The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Showing results 1 to 25 of 66
Search took 0.03 seconds.
Search: Posts Made By: L4d
Forum: Memory 12-11-2010, 08:25 AM
Replies: 2
Views: 2,611
Posted By L4d
RMA the bad module? Test each individually in one...

RMA the bad module? Test each individually in one slot to find which module is bad?
Forum: Memory 12-11-2010, 01:28 AM
Replies: 13
Views: 7,756
Posted By L4d
I now use +.075 voltage with my 720BE (C2...

I now use +.075 voltage with my 720BE (C2 revision) CPU's IMC @ 2.2ghz.
My motherboard is a GA-MA78LM-S2H, and it has but three phases and a four pin CPU power connection, so my .75 voltage might be...
Forum: Memory 10-10-2010, 03:48 PM
Replies: 2
Views: 4,254
Posted By L4d
2.1+ volts for any DDR2-1066?

2.1+ volts for any DDR2-1066?
Forum: Memory 09-27-2010, 06:42 PM
Replies: 17
Views: 7,883
Posted By L4d
Try DDR2-800D overclocked to 12x250 CPU...

Try DDR2-800D overclocked to 12x250 CPU tRAS:11-15 and tRC:13+ 2.1 volts? This is effective DDR2-1000.
Forum: Memory 09-27-2010, 06:40 PM
Replies: 1
Views: 2,622
Posted By L4d
Use default subtimings? Try DDR2-800C and tRAS:12...

Use default subtimings? Try DDR2-800C and tRAS:12 2.1 volts?
Forum: Memory 07-24-2010, 05:41 PM
Replies: 2
Views: 2,548
Posted By L4d
Try lowering all timings until it won't post or...

Try lowering all timings until it won't post or it fails Memtest.
Forum: Memory 07-24-2010, 05:35 PM
Replies: 13
Views: 7,756
Posted By L4d
Sorry for not adding a zero before; I meant...

Sorry for not adding a zero before; I meant .025-.05.
I feel I needed voltage of at least .025 and I use .05 with 2200 NB or 11x multiplier.
Forum: Memory 07-23-2010, 09:44 AM
Replies: 13
Views: 7,756
Posted By L4d
Add ~ .25 -.5 volt of CPU-NB/IMC.

Add ~ .25 -.5 volt of CPU-NB/IMC.
Forum: Memory 07-16-2010, 08:38 PM
Replies: 3
Views: 2,963
Posted By L4d
Try 2.1 volts to the RAM and add voltage to the...

Try 2.1 volts to the RAM and add voltage to the CPU-NB.
Forum: Memory 07-09-2010, 10:28 AM
Replies: 13
Views: 8,888
Posted By L4d
800mhz with CAS 4/4/4 is faster than 1066 6/6/6...

800mhz with CAS 4/4/4 is faster than 1066 6/6/6 so 1066 is unstable on your system unless you try higher clocks to your tRC and/or tRAS.
Forum: Memory 07-07-2010, 05:59 PM
Replies: 13
Views: 8,888
Posted By L4d
800mhz should be able to get CL 4, tRCD 4, and...

800mhz should be able to get CL 4, tRCD 4, and tRP 4.
If these are possible try next adding voltage then Command Rate 1. I doubt you'll get 8gb with Command Rate 1.
There are further adjustments...
Forum: Memory 07-07-2010, 05:44 PM
Replies: 13
Views: 8,888
Posted By L4d
RAM GUY is right. With AMD your lucky to get 1066...

RAM GUY is right. With AMD your lucky to get 1066 with 4gb!
I am unable to get 1066 stable with my AMD setups. With my Corsair Dominator 8500c5's and another brand of 8800 5-5-5-15.
Forum: Memory 07-07-2010, 05:39 PM
Replies: 4
Views: 3,269
Posted By L4d
Try command rate 1 @ 800mhz and 4-4-4. Is your...

