MojoVersion8 View Post
1. v2.7.5339
2. motherboard fans not always read
3. only one of my case fans are read (rest just say 0 rpm), this might be due to the fans not having been started until after boot up which is weird thing my motherboard does when the fans aren't set to run at full speed

Will probably be getting a Commander Mini eventually anyway which should do a much better job than my motherboard
Link will only read sensors made available by the motherboard. The Commander Mini will fill this gap if you want to control your case fans.
__________________


  #36  
Old 08-19-2014, 10:50 AM
Fauxbeard's Avatar
Fauxbeard Fauxbeard is offline
Corsair Employee
Fauxbeard's PC Specs
 
Join Date: Jan 2014
Location: Fremont, CA
Posts: 339
POST ID # = 723552
Fauxbeard Reputation: 19
Default

Quote:
Originally Posted by N9887L View Post
1. v2.7.5339
2. Detects everything except H100i
3. See #2. Activity LED on back of Commander unit flashes green through system startup, then green with intermittent red post-OS load.
What does "everything" comprise of? Is the H100i connected to the Commander?
__________________


  #37  
Old 08-19-2014, 12:05 PM
Alek123 Alek123 is offline
Registered User
Alek123's PC Specs
 
Join Date: Aug 2014
Posts: 1
POST ID # = 723587
Alek123 Reputation: 10
Default

1. Latest v2.7.5339
2. Windows 8.1 Pro x64
3. H100i not detected. USB Legacy Support Disabled. Motherboard/CPU/GPU/HDD is detected, while H100i is not.
4. Corsair Link detects pretty much every sensor but doesn't detect H100i or its' fans. Also grammar error on Devices/Options "Check for Updates". It returns "did not detect anay devices" instead of "any".

Any tips to make it detect my H100i?


  #38  
Old 08-19-2014, 12:59 PM
MojoVersion8 MojoVersion8 is offline
Enthusiast
MojoVersion8's PC Specs
 
Join Date: Jan 2011
Location: Sydney, Australia
Posts: 183
POST ID # = 723594
MojoVersion8 Reputation: 12
Default

Quote:
Originally Posted by Alek123 View Post
1. Latest v2.7.5339
2. Windows 8.1 Pro x64
3. H100i not detected. USB Legacy Support Disabled. Motherboard/CPU/GPU/HDD is detected, while H100i is not.
4. Corsair Link detects pretty much every sensor but doesn't detect H100i or its' fans. Also grammar error on Devices/Options "Check for Updates". It returns "did not detect anay devices" instead of "any".

Any tips to make it detect my H100i?
might be consided risky but you could try deleting the device store in the registry (HKEY_CURRENT_USER > Software > Corsair > CorsairLINK > Devices) when you uninstall the software (so it's completely cleaned out) then resinstall it
this worked for me when that happened

Quote:
Originally Posted by Corsair Bunny Foo Foo #5 View Post
Link will only read sensors made available by the motherboard. The Commander Mini will fill this gap if you want to control your case fans.
they are made available but not right away, like when I start up HWMonitor after my PC boots up it sees only one fan then after a few seconds the rest show up
almost as though the motherboard wont do anything with them until the software tries to see if they are there
just seems that the software doesn't pick up on them dynamically

I'll I really want to do is set these fans to run at a set speed rather than maxed out so the Commander Mini will do me fine

Last edited by MojoVersion8; 08-19-2014 at 01:13 PM.


  #39  
Old 08-19-2014, 02:20 PM
Doridian Doridian is offline
Registered User
Doridian's PC Specs
 
Join Date: Aug 2014
Posts: 49
POST ID # = 723610
Doridian Reputation: 10
Default

1. v2.7.5339
2. Windows 8.1 Pro 64-bit
3. Corsair Link started using 10% CPU (i7-4790k, so essentially one full core). After a restart of Corsair Link (right click -> exit on the icon, then starting it again), all H100i sensors were zero and the LED was blank. Reboot did not fix. Had to delete the profile and reboot to fix. The AX1200i sensors were fine even tho the AX1200i is attached to the H100i.


