acsrand

Tried installing the Corsair iCue update FW 1.0.4, just hangs and if I select abort it says my iCue will be in an inoperable state!

c-attack, to refresh: my sys has 4 system fans (excluding the Graphics card fans and H150 CPU cooler fans). iCue is reporting for the MOBO 3 fans (1, 2 and 3). iCue Fan 1 = my Rear Fan SysFan1 iCue Fan 2 = my bot. Fan SysFan2 iCur Fan 3 = some phantom fan! My two front fans (MOBO SysFan#5 FrontTop and MOBO SysFan#6 FrontBot are not reported!)

c-attack, well I did as you suggested. I unplugged the 2 front fans and no changes noted on iCue Dashboard! I then unplugged SYS_FAN2 (Bottom Fan) and iCue showed that the #2 fan speed as 0. It is extremely difficult to get to the rear fan plug, it took nearly 30 minutes the 1st time I installed it and I had to use a set of forceps to install it. So I am not going to go through that pain just to try and figure out what iCue is doing. Some thing is very screwed up with the iCue reporting. Since iCue is only reporting 3 MOBO fans, and I know know it is not reporting the front fans, something is screwed up since it is reporting a MOBO fan that must either be associated with the iCue radiator or the GeForce graphics card, or who knows what. And before you ask, the 3 MOBO fans iCue is reporting are all running a different speeds (according to iCue) so there is know way the iCue is reading one fan and showing it as a second fan. There has got to be someone at Corsair who understand the iCue and can provide me with some info. to resolve my issue. Are you a paid rep. of Corsair?

Ok, for now here is the info. for the fans: Phanteks 140mm fans (4ea) PH-F140XP_BK.

C-attack, if you look at the information I provided on the 12th Jan at 5:35PM, the attached file shows all fans in my system and the header they are connected to. I will explain once again (see attachment from 12 Jan): excluding the Graphics card and the H150i radiator fans, the system has 1 Rear Fan exhaust fan [header Sys_Fan1/2/3/4], 1 Bottom inlet fan [header Sys_Fan1/2/3/4], 2 Front intake fans [header Sys_Fan5/6_Pump]. iCue dashboard only shows 3 fans for the MOBO, there should be 4. The iCue does not provide any information about which fan it is reporting for the MOBO, therefore I cannot tell you which 3 of the 4 fans the iCue is reporting.

c-attack, you never responded to "how will I find out the outcome of the Bug Report investigation" Please reply.

c-attack Thanks for the info., BIOS is vF10. How will I find out the outcome of the Bug Report investigation? it will be a few weeks before I try the additional temp. sensors. Good memory regarding the GeForce graphics card, I had forgotten the details.

c-attack, one more item, my GeForce RTX 2080 has 3 fans, iCue only displays info. about 2 of the 3 fans.

C-attack, ok updated the iCue to V3.24.52 (see attached) and deleted / added back in the MOBO iCue monitoring. There is nothing special about the Fan connections, as shown in the prev. attached, ALL fans connect separately to a header on the MOBO i.e. not driving any of the fans via a split cbl or hub etc. (and I can see them in my BIOS setup). Also, I am about to add to additional thermistors to my system and connect to my MOBO. So any info. on how to get iCue to display the measurements from these added thermistors would be helpful.

C-attack: iCue v3.18.77 see attached fan / MOBO definition and iCue dashboard

C-attack, then what is this if not the version number (see attached)? Why does the iCues program ability to understand my MOBO change from boot to boot?

icue v1.0.4 not reporting all my case fans i.e. not reporting fans connected to my MOBO (only reporting 2 of the four case fans) PS-Corsair Tech told me not to upgrade my icue from v 1.0.4 so that is the reason I am using an older version of icue

Latharion and C-attack, again thanks for the input, you both were very helpful. I will go do more research and maybe come back with some additional questions.

Here is an attached copy of the data file with detailed time ticks.Redcued data GORT1 H150i iCUE temps 21oct19.pdf

c-attack, btw, I meant to include the more ganular timing. If your interested I could redo the pdf and attach a version with detailed time ticks. Let me know if this is of interest to you.