finalware Posted November 11, 2008 Share Posted November 11, 2008 I want to know EXACTLY what I need to change in Rampage Extreme BIOS to suite my specs Link to comment Share on other sites More sharing options...
DerekT Posted November 11, 2008 Share Posted November 11, 2008 Download CoreTemp Here Please post a screenshot of CoreTemp. I need to know the revision of that CPU. Link to comment Share on other sites More sharing options...
finalware Posted November 11, 2008 Author Share Posted November 11, 2008 Here it's !CoreTemp-Scr.bmp Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted November 11, 2008 Corsair Employee Share Posted November 11, 2008 Derek I am sure will help in more detail with the settings but the tested settings of the modules can be found from the link in my signature and that is where I would start. Link to comment Share on other sites More sharing options...
finalware Posted November 11, 2008 Author Share Posted November 11, 2008 http://www.houseofhelp.com/forums/showthread.php?t=54052 Testing parameters for TWIN3X/XMS3-1800C8D: will this settings workk with me ? the settings here was in p5k3 and p5e3 i'm runing on a stable system now but on the minimum settings i run the memory on 1333 and the cpu 333*8.5 Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted November 11, 2008 Corsair Employee Share Posted November 11, 2008 Yes and the settings ti try are in that link but the MB you have may not be able to reach these settings depending on the CPU you have. Testing parameters for TWIN3X/XMS3-1800C8D: TW3X4G1800C8DF Data Sheet Motherboard make and model: ASUS P5K3, P5E3 Premium/Deluxe ! Each pair is tested and packaged together using the following settings: Advanced Jumper Free AI Overclock: Manual CPU Control: Manual FSB Frequency: 450 MHz PCIE Frequency: AUTO DRAM Frequency: DDR3-1800 MHz DRAM Command Rate: 2T/2N DRAM Timings Control: Manual CAS# Latency:___________8 RAS# to CAS# Delay:______8 RAS# Precharge:__________8 RAS# Activate to Precharge:24 DRAM Static Read Control: Disabled DRAM Dynamic Write Control: Disabled CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled CPU Voltage:__________Auto CPU PLL Voltage:_______Auto DRAM Voltage:_________1.76V FSB Termination Voltage:_Auto North Bridge Voltage:____1.71V All settings not listed should be left at AUTO or BIOS Default Maximum DDR3 recommended VDIMM: 2.00 Volts Link to comment Share on other sites More sharing options...
finalware Posted November 16, 2008 Author Share Posted November 16, 2008 Look guys it's still stable only on 1333 settings and i've tried alot of settings but no use , plz i need a full recipe :s Link to comment Share on other sites More sharing options...
finalware Posted November 16, 2008 Author Share Posted November 16, 2008 Does any one know a good settings for oc the cpu and make it works higher than 2.83 ! Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted November 18, 2008 Corsair Employee Share Posted November 18, 2008 I doubt a 9550 will reach that speed they usually top out at about 400 MHz, but you will have to lower the multiplier and go from there. Link to comment Share on other sites More sharing options...