  #40  
Old 08-19-2014, 02:47 PM
bommie bommie is offline
Registered User
 
Join Date: Feb 2013
Posts: 34
POST ID # = 723617
bommie Reputation: 10
Default

1. v2.7.5339
2. Windows 8.1 Pro 64-bit

fans speed works for a day ,then impossible to switch between profile ans speed stuck at the same ....
back to old version , at least that one was working ....


  #41  
Old 08-19-2014, 03:18 PM
shine6 shine6 is offline
Registered User
shine6's PC Specs
 
Join Date: Aug 2011
Posts: 45
POST ID # = 723626
shine6 Reputation: 10
Default

Hello,

Installed this version with Widows 7 64bits and H100i (No Link comander).

Works fine so far.

My H100 still have 1.0.5 firmware. I didn't try the upgrade into 1.0.7 (yet).

Should I? Did someone tried already?

Thanks!

Shine


  #42  
Old 08-19-2014, 03:51 PM
Protocol48's Avatar
Protocol48 Protocol48 is offline
Registered User
Protocol48's PC Specs
 
Join Date: Apr 2014
Location: Pomona, NY
Posts: 148
POST ID # = 723631
Protocol48 Reputation: 14
Default

1. Version: 2.7.5339
2. Windows 8.1 Pro-64 bit
3. Issues using Corsair Commander, Cooling, GPU & Lighting Nodes : Missing Memory Temp from AirFlow Pro to Commander; SSD okay, but have 2 Identical WD HD's & 1 Seagate. "Devices" state 1 WD w/ 1 sensor, and 1 Seagate with 2 sensors,
4. Picture Attached to save web page space.
1. Version: 2.7.5339
2. Windows 8.1 Pro-64 bit
3. Issues using Corsair Commander MINI, GPU & Lighting Nodes: Missing Memory Temp from AirFlow Pro, Reporting one of the two identical (not RAID) WD Drives. No Power Tab, No AX860i Data at all.
4 Picture Attached to save web page space.

Last edited by Protocol48; 08-27-2014 at 04:04 PM. Reason: Added Commander Mini to data


  #43  
Old 08-19-2014, 04:06 PM
Tech_Greek Tech_Greek is offline
Registered User
Tech_Greek's PC Specs
 
Join Date: Jul 2014
Posts: 26
POST ID # = 723635
Tech_Greek Reputation: 5
Default

Version of your Link software. NOTE: If you're not using v2.7.5339, please install it and see if the bug has been fixed.
What version of Windows you're using.
Summary - One line / sentence explaining the issue
Detailed description of the issue - This part can be as long as you want. It should be detailed enough so that we can clearly identify the issue and attempt to replicate it.
Attach photos of the issue to the post that help #4.
  1. v2.7.5339
  2. Windows 8.1 (U1) Enterprise
  3. Re-size Issues
  4. I am unable to re-size the UI when having icons placed on top of the picture. If I do, they automatically move. The program also has a tendency to restore in restored state even if I force it to start with a maximized window. This is all on a 1080p resolution.

    If I restore I also have to use Windows Key + M to Maximize the Window fully. I believe this is just a resolution based issue. I'm glad to see DPI Scaling is back and working fully as well as the run minimized upon startup fixed (but can we get rid of the message that link is still running? We know this after the first time).

Before & After:





  #44  
Old 08-19-2014, 04:24 PM
antonyfrn antonyfrn is offline
Registered User
antonyfrn's PC Specs
 
Join Date: Aug 2009
Location: London & spain
Posts: 225
POST ID # = 723636
antonyfrn Reputation: 20
Default

1. Version: 2.7.5339
2. Windows 8.1 Pro-64 bit
3. H100i shows zero for all values fan temps and pump
4. Installed the new version made sure old profiles where removed everything looked ok till the right click menu seemed to lock up killed CorsarLink.exe now H100i and 4 stock fans no longer show any readings.


  #45  
Old 08-19-2014, 08:57 PM
Hamdawg Hamdawg is offline
Hamdawg
Hamdawg's PC Specs
 
Join Date: Sep 2013
Location: Canada
Posts: 1
POST ID # = 723667
Hamdawg Reputation: 10
Default

1. v2.7.5339
2. Win 7 64bi
3. Does not detect my second video card at all


Closed Thread

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:47 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.