Jump to content

TheTiesThatBind

Members
  • Posts

    117
  • Joined

Reputation

10 Good

About TheTiesThatBind

  • Birthday August 12
  1. Thanks! I was looking at it as well, but was afraid that I could be wrong and I didn't want to mess anything up :D This cable is enough for a 4080 right? Wattage wise I mean.
  2. Hey everyone, I'd like to ask if the product with the following code "CP-8920284" will be suitable for my Corsair RM750x PSU (2018) version. Kind regards!
  3. Exactly the answer I was looking for. On as always C! You helped me in the past to understand coolant temp as back then I was only familiar with CPU's package temp. Anyway, I replaced the thermal compound with Thermal Grizzly's one and moved the AIO from top to front . Now, there's only 1 core peaking at 95oC with just XMP enabled in a 10 min. I've also added the included fans (AF Elite) of the cooler so I'm running a Pull/Push configuration. I don't know if that's wise as the amount of air moved from the AF Elite series is higher than ML series (I think at least) but gets the work done I suppose. I tuned the RPMs to be at the same range. Now I get like 80-90oC to all P-cores expect that one I mentioned reaching 94-95oC with no power limits enforced. E-Cores run at about 75oC I think. I wonder what settings should I change in my BIOS for the CPU to run at its Intel specification and make it run with lower voltages compared to the stock which is about 1.3-1.35V. My room temp is between 19.5-20.5oC (I measured it again :D ) and the coolant temp now is 32.6-32.8oC. I was worried cause i didn't have no problems at all with my 9900K and the H115i Pro. I had no clue that those chips run so hot. All measurements took place with the tempered glass side panel off.
  4. Shouldn’t the coolant temp stabilise after a while though? I mean it seems a bit unreasonable to just keep climbing up no? Would I see any difference if I front mount the cooler and/or if I also use the included AF ELITE fans plus the ML fans in a push / pull configuration?
  5. Those coolant temps, they were just keep going up, never stabilized and I have fans running at 100% at 38oC (!) for 5mins of Cinebench R23 are unreasonable high. Also it reports as XT (No clue why).
  6. Also my AIO's coolant temp idles between 34-35oC which is unreasonable high while package is at 40oC. Ambient temp is around 21oC.
  7. Hello everyone! I'm facing troubles with my brand new Corsair iCUE H150i RGB Elite. So I'm running an Intel i7 13700K. I tried to stressed it running Cinebench 23 and the coolant temp went as high as 39 degrees (while package hit 97oC on the hottest P core). This, to me, seems abnormal. Is my cooler defective? Should I try using Thermal Grizzly's contact frame? I had the side panel off btw. The cooler is mounted at top while 2x140mm ML Fans bring the air inside the case. Only XMP profile is enabled. PS. This is a 2nd CPU, I RMAd the previous one which was also ran hot (100oC) without even XMP enabled, instantly (hits it). Hopefully somebody can help me out Kind regards
  8. Since it works fine without adding VoiceMeeter etc on the headset, is it normal for this specific headset that the mic picks up the sound of the headset? I've played a YouTube song and ran a record on Audacity and I can notice the music playing on the background.
  9. Alright thank you! Well, I can get them play fine w/o the Banana VoiceMeeter but I can't get them work correctly with it for some reason as the mic reproduces the sound to Discord etc.
  10. Okay, sorry for double posting. I performed a clean install of Realtek drivers by removing them through DDU and static noise is gone while listenting to myself while talking to mic as well. Though, mic default volume @ 44 is too low and if I move it all the way up to 100 the mic picks up the headset's sound as well as even nothing plays on PC the Microphone bar on Sound Control Panel moves a bit up and down. Any suggestions about that? My mobo is ASUS Prime X370 Pro and I already used Separate all input jacks option. What else shall I do? Shall I activate Noise Cancellation and AEC? What about bit? Which Hz & Bit shall I use for both the mic and headset?
  11. Well yesterday I got my brand new Corsair HS50 and I'm facing some issues. If I get the sound bar at max, I get static noise while on about 50% of it it's perfectly fine and of course I have always maxed out the volume of Windows. Then, if I speak too loud or bring the mic close to my mouth and talk, I can hear myself through the headset despite having the listen to this device disabled on control panel. Only thing that runs on the headset is an EQ through APOEQ from rtings which shouldnt cause any trouble whatsoever. So what's going on with my headset? Any clues/solutions? Kind regards
  12. Why sometimes my Spiral Rainbow RGB effect applied on my keyboard appears to be laggy? Any solutions? Kind regards Rest of my iCUE Devices are using solid color.
  13. Good evening, happy holidays everybody! I would like to ask if the RGB fans included with the 220T case are PWM controllable. Kind regards
  14. Thanks C! Well I’m using low rpm curve during light desktop work and speed up the things while on gaming so i guess I should try to do a separate fan curve for summer then
  15. Room temp during winter is ~ 20C(Max), May to June and September is about 24-30 depending the temp outside
×
×
  • Create New...