Try command rate 1 @ 800mhz and 4-4-4.
Is your tRC able to get lower than 13?
Forum: Memory 07-04-2010, 12:21 PM
Replies: 13
Views: 8,888
Posted By L4d
Try 6/6/6/15/24 or 6/6/6/18/31 for 1066mhz.

Try 6/6/6/15/24 or 6/6/6/18/31 for 1066mhz.
Forum: Memory 05-30-2010, 02:53 PM
Replies: 7
Views: 5,988
Posted By L4d
Ganged may increase stability like T2 command...

Ganged may increase stability like T2 command rate?
Forum: Memory 05-27-2010, 09:33 PM
Replies: 14
Views: 19,786
Posted By L4d
Idea 20 hours Prime 95 Blend stable

This 720 X4 BE was doing 20 hours of Prime95 @ 3ghz, auto voltage, in BLEND with BIOS F10. I stopped this without errors.
Forum: Memory 05-27-2010, 05:29 PM
Replies: 7
Views: 5,988
Posted By L4d
I got a response from Gigabyte saying my 720 BE...

I got a response from Gigabyte saying my 720 BE cannot run dual channel 1066.
This is an AM3 processor so why doesn't it support 1066mhz dual channel?

I was told to use one stick of ram on my...
Forum: Memory 05-25-2010, 11:51 AM
Replies: 14
Views: 19,786
Posted By L4d
Response from Gigabyte

"Note: Due to AMD AM3/AM2+ CPU limitation, DDR2 1066 or above speed is only supported by 1 dimm per channel. Please run 1 module of 1066 memory on this board"

This is with GA-MA7LM-S2H:...
Forum: Memory 05-22-2010, 04:47 PM
Replies: 14
Views: 19,786
Posted By L4d
Is the +.1v needed to make your RAM stable?

Is the +.1v needed to make your RAM stable?
Forum: Memory 05-21-2010, 10:02 AM
Replies: 11
Views: 5,476
Posted By L4d
Does this mean that a Phenom processor or a...

Does this mean that a Phenom processor or a Phenom 2 may not run 1066mhz. I thought all Phenoms and Phenom 2's may run 1066mhz.
Forum: Memory 05-09-2010, 10:23 PM
Replies: 14
Views: 19,786
Posted By L4d
http://www.gigabyte-usa.com/FileList/MemorySupport...

http://www.gigabyte-usa.com/FileList/MemorySupport/mb_memory_ga-ma78lm-s2h.pdf

I cannot use my Dominators @ 1066 with this Gigabyte motherboard.
Forum: Memory 10-08-2009, 01:15 PM
Replies: 14
Views: 19,786
Posted By L4d
Perhaps this is not video card related since you...

Perhaps this is not video card related since you use Nvidia and I AMD.
Forum: Memory 10-01-2009, 11:15 PM
Replies: 14
Views: 19,786
Posted By L4d
There are 2 DIMMs for ram available on the...

There are 2 DIMMs for ram available on the http://www.gigabyte.com/products/product-page.aspx?pid=3193&dl=1#biosmotherboard.
800C, 5 tRAS, 13 tRC, and Command Rate 1T, 3 tWR, 2-4 tRTP, 2 tWTR, 2...
Forum: Memory 09-15-2009, 12:05 AM
Replies: 14
Views: 19,786
Posted By L4d
Thanks Ram Guy for your response! 105/75/75/75...

Thanks Ram Guy for your response!
105/75/75/75 is the lowest I can go.
Forum: Memory 09-14-2009, 02:45 AM
Replies: 14
Views: 19,786
Posted By L4d
Important Cycle Refresh Time or trfc

I got a pair of 2x2gb 1066 c5 Dominator running @ DDR2-800C dual channel Unganged (Ganged fails Prime95 after 58 minutes). CR 1, 105 and 75ns tRFC, tWR 3, tWTR 2, tRRD 2, and tRTP 2 @ ~2.1 volts.
...
Showing results 1 to 25 of 66

 
Forum Jump

All times are GMT -4. The time now is 06:46 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.