Jump to content
Corsair Community

CMX4GX3M2A1600C9 on GA-EP45T UD3LR


h4mz

Recommended Posts

okay, its hear stupid, but i buy RAM that is maybe not listed by corsair on here..

everybody can help me with my details specs how to configuring and tuning this RAM on my Mobo please..

when i use 2 RAM on slot 0 and 2 its no problem

when i use 4 RAM on slot 0-1-2-3 my installed operating system go die (7 ultimate get BSOD), my ubuntu goes freeze

i don't know howto and about setting RAM in bios so i need help on this forum

BTW my MoBo is not listed on here why ? this MoBo is using DDR3 too

Link to comment
Share on other sites

I'll try howto set the bios

i will show the result and i will show to u the result too..

but if there any wrong settings please help to suggest me the right settings

sorry for my really bad english

Link to comment
Share on other sites

With 4 modules I would suggest you set the memory frequency at DDR1066 or DDr1333 and set the memory Voltage to 1.7 Volts and see if it will pass http://www.memtest.org.

this is my setting, i search on google and find this

but this is not work on my board system got freeze and memtest result error

MB Intelligent Tweaker(M.I.T.)

Robust Graphics Booster ...............: Auto

CPU Clock Ratio ..........................: 7X

Fine CPU Clock Ratio.....................:.+0.5

CPU Frequency ...........................: 2.5GHz (333x7.5)

 

 

Clock Chip Control

Standard Clock Control

CPU Host Clock Control..................: [Enabled]

CPU Host Frequency (Mhz) ............: 333Mhz

PCI Express Frequency (Mhz) .........: 100

C.I.A.2 .................................:[Disabled]

 

 

Advanced Clock Control [Press Enter]

CPU Clock Drive...........................: 800mV

PCI Express Clock Drive.................: 800mV

CPU Clock Skew (ps)....................: 0ps

MCH Clock Skew (ps)...................: 0ps

 

 

DRAM Performance Control

Performance Enhance...................: [standard]

(G)MCH Frequency Latch...............: [Auto]

System Memory Multiplier ..............: Auto

Memory Frequency (Mhz) ..............: 1066

DRAM Timing Selectable ................: [Manual]

 

Standard Timing Control

CAS Latency Time........................ 9

tRCD ................................... 9

tRP'.................................... 9

tRAS.................................... 24

 

Advanced Timing Control

tRRD.......................................... 4 Auto

tWTR.......................................... 4 Auto

tWR........................................... 8 Auto

tRFC.......................................... 60 Auto

tRTP.......................................... 4 Auto

Command Rate (CMD) ........................... 0 Auto

 

Driving Strength Profiles

Driving Strength ............................

 

Channel A

Static tRead Value.........................:8 Auto

tRD Phase0 Adjustment...................: 0 Auto

tRD Phase1 Adjustment...................:0 Auto

tRD Phase2 Adjustment .................:0 Auto

tRD Phase3 Adjustment..................:0 Auto

Trd2rd(Different Rank)....................:9 Auto

Twr2wr(Different Rank)...................:7 Auto

Twr2rd(Different Rank)...................:7 Auto

Trd2wr(Same/Diff Rank)..................:10 Auto

Dimm1 Clock Skew Control...............:Auto ps

Dimm2 Clock Skew Control...............:Auto ps

DDR Write Leveling.....................:Auto

DDR Write Training.....................:Auto

 

Channel B

Static tRead Value.........................:9 Auto

tRD Phase0 Adjustment...................:1 Auto

tRD Phase1 Adjustment...................:1 Auto

tRD Phase2 Adjustment .................:1 Auto

tRD Phase3 Adjustment..................:0 Auto

Trd2rd(Different Rank)....................:9 Auto

Twr2wr(Different Rank)...................:7 Auto

Twr2rd(Different Rank)...................:7 Auto

Trd2wr(Same/Diff Rank)..................:10 Auto

Dimm1 Clock Skew Control...............:Auto ps

Dimm2 Clock Skew Control...............:Auto ps

DDR Write Leveling.....................:Auto

DDR Write Training.....................:Auto

 

Motherboard Voltage Control

Voltage Type.………... Manual

CPU

CPU Vcore….……….........................:1.2V

CPU Termination….......................:1.2V

CPU PLL………………….........................:1.550V

CPU Reference.………….......................:0.805V

 

