kingofgames Posted November 5, 2011 Share Posted November 5, 2011 1/Here is my SSD Corsair Force Series GT 120 GB SATA 2.5-Inch SATA III Solid State Drive (CSSD-F120GBGT-BK) Sometimes, I dont know what reason it appear a Blue Screen. I tried to update a new firmwave for that drive. But I press (Corsair_FieldUpdater_v1.1) the rescan many time, but it didn't see any SSD I have. http://img831.imageshack.us/img831/3628/115201172526pm.png Uploaded with ImageShack.us 2/how can I clearing of the BIOS? 3/I have a MArvell 91xx drive in my PC. Do I have to uninstall it? 4/what is Secure Erase ? how can I Secure Erase ? 5/ In Technical Details: It said Sequential read speeds of up to 555 MB/s Sequential write speeds of up to 515 MB/s but when I use AS SSD Benchmark check or CrystalDiskMark, it show read : 378Mb/s, and Write is so little : 89mb/s only..can you tell me why? is that SSD defective? Here is ATTO Disk Benchmark http://img406.imageshack.us/img406/5963/1152011110513pm.png Uploaded with ImageShack.us and here is AS SSD Benchmark http://img408.imageshack.us/img408/3326/1152011110759pm.png Uploaded with ImageShack.us Link to comment Share on other sites More sharing options...
Toasted Posted November 6, 2011 Share Posted November 6, 2011 2. Short the pins or remove the CMOS battery (refer to motherboard user manual) 3. Plug the SSD in an Intel SATA port (refer to motherboard user manual) Once you plugged it in the Intel port is it detected in the updater? Link to comment Share on other sites More sharing options...
kingofgames Posted November 6, 2011 Author Share Posted November 6, 2011 1/3. Plug the SSD in an Intel SATA port (refer to motherboard user manual) Once you plugged it in the Intel port is it detected in the updater? I just did..it worked..thanks...I installed windows 7 on Marvell Sata 6.0..(if I changed to intel Sata 6.0, Do I need to install windows 7 again? (does it work fine?) 2/2. Short the pins or remove the CMOS battery (refer to motherboard user manual) I don't know what section in my manual about CMOS battery..can you tell me what is page in my manual? 3/ I have a MArvell 91xx drive in my PC. Do I have to uninstall it? Link to comment Share on other sites More sharing options...
Toasted Posted November 6, 2011 Share Posted November 6, 2011 1. No, you don't need to 2. 2-31 and 2-34 3. You can't uninstall it as it is soldered on to the motherboard. All you can do is avoid it but if you don't have stability issues or freezes then you can plug the SSD in to the Marvell Ports. Link to comment Share on other sites More sharing options...
kingofgames Posted November 7, 2011 Author Share Posted November 7, 2011 3. You can't uninstall it as it is soldered on to the motherboard. All you can do is avoid it but if you don't have stability issues or freezes then you can plug the SSD in to the Marvell Ports. Reply With Quote Before when my SSD was still in the Marvell Ports, it had 2-3 times appeared Blue Screen. Do you think if I switch SSD from the Marvell Ports to Intel SATA port, it won't appear the blue screen again? or I have to upgrade the Firmware 1.3.3 for my SDD? Link to comment Share on other sites More sharing options...
Toasted Posted November 7, 2011 Share Posted November 7, 2011 It may have been the Marvell Controller causing it. But if you are still gettting BSODs on the Intel SATA port update the firmware. Link to comment Share on other sites More sharing options...
kingofgames Posted November 7, 2011 Author Share Posted November 7, 2011 2. 2-31 and 2-34 Can you check that again? those pages are about 6GB and 3GB for intel SATA..not about "Short the pins or remove the CMOS battery" . Everytime if I do that, do I need to install new windows 7 64bit again? Link to comment Share on other sites More sharing options...
Toasted Posted November 8, 2011 Share Posted November 8, 2011 Sorry, Downloaded the wrong manual 2-29 Link to comment Share on other sites More sharing options...
kingofgames Posted November 8, 2011 Author Share Posted November 8, 2011 that is about clear RTC Ram (real Time Clock).. I didnt see about clearing of the BIOS? can you point out? sorry..Im not smart... ?_? Link to comment Share on other sites More sharing options...
Toasted Posted November 8, 2011 Share Posted November 8, 2011 RTC is the BIOS. But was reading the manual and there is a clear CMOS switch. just press that page 2-52. Probably a more easier way. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.