The Corsair User Forums  

Go Back   The Corsair User Forums > Corsair Enthusiasts Section > System Builds, Modding, Custom Components, and Picture Gallery

Reply
 
Thread Tools Search this Thread Display Modes
  #361  
Old 10-16-2019, 06:28 AM
Zotty's Avatar
Zotty Zotty is online now
CORSAIR Beta Team
Zotty's PC Specs
 
Join Date: Apr 2017
Location: South Staffordshire, England, UK
Posts: 3,183
POST ID # = 1021421
Zotty Reputation: 52
Default

wait....

so...

plugged into your PSU you would have a cable with 4 Sata Power Connectors.. each Sata Power connector is 4.5A max...... and I don't recommend using Sata Power 'y' splitters...
Reply With Quote


  #362  
Old 10-17-2019, 02:50 AM
Fwashy Fwashy is offline
Registered User
Fwashy's PC Specs
 
Join Date: Dec 2018
Posts: 18
POST ID # = 1021531
Fwashy Reputation: 10
Default

Quote:
Originally Posted by Zotty View Post
wait....

so...

plugged into your PSU you would have a cable with 4 Sata Power Connectors.. each Sata Power connector is 4.5A max...... and I don't recommend using Sata Power 'y' splitters...
Wow, I was being reeaaallly stupid haha.
I thought you meant the plug that goes into the PSU at the end of the sata cable, not each individual sata connector haha .
My bad!
I definitely don't use y splitters on the sata lines, that would be far too scary for my system
Well that still leaves me with a problem, why did 5 LEDs in 5 of my fans go faulty around the same time

Thanks for helping ease my mind about the sata lines, I have no worries now other than, will more of my fans keep dying on me

Enjoy your day off with the build bud!

Last edited by Fwashy; 10-17-2019 at 02:52 AM.
Reply With Quote


  #363  
Old 10-17-2019, 05:22 AM
Zotty's Avatar
Zotty Zotty is online now
CORSAIR Beta Team
Zotty's PC Specs
 
Join Date: Apr 2017
Location: South Staffordshire, England, UK
Posts: 3,183
POST ID # = 1021541
Zotty Reputation: 52
Default

i have no answer as to why you have had 5 go bad at same time buddy.. its a very unusual situation.. i can only go off of my own experience which is, i have had 6 LL fans in my 570x build since the LL fans day of release (2 years or so?) not a single issue.. to add to that.. 30 of them in my 1000d and again.. no issues.. although that is a relatively new situation so time will tell.. wish i could help further dude
Reply With Quote


  #364  
Old 10-17-2019, 11:26 AM
DevBiker's Avatar
DevBiker DevBiker is offline
CORSAIR Beta Team
DevBiker's PC Specs
 
Join Date: Feb 2017
Location: Republic of Texas
Posts: 7,689
POST ID # = 1021572
DevBiker Reputation: 88
Default

The limit is 4.5A for each SATA connector, not for each cable from the PSU.
__________________
Please click "Edit System Specs" and fill out your system info.

This comment is provided "as-is", without warranty of any kind, express or implied, including, but not limited to, the sanity or mental fitness of the author. The author is not a Corsair employee, does not represent Corsair, and no comment should be construed as an official statement from Corsair.

Reply With Quote


  #365  
Old 10-17-2019, 11:31 AM
Zotty's Avatar
Zotty Zotty is online now
CORSAIR Beta Team
Zotty's PC Specs
 
Join Date: Apr 2017
Location: South Staffordshire, England, UK
Posts: 3,183
POST ID # = 1021574
Zotty Reputation: 52
Default

Quote:
Originally Posted by Zotty View Post
wait....

so...

plugged into your PSU you would have a cable with 4 Sata Power Connectors.. each Sata Power connector is 4.5A max...... and I don't recommend using Sata Power 'y' splitters...
yep.. already told him lol
Reply With Quote


  #366  
Old 10-18-2019, 09:17 AM
Fwashy Fwashy is offline
Registered User
Fwashy's PC Specs
 
Join Date: Dec 2018
Posts: 18
POST ID # = 1021653
Fwashy Reputation: 10
Default

Yup I got told haha.
Thanks though... I hope I can find a reason why the LEDs went bust in the first place.
I'm just glad it's not because of incompatibility :)
Reply With Quote


  #367  
Old 10-24-2019, 11:04 AM
Str7 Str7 is offline
Registered User
 
Join Date: Oct 2019
Posts: 1
POST ID # = 1022232
Str7 Reputation: 10
Default

Thanks for the great explanation on all of the details. This post was extremely helpful for me and my friend. We also, was able to create a great website that would be helpful for lots of man - https://getfree.bet/en/tips
Reply With Quote


  #368  
Old 10-24-2019, 03:21 PM
Zotty's Avatar
Zotty Zotty is online now
CORSAIR Beta Team
Zotty's PC Specs
 
Join Date: Apr 2017
Location: South Staffordshire, England, UK
Posts: 3,183
POST ID # = 1022243
Zotty Reputation: 52
Default

Update..

