The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Showing results 1 to 25 of 10000
Search took 0.42 seconds.
Search: Posts Made By: c-attack
Forum: Cooling 01-25-2020, 11:47 AM
Replies: 1
Views: 27
Posted By c-attack
Certainly possible and the slow march to the...

Certainly possible and the slow march to the thermal shutdown point is the classic sign of a flow issue. If you have iCUE or Link installed, you can see the H100i v2 Temp (coolant temp). Anything...
Forum: Cooling 01-25-2020, 11:42 AM
Replies: 7
Views: 90
Posted By c-attack
Connector swap or even just disconnect and...

Connector swap or even just disconnect and re-connect is always the place to start. One rare occasions, we have seen one header on the C-Pro lock up. It always seems to be #1. It is not a...
Forum: Cases 01-25-2020, 11:38 AM
Replies: 1
Views: 36
Posted By c-attack
You may need to refine your parameters a bit for...

You may need to refine your parameters a bit for us. I can think of many cases where it will fit, but presumably you don't want a 1000D. The "mid-size" case is going to be tough across any brand. ...
Forum: Cooling 01-25-2020, 09:52 AM
Replies: 5
Views: 91
Posted By c-attack
This really shouldn't happen. Coolant changes...

This really shouldn't happen. Coolant changes should be relatively slow. If I ran a 100% CPU stress test, it might take 6-10 minutes for the cooler to reach +6-8C, which would still have you below...
Forum: Cooling 01-24-2020, 06:13 PM
Replies: 5
Views: 91
Posted By c-attack
As noted above, the preset curves were designed...

As noted above, the preset curves were designed for a 20-23 baseline temperature. You are warmer because of your case layout. Quite a bit warmer actually and perhaps that is something that we...
Forum: iCUE Software 01-24-2020, 11:53 AM
Replies: 11
Views: 272
Posted By c-attack
You won't and neither would I unless there is a...

You won't and neither would I unless there is a universal issue that then requires a fix. At this point, you are the only person reporting this "selective" fan detection. A BIOS level problem would...
Forum: iCUE Software 01-24-2020, 10:31 AM
Replies: 1
Views: 49
Posted By c-attack
I don't think so. All of the Settings from the...

I don't think so. All of the Settings from the top menu are universal across all profiles. Sorry, I can see where that might be useful.
Forum: iCUE Software 01-24-2020, 10:27 AM
Replies: 3
Views: 74
Posted By c-attack
Not really. Turns out a lot of people are bad at...

Not really. Turns out a lot of people are bad at math and cannot calculate 25% of 2000 rpm = 500 rpm. Ultimately, you want a specific RPM and not a specific PWM % anyway. It also deals better with...
Forum: Cooling 01-24-2020, 10:18 AM
Replies: 5
Views: 91
Posted By c-attack
I don't see a Commander Pro (Corsair fan...

I don't see a Commander Pro (Corsair fan controller), so I am assuming the H100i Platinum is the only CUE controlled fan device. It will take care of the two radiator fans. Fan speed is based on...
Forum: Cooling 01-24-2020, 10:10 AM
Replies: 7
Views: 90
Posted By c-attack
You will be fine with standard 2 way splitters. ...

You will be fine with standard 2 way splitters. Just pick one end or the other and start working you way across. For each radiator, 2 fans share a splitter. 3rd fan goes solo. That takes you up...
Forum: Cooling 01-24-2020, 10:06 AM
Replies: 8
Views: 75
Posted By c-attack
It isn't just about exceeding the current...

It isn't just about exceeding the current tolerate for a specific header. You may find that the controls simply don't respond right on 3 way splitters. You may also encounter issues trying to set...
Forum: Cases 01-23-2020, 11:27 PM
Replies: 1
Views: 48
Posted By c-attack
You won’t be able to do 2x280 with anything else....

You won’t be able to do 2x280 with anything else. Those two can do any of the three sides in combination, but not take a 3rd radiator (aside from a token 120/140). If you want three, you have to do...
Forum: iCUE Software 01-23-2020, 09:14 PM
Replies: 3
Views: 74
Posted By c-attack
All fans have a minimum speed. The ML should be...