DerekT Posted November 18, 2008 Share Posted November 18, 2008 You have the E(0) revision of that CPU and should be able to make a 450Mhz FSB. But you need to have a good CPU cooler and NOT the stock Intel one. Download Memtest86+ V2.01 from--->Hereand extract the ISO image. Burn the ISO image to an CD-ROM disk. Download CPU-z from Here .Extreme Tweaker Ai Overclock Tuner: Manual OC From Memory Level Up: Auto FSB Frequency: 450 CPU Ratio Setting: 8.5 CPU Configuration CPU Ratio Setting: 8.5 C1E Support: Disabled CPU TM Function: Enabled Max CPUID Value Limit: Disabled Vanderpool Technology: Enabled Execute Disable Bit: Enabled Core Multi-Processing: Enabled CPU Clock Skew: Auto NB Clock Skew: Auto FSB Strap to North Bridge: 400 PCIE Frequency: 101 DRAM Frequency: 1800 DRAM Command Rate: 2N DRAM Timing Control: Manual CAS# Latency: 8 RAS# to CAS# Delay: 8 RAS# Pre Time: 8 RAS# ACT Time: 24 RAS# To RAS# Delay: Auto REF Cycle Time: Auto WRITE Recovery Time: Auto READ to Pre Time: Auto READ to WRITE Delay (S/D): Auto WRITE to READ Delay (S): Auto WRITE to READ Delay (D): Auto READ to READ (S): Auto READ to READ (D): Auto WRITE to WRITE (S): Auto WRITE to WRITE (D): Auto WRITE to PRE Delay: Auto READ to PRE Delay: Auto PRE to PRE Delay: Auto ALL PRE to ACT Delay: Auto ALL PRE to REF Delay: Auto DRAM Static Read Control: Disabled DRAM Dynamic Write Control: Disabled DRAM Skew Control DRAM CMD Skew on Channel A: Auto DRAM CLK Skew on DIMM A1: Auto DRAM CLK Skew on DIMM A2: Auto DRAM CTL Skew on DIMM A1: Auto DRAM CTL Skew on DIMM A2: Auto DRAM CMD Skew on Channel B: Auto DRAM CLK Skew on DIMM B1: Auto DRAM CLK Skew on DIMM B2: Auto DRAM CTL Skew on DIMM B1: Auto DRAM CTL Skew on DIMM B2: Auto Ai Clock Twister: Auto Ai Transaction Booster: Auto Common Performance Level: Auto EPU II Phase Control: On CPU Voltage: Auto Load-Line Calibration: Disabled CPU PLL Voltage: Auto FSB Termination Voltage: Auto CPU GTLVerf (0): Extreme Tweaker Ai Overclock Tuner: Manual OC From Memory Level Up: Auto FSB Frequency: 450 CPU Ratio Setting: 8.5 CPU Configuration CPU Ratio Setting: 09.0 C1E Support: Disabled CPU TM Function: Enabled Max CPUID Value Limit: Disabled Vanderpool Technology: Enabled Execute Disable Bit: Enabled Core Multi-Processing: Enabled CPU Clock Skew: Delay 300ps NB Clock Skew: Delay 200ps FSB Strap to North Bridge: 400 PCIE Frequency: 101 DRAM Frequency: 1880 DRAM Command Rate: 1N DRAM Timing Control: Manual CAS# Latency: 8 RAS# to CAS# Delay: 8 RAS# Pre Time: 8 RAS# ACT Time: 24 RAS# To RAS# Delay: Auto REF Cycle Time: Auto WRITE Recovery Time: Auto READ to Pre Time: Auto READ to WRITE Delay (S/D): Auto WRITE to READ Delay (S): Auto WRITE to READ Delay (D): Auto READ to READ (S): Auto READ to READ (D): Auto WRITE to WRITE (S): Auto WRITE to WRITE (D): Auto WRITE to PRE Delay: Auto READ to PRE Delay: Auto PRE to PRE Delay: Auto ALL PRE to ACT Delay: Auto ALL PRE to REF Delay: Auto DRAM Static Read Control: Disabled DRAM Dynamic Write Control: Disabled DRAM Skew Control DRAM CMD Skew on Channel A: Auto DRAM CLK Skew on DIMM A1: Auto DRAM CLK Skew on DIMM A2: Auto DRAM CTL Skew on DIMM A1: Auto DRAM CTL Skew on DIMM A2: Auto