Rads/Fans/Pump/Drains (front and back)/GPU Block/flow-temp sensor/filter all fitted

this was my final RGB/Fan Control setup





Excuse the AOI and its cable mess. so far i have managed to keep it as a running system while adding bits here and there.




I decided to try the GPU in the ITX mounts to give a bit more room (lol) running tubing behind the GPU as well as give me room to add a small wifi/BT card. Should be noted the the cover/plate for the itx rear IO and its PSU has to be 'modded' so you can use the case itx pci slots without said itx being fitted (hope that made sense lol..




Not so sure i will stick with the fittings that run from GPUU to upper Rad in the below image.. i feel it suddenly looks 'industrial' so may do a ben or 2 there

http://i.imgur.com/HWpuVHEl.jpg[/img]

Last edited by Zotty; 10-24-2019 at 03:40 PM.
Reply With Quote


  #369  
Old 10-28-2019, 02:06 PM
dk7988 dk7988 is offline
Registered User
dk7988's PC Specs
 
Join Date: Oct 2019
Posts: 2
POST ID # = 1022565
dk7988 Reputation: 10
Default

Hey guys, newbie to this forum here, I was wondering if it would be possible for someone to post pictures of the D1000 with a tape measure thrown across it in the mobo bay. I'm trying to figure out how the 14"x14" ASUS ROG Dominus Extreme mobo and cooling res. would bolt up and fit in it. Thanks for any and all help
Reply With Quote


  #370  
Old 10-29-2019, 02:27 AM
Zotty's Avatar
Zotty Zotty is online now
CORSAIR Beta Team
Zotty's PC Specs
 
Join Date: Apr 2017
Location: South Staffordshire, England, UK
Posts: 3,183
POST ID # = 1022601
Zotty Reputation: 52
Default

i will be able to when i get home from work later today buddy
Reply With Quote


  #371  
Old 10-30-2019, 11:19 AM
dk7988 dk7988 is offline
Registered User
dk7988's PC Specs
 
Join Date: Oct 2019
Posts: 2
POST ID # = 1022707
dk7988 Reputation: 10
Default

much appreciated, Thanks!
Reply With Quote


  #372  
Old 11-01-2019, 07:10 PM
Zotty's Avatar
Zotty Zotty is online now
CORSAIR Beta Team
Zotty's PC Specs
 
Join Date: Apr 2017
Location: South Staffordshire, England, UK
Posts: 3,183
POST ID # = 1022858
Zotty Reputation: 52
Default

Update.

2nd Hydro X XdD5 Pump/Res Combo added and the loop split into 2. (CPU/GPU)







Reply With Quote


  #373  
Old 11-02-2019, 06:06 AM
frig frig is offline
Registered User
 
Join Date: Nov 2019
Posts: 4
POST ID # = 1022875
frig Reputation: 10
Default

hi Zotty,

i am bulding a similar rig but i do have one question about hydro X how did you set Hydro X Series XF Ball Valve?
i mean i am lost what did you used to set it up with any other part?

Quote:
Originally Posted by Zotty View Post
Update.

2nd Hydro X XdD5 Pump/Res Combo added and the loop split into 2. (CPU/GPU)







Reply With Quote


  #374  
Old 11-02-2019, 06:18 AM
Zotty's Avatar
Zotty Zotty is online now
CORSAIR Beta Team
Zotty's PC Specs
 
Join Date: Apr 2017
Location: South Staffordshire, England, UK
Posts: 3,183
POST ID # = 1022876
Zotty Reputation: 52
Default

hey buddy..


here is how i did mine




out of rad to T piece.. 90 degree rotary on bottom of T piece and tap screwed on the the 90 degree rotary
Reply With Quote


  #375  
Old 11-02-2019, 06:24 AM
frig frig is offline
Registered User
 
Join Date: Nov 2019
Posts: 4
POST ID # = 1022877
frig Reputation: 10
Default

thx mate for the zoom pic but i still dont get what piece you are using to fit two pieces of metal together
maybe with Hydro X Series XF Rotary Y-Splitter by just taking the bottom part?

Quote:
Originally Posted by Zotty View Post
hey buddy..


here is how i did mine




out of rad to T piece.. 90 degree rotary on bottom of T piece and tap screwed on the the 90 degree rotary

Last edited by frig; 11-02-2019 at 06:26 AM.
Reply With Quote


Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.