Jump to content

p2im0

Members
  • Posts

    11
  • Joined

Reputation

11 Good

About p2im0

  • Birthday 10/15/1986
  1. FYI the way I ended up fixing this was disabling "CorsairLink and Asetek support" in HWINFO64. I'm not sure how it got re-enabled, but doing that in combination with hard-reset the Commander Pro, and completely wiping out iCUE and all settings and I have it working again. Still frustrating.
  2. GIF of what happens when I update firmware in v4 iCUE. Some fans show up for a second and poof, disappear again. (sped up the firmware update time to fit as a GIF)
  3. [X-posted my comment from the Release Notes Thread] I have a Commander pro, corsair fans attached, and an XD5 attached. Everything has worked fine for 2+ years. I just updated iCUE in place to 5.1 and it lost all fans and my XD5 connected to my commander pro. I have a separate flow sensor/alarm that immediately started going off when my pump stopped spinning. I cannot seem to get the new iCUE to detect my fans or pump. When I force a firmware update on my commander pro they're detected for a second and I get a message "iCUE has updated 1 module: COMMANDER PRO" and then they disappear and my pump stops working again. I just downgraded to v4.33.138 and I now have the same issue. No voltage reported, all fans and pump missing from my Commander Pro. They spin up full speed for a second when I force a Commaner Pro firmware update and then disappear from the app. NOW WHAT?! Fans & Pump show up for 5 seconds after a force of firmware update on commander pro Not working on v4.33.138, after the in-place upgrade to 5.1
  4. I have a Commander pro, corsair fans attached, and an XD5 attached. Everything has worked fine for 2+ years. I just updated iCUE in place to 5.1 and it lost all fans and my XD5 connected to my commander pro. I have a separate flow sensor/alarm that immediately started going off when my pump stopped spinning. I cannot seem to get the new iCUE to detect my fans or pump. When I force a firmware update on my commander pro they're detected for a second and I get a message "iCUE has updated 1 module: COMMANDER PRO" and then they disappear and my pump stops working again. I just downgraded to v4.33.138 and I now have the same issue. No voltage reported, all fans and pump missing from my Commander Pro. They spin up full speed for a second when I force a Commaner Pro firmware update and then disappear from the app. NOW WHAT?! Fans & Pump show up for 5 seconds after a force of firmware update on commander pro Not working on v4.33.138, after the in-place upgrade to 5.1
  5. I just updated to iCue 4.12.214 and this issue still exists. After every reboot all of my Fans and Pump using the HydroX profiles are reset to "Quiet".. Only way to fix is to change start-up to launch icue.exe instead of icue launcher.exe...
  6. doing this actually didn't resolve it for me. I changed my startup app via regedit under HKEY_LOCAL_MACHINE (as it's installed for all users). Today I rebooted and all my fans and pump that were using HydroX Fan and Pump profiles were set to Quiet profile again. If I quit iCue and relaunch via the iCue.exe executable shortcut on my desktop it lets me re-choose the HydroX profiles for pump and fans.
  7. Glad I found this thread. I'm having the same issues - Commander Pro & Lighting node pro -after every reboot since 4.11 my pump resets to the quiet profile. It seem to use the hardware profile until I manually open iCue after a reboot - when I manually open it I can hear the pump slow down. This definitely did not happen with earlier versions of iCue 4.XX As soon as I manually launch, pump is in Quiet mode (running only 1300RPM or so) and the HydroX wizard button actually disappears. I've been fixing this every reboot by running the installer and clicking repair install. Going to check out the task scheduler change noted above.
  8. I ended up having the same thing happen and ended up with a 3090 I couldnt say no to. But man I really want to see the 6900XT succeed... and kinda want one just to test. But a water block is absolutely necessary for my build.
  9. Anyone seen more news of a targeted ETA for the XG7 3090 FE block? Same situation as you guys, air cooled 3090 waiting for a block.
  10. I just re-built my setup with a HydroX loop with 5 LL120 fans connected to a Commander Pro. Setup iCue and got it all working, but I have one fan that intermittently disagrees and will not be controlled by iCue. This has happened consistently after reboots. All ports on the Commander Pro are set to 4-pin in the Settings page, and the pump is on port #6. I had all fans set to the HydroX Fan Profile (which had them at 0RPM) yet this bugger decides to do its own thing. It'll also sometimes decide to stop spinning while all the others are spinning. Anything I should check before attempting an RMA?
×
×
  • Create New...