MCH/ICH

MCH Core……………........................: 1.2V

MCH Reference….…….0.760V...........; <<< Auto

ICH I/O……………….....1.550V............: <<< Auto

ICH Core…………...……1.100V............: <<< Auto

 

DRAM

DRAM Voltage ……......................: 1.7V

DRAM Termination .…0.750V............: <<< Auto

 

Advanced Settings

Limit CPUID Max. to 3.....................: [Disabled]

No-Execute Memory Protect............: [Enabled]

CPU Enhanced Halt (C1E)................: [Disabled]

CPU Thermal Monitor 2(TM2) ...........: [Enabled]

CPU EIST Function.........................: Disabled

Virtualization Technology................: Enabled

Link to comment
Share on other sites

  • Corsair Employee

t

Standard Timing Control

CAS Latency Time........................ 9

tRCD ................................... 9

tRP'.................................... 9

tRAS.................................... 24

 

Advanced Timing Control

tRRD.......................................... 4 Auto

tWTR.......................................... 4 Auto

tWR........................................... 8 Auto

tRFC.......................................... 60 Auto

tRTP.......................................... 4 Auto

Command Rate (CMD) .....................2T

MCH/ICH

MCH Core……………........................: 1.4V

Link to comment
Share on other sites

after i update the settings, my box just cannot boot, event in BIOS, so i unplugged 3 power cable 2 from HDD and 1 Optical drive and it is still cannot boot, so i reset the bios finally boot

the latest settings when im cannot boot my box is

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 7X
Fine CPU Clock Ratio.....................:.+0.5
CPU Frequency ...........................: 2.5GHz (333x7.5)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333Mhz
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mV
PCI Express Clock Drive.................: 800mV
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps


DRAM Performance Control
Performance Enhance...................: [standard]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: Auto
Memory Frequency (Mhz) ..............: 1333 ->changed
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................ 9
tRCD ................................... 9
tRP'.................................... 9
tRAS.................................... 24

Advanced Timing Control
tRRD.......................................... 4 Auto
tWTR.......................................... 4 Auto
tWR........................................... 8 Auto
tRFC.......................................... 60 Auto
tRTP.......................................... 4 Auto
Command Rate (CMD) ........................... 2 Auto ->changed

Driving Strength Profiles
Driving Strength ............................

Channel A
Static tRead Value.........................:8 Auto
tRD Phase0 Adjustment...................: 0 Auto
tRD Phase1 Adjustment...................:0 Auto
tRD Phase2 Adjustment .................:0 Auto
tRD Phase3 Adjustment..................:0 Auto
Trd2rd(Different Rank)....................:9 Auto
Twr2wr(Different Rank)...................:7 Auto
Twr2rd(Different Rank)...................:7 Auto
Trd2wr(Same/Diff Rank)..................:10 Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
DDR Write Leveling.....................:Auto
DDR Write Training.....................:Auto

Channel B
Static tRead Value.........................:9 Auto
tRD Phase0 Adjustment...................:1 Auto
tRD Phase1 Adjustment...................:1 Auto
tRD Phase2 Adjustment .................:1 Auto
tRD Phase3 Adjustment..................:0 Auto
Trd2rd(Different Rank)....................:9 Auto
Twr2wr(Different Rank)...................:7 Auto
Twr2rd(Different Rank)...................:7 Auto
Trd2wr(Same/Diff Rank)..................:10 Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
DDR Write Leveling.....................:Auto
DDR Write Training.....................:Auto

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:1.2V
CPU Termination….......................:1.2V
CPU PLL………………….........................:1.550V
CPU Reference.………….......................:0.805V

MCH/ICH
MCH Core……………........................: 1.4V -> changed
MCH Reference….…….0.760V...........; <<< Auto
ICH I/O……………….....1.550V............: <<< Auto
ICH Core…………...……1.100V............: <<< Auto

DRAM
DRAM Voltage ……......................: 1.7V
DRAM Termination .…0.750V............: <<< Auto

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: Disabled
Virtualization Technology................: Enabled 

now i think im going crazy.. overclocking is fun, but i absolutely have no basic and experience on overclocking the PC.

please suggest me the correct settings

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...