DRAM CMD Skew on Channel B: Auto DRAM CLK Skew on DIMM B1: Auto DRAM CLK Skew on DIMM B2: Auto DRAM CTL Skew on DIMM B1: Auto DRAM CTL Skew on DIMM B2: Auto Ai Clock Twister: Auto Ai Transaction Booster: Auto Common Performance Level: Auto EPU II Phase Control: Auto CPU Voltage: Auto Load-Line Calibration: Disabled CPU PLL Voltage: Auto FSB Termination Voltage: Auto CPU GTLVerf (0): Extreme Tweaker Ai Overclock Tuner: Manual OC From Memory Level Up: Auto FSB Frequency: 450 CPU Ratio Setting: 8.5 CPU Configuration CPU Ratio Setting: 09.0 C1E Support: Disabled CPU TM Function: Enabled Max CPUID Value Limit: Disabled Vanderpool Technology: Enabled Execute Disable Bit: Enabled Core Multi-Processing: Enabled CPU Clock Skew: Delay 300ps NB Clock Skew: Delay 200ps FSB Strap to North Bridge: 400 PCIE Frequency: 101 DRAM Frequency: 1880 DRAM Command Rate: 1N DRAM Timing Control: Manual CAS# Latency: 8 RAS# to CAS# Delay: 8 RAS# Pre Time: 8 RAS# ACT Time: 24 RAS# To RAS# Delay: Auto REF Cycle Time: Auto WRITE Recovery Time: Auto READ to Pre Time: Auto READ to WRITE Delay (S/D): Auto WRITE to READ Delay (S): Auto WRITE to READ Delay (D): Auto READ to READ (S): Auto READ to READ (D): Auto WRITE to WRITE (S): Auto WRITE to WRITE (D): Auto WRITE to PRE Delay: Auto READ to PRE Delay: Auto PRE to PRE Delay: Auto ALL PRE to ACT Delay: Auto ALL PRE to REF Delay: Auto DRAM Static Read Control: Disabled DRAM Dynamic Write Control: Disabled DRAM Skew Control DRAM CMD Skew on Channel A: Auto DRAM CLK Skew on DIMM A1: Auto DRAM CLK Skew on DIMM A2: Auto DRAM CTL Skew on DIMM A1: Auto DRAM CTL Skew on DIMM A2: Auto DRAM CMD Skew on Channel B: Auto DRAM CLK Skew on DIMM B1: Auto DRAM CLK Skew on DIMM B2: Auto DRAM CTL Skew on DIMM B1: Auto DRAM CTL Skew on DIMM B2: Auto Ai Clock Twister: Auto Ai Transaction Booster: Auto Common Performance Level: Auto EPU II Phase Control: Auto CPU Voltage: Auto Load-Line Calibration: Disabled CPU PLL Voltage: Auto FSB Termination Voltage: Auto CPU GTLVerf (0): Auto CPU GTLVerf (1): Auto CPU GTLVerf (2): Auto CPU GTLVerf (3): Auto NB GTLVerf: Auto North Bridge Voltage: Auto DRAM Voltage: 1.80v NB DDRVref: Auto DDR3 ChannelA Vref: Auto DDR3 ChannelB Vref: Auto South Bridge 1.5 Voltage: Auto South Bridge 1.05 Voltage: Auto CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled CPU GTLVerf (1): +50mv CPU GTLVerf (2): +50mv CPU GTLVerf (3): +50mv NB GTLVerf: +60mV North Bridge Voltage: Auto DRAM Voltage: 1.80 NB DDRVref: Auto DDR3 ChannelA Vref: Auto DDR3 ChannelB Vref: Auto South Bridge 1.5 Voltage: Auto South Bridge 1.05 Voltage: Auto CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled CPU GTLVerf (1): +50mv CPU GTLVerf (2): +50mv CPU GTLVerf (3): +50mv NB GTLVerf: +60mV North Bridge Voltage: Auto DRAM Voltage: 1.80 NB DDRVref: Auto DDR3 ChannelA Vref: Auto DDR3 ChannelB Vref: Auto South Bridge 1.5 Voltage: Auto South Bridge 1.05 Voltage: Auto CPU Spread Spectrum: Disabled PCIE Spread Spectrum: DisabledRun Memtest for two full passes. When assured of stable DRAM, then enter Windows and Run CPU-z and post screenshots of CPU-z's CPU, Memory and SPD tabs. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.