All fans have a minimum speed. The ML should be around 400 rpm. The LL will be 600 rpm.

On the H115i Plat controls in iCUE, keep bumping up the % until you find the start trigger. Most fans are...
Forum: iCUE Software 01-23-2020, 07:07 PM
Replies: 2
Views: 78
Posted By c-attack
1)The prior generation Asetek partner coolers...

1)The prior generation Asetek partner coolers would display half the pump speed. If it is displaying erratic or doubled up values, it is likely a software reading problem. Make sure you have set...
Forum: Cooling 01-23-2020, 06:57 PM
Replies: 2
Views: 48
Posted By c-attack
Good chance it will be since both the H100x and...

Good chance it will be since both the H100x and H100i XT have the same OEM partner. Not all Corsair coolers can utilize the same backplate bracket, but chances are these two can. That said, the XT...
Forum: iCUE Software 01-23-2020, 05:20 PM
Replies: 2
Views: 57
Posted By c-attack
Can you confirm you are on the proper software...

Can you confirm you are on the proper software profile and iCUE is running when this happens? It is theoretically possible for the actions list become corrupted, overwritten, or something similar,...
Forum: Keyboards and Mice 01-23-2020, 04:04 PM
Replies: 4
Views: 80
Posted By c-attack
Yes, unfortunately the side thumb rest is not...

Yes, unfortunately the side thumb rest is not removable on the Nightsword. However, while I disliked it on the Glaive, I find it comfortable on the Nightsword. Not sure where you are located. In the...
Forum: Memory 01-23-2020, 11:15 AM
Replies: 1
Views: 50
Posted By c-attack
When you put your PC into S3 sleep or other...

When you put your PC into S3 sleep or other standby modes, the system state is stored in the RAM. You can't remove power to it like a normal LED. The easiest solution is to set the system to...
Forum: Keyboards and Mice 01-23-2020, 11:11 AM
Replies: 4
Views: 80
Posted By c-attack
The Nightsword might be comfortable. It is...

The Nightsword might be comfortable. It is middle sized, with a natural set-up for palm grip, but also works with a semi-claw or finger tip....
Forum: iCUE Software 01-23-2020, 11:02 AM
Replies: 4
Views: 97
Posted By c-attack
Yes, if you connect the fan wires to the...

Yes, if you connect the fan wires to the Commander Pro instead of the cooler, then their speed will register on the C-Pro. There is nothing connected to the cooler, so 0 rpm.

You probably want...
Forum: Hydro X Custom Cooling 01-23-2020, 10:52 AM
Replies: 14
Views: 178
Posted By c-attack
It is an OEM replacement part and likely only...

It is an OEM replacement part and likely only available through Corsair -- other than in the ML140-RGB form, but that is changing the game a bit. Regardless, you could compare the ML140 OEM part...
Forum: Cooling 01-23-2020, 10:46 AM
Replies: 6
Views: 104
Posted By c-attack
It should run faster than that for your specified...

It should run faster than that for your specified curve. Click the Fixed % and set it to 75% to see if it responds.

Aside from that, the previous question about other monitoring software is still...
Forum: Cooling 01-23-2020, 10:41 AM
Replies: 4
Views: 98
Posted By c-attack
I don't think you will find any performance...

I don't think you will find any performance difference between a ML120 and NF-F12 of any flavor. The industrial 2000 or 3000 rpm version only has a statistical advantage when you are running at...
Forum: Cooling 01-22-2020, 10:36 PM
Replies: 2
Views: 51
Posted By c-attack
You are trying to get the inlet/outlet tubes...

You are trying to get the inlet/outlet tubes above the CPU block so the bubbles float up and out of the pump. For most installations, that means lifting the front of the case and so measure of...
Forum: Hydro X Custom Cooling 01-22-2020, 08:54 PM
Replies: 2
Views: 62
Posted By c-attack
No and the Hydro X curves definitely are not...

No and the Hydro X curves definitely are not programmed for balance. It is strictly a radiator/cooling specific calculation. This is one of several reasons why I don't advocate for zero rpm use. ...
Showing results 1 to 25 of 10000

 
Forum Jump

All times are GMT -4. The time now is 02:30 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.