The Corsair User Forums  

Go Back   The Corsair User Forums > Corsair Product Discussion > Cooling

Reply
 
Thread Tools Search this Thread Rating: Thread Rating: 68 votes, 5.00 average. Display Modes
  #31  
Old 12-30-2013, 06:15 PM
peanutz94's Avatar
peanutz94 peanutz94 is offline
Support Assistant
peanutz94's PC Specs
 
Join Date: Feb 2011
Location: Akron,Ohio
Posts: 9,740
POST ID # = 690086
peanutz94 Reputation: 84
Default

I just used a drop of dish washing soap on the screw to give them a little lube . They go right in. A drop of silicone lubricant works just as well and will also let you remove them pretty easily. WD-40 makes one in a spray can . IJust spray a little on the cap and dip your screws in .

Just another suggestion guys.
__________________
NO, I do not work for Corsair! But I am an official forum helper.
Reply With Quote


  #32  
Old 01-03-2014, 05:28 PM
tpbarratt tpbarratt is offline
Registered User
 
Join Date: Dec 2013
Posts: 6
POST ID # = 690717
tpbarratt Reputation: 10
Default

Corsair need to address this issue asap. The product is clearly not fit for purpose.
Reply With Quote


  #33  
Old 08-02-2014, 05:01 PM
srome srome is offline
Registered User
srome's PC Specs
 
Join Date: Jul 2014
Posts: 24
POST ID # = 721515
srome Reputation: 10
Default

sAme issue with a Sp120 quiet edition screws not even half way in an the rubber mount was stopping me fully tightening the screws I'm sure they will fall apart if I fully tighten. the screws are way oversized, total joke for a £10 fan.

I see the work around, but there should be no need for a work around this is a fan not rocket science and looking at the dates on these posts corsair don't seem interested to fix this manufacturing defect.
Reply With Quote


  #34  
Old 08-03-2014, 03:40 PM
Tech_Greek Tech_Greek is offline
Registered User
Tech_Greek's PC Specs
 
Join Date: Jul 2014
Posts: 26
POST ID # = 721603
Tech_Greek Reputation: 5
Default

You don't have to tighten the fans down all the way, it defeats the purpose of the silicone bumpers. What I do is watch the fan bumpers and if they start to compressed I stop. They are held perfectly in place and can't wiggle. If the silicone is compressed, it'll be similar to having plastic vs metal vibrations.

I've had zero issues out any of the fans except for the first one in which I decided to drive it in without paying attention and that one vibrated. After I removed it and did as I described above, zero issues.

Also, if you hold the rubber mount with your hand and use the proper size Phillips bit you'll have no issues with stripping screws or anything of that nature (or not getting the screws in).
Reply With Quote


  #35  
Old 02-14-2015, 03:21 PM
GatlinGun GatlinGun is offline
GatlinGun
GatlinGun's PC Specs
 
Join Date: Feb 2015
Location: Texas
Posts: 3
POST ID # = 760286
GatlinGun Reputation: 10
Default

I too have had this same problem. While installing a set of SP120 (waiting for replacement from RMA) and now with an AF120. One installed just fine. The second one let me get three tight, but the fourth would not get close to the case before it spun.

While tightening the screws I am only turning about 1/8 of a turn, stop and let grommet return to rest, another 1/8th, stop, repeat until the screw becomes tight to the case.

I have seen the comments about dunking the screws in WD-40 or applying some silicon. Maybe when the new fan arrives I will try this.

Although I have also seen where some are using long screws that go through the full length of the fan and then placing a nut on the opposite end. This is a great idea and possibly what should be supplied with the fans as their mounting method. I am afraid to take the one that installed out to swap the provided screws with long ones.

It is sad that there are threads on this subject for many years. I am stuck on Corsair and really like their products. My Case, Memory, PSU and Cooler are all Corsair.

So frustrating though that something of this nature exists and isn't addressed.

A simple set of installation instructions with a tip on how to install these might reduce the RMAs. Not to mention a redesign of the hardware provided.
Reply With Quote


  #36  
Old 07-01-2015, 12:14 PM
JayStar JayStar is offline
Registered User
JayStar's PC Specs
 
Join Date: Jul 2015
Posts: 5
POST ID # = 787584
JayStar Reputation: 10
Default

Same issue - just got mine today and trying to fit them. Screw goes in a couple of turns then stops. It can be made to work by literally doing a quarter turn at a time back off , then doing another quarter turn etc.. I have one screw hole done outside the case - took 15 minutes - this really is laughable to be honest. I have a whole system to be built today and the fans will take approx. 7 hrs. at 1 hr per fan just because these things don't actually have any threads and you have to make them by screwing in to flimsy plastic - wow.
Reply With Quote


  #37  
Old 07-01-2015, 12:18 PM
JayStar JayStar is offline
Registered User
JayStar's PC Specs
 
Join Date: Jul 2015
Posts: 5
POST ID # = 787585
JayStar Reputation: 10
Default

second one done - it speeds up when you have the hang of it - make absolutely CERTAIN your screw driver really grabs the head of the screw. Absolutely no slipping or it will not work.
Reply With Quote


Reply

Tags
fan, problems, sp120

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:49 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.