tjgodin Posted April 28, 2019 Share Posted April 28, 2019 Note, I don't work for Corsair however I thought it would be good to start a feedback thread of issues that perhaps still persist for forum users since the 3.15.101 release. You may wish to note some of your configuration details, such as motherboard, etc... Best regards, Tony Link to comment Share on other sites More sharing options...
tjgodin Posted April 28, 2019 Author Share Posted April 28, 2019 Upon windows startup, after login, when the iCUE program is activated I hear the USB disconnect sound as the software initiates the iCUE application. I have a Commander Pro connected to the motherboard USB header, with my H100i AIO connected via the USB port on the Commander Pro. I also have a HX750i power supply connected via USB for monitoring in iCUE. Its unclear if it is the Commander Pro which is disconnecting or one of the other devices. The disconnect only occurs on the first launch of the iCUE software. If I close the application and restart during the same windows session, no disconnect occurs. I'm using an ASRock Z390 Phantom Gaming ITX/ac motherboard with Window 10 Pro x64 (1903) installed. Tony Link to comment Share on other sites More sharing options...
mtveness Posted April 28, 2019 Share Posted April 28, 2019 This update was a mistake. I have it setup to show data from the H115i Pro, Intel 7700K, MSI Z270 SLI & GeForce GTX 1060. Three of them seem to be right. But the MSI MB data has changed. One of the case fans shows up inconstantly and always reads zero. I can see it is running and the MSI software shows a speed of over 500rpm. And I have picked up two temps only in iCUE Space that do not exist. "CPU #1" and "System #1" always show the same static temp. Fortunately it looks like the profiles and what they control were not affected. I did the software repair through uninstall routine without any luck. The last time this happened on an update I had to uninstall/reinstall. This is soooo much fun on a multi-user computer. You have to import all the profiles. And you have to do it logged in under each user separately. Link to comment Share on other sites More sharing options...
viatorium Posted April 28, 2019 Share Posted April 28, 2019 I've had no issues w/ the new update (3.15.101) but i haven't had a chance to test out if the steam/platinum cooler conflict issue has been resolved as was previously mentioned. The fix date was the 22nd as per what I read. Anyone else having this issue still? It'd be nice to have a feature roadmap made available as well but I'm sure that's unlikely. Link to comment Share on other sites More sharing options...
P33R Posted April 28, 2019 Share Posted April 28, 2019 Ive been through many, many updates with iCue and never had any problems, until now (not a big one though) It seems that the function "Play on pressed key" in the gradient lighting effect does not have any effect. I have it set across all my keyboard keys to light the key ive pressed for 3 seconds in red. Its configured as "Start: On key pressed, play on pressed key, Stop: After 1 time" In the newest version ALL my keys light up, regardless of wich one i press. I tried re-doing the gradient effect and the whole lighting setup for the keyboard, doesnt work. Ive installed the previous version again, and it works just fine there. My keyboard is a K70 RGB MK.2 its obv not a big deal, but maybe other people have the problem too. Doesnt seem to have any other problems for me. Sabre RGB mouse, VOID wireless, MM800, ST100, H150i Pro, commander pro and lighting node pro all work fine. Its my first post here, so sorry if im forgetting something/doing something wrong. Will quickly answer to any question. Link to comment Share on other sites More sharing options...
Isthar Posted April 28, 2019 Share Posted April 28, 2019 I opened a thread yesterday as some functionality has gone with this update. It is not longer possible to set different lighting effects to each RGB zone of the Dark Core SE. The Lighting Effects doesn't show the + button to add different configurations, so you can't set different effects to each zone of the mouse. Link to comment Share on other sites More sharing options...
Josey Wales Posted April 28, 2019 Share Posted April 28, 2019 I just purchased my last Corsair Product, You people cannot even provide Release Notes? I am having problems that seem to be related to my M65 Mouse and this Poor software! Link to comment Share on other sites More sharing options...
tjgodin Posted April 28, 2019 Author Share Posted April 28, 2019 Given they did post notes for v3.14.104, I'm sure they should hopefully be forthcoming. This update was just released end of last week, so fingers crossed they will early this coming week. I agree you'd think they'd follow the availability of the update immediately, but we don't live in a perfect world either. Link to comment Share on other sites More sharing options...
Josey Wales Posted April 30, 2019 Share Posted April 30, 2019 Given they did post notes for v3.14.104, I'm sure they should hopefully be forthcoming. This update was just released end of last week, so fingers crossed they will early this coming week. I agree you'd think they'd follow the availability of the update immediately, but we don't live in a perfect world either. A week without release notes of any kind is not acceptable. Link to comment Share on other sites More sharing options...
Fistsojustice Posted April 30, 2019 Share Posted April 30, 2019 A week without release notes of any kind is not acceptable. I dont think corsair really KNOWS whats in the update...lol Their just stomping out spot fires while breaking new things. Link to comment Share on other sites More sharing options...
Djiddy Posted April 30, 2019 Share Posted April 30, 2019 8% CPU charge on i9 9900k??? Link to comment Share on other sites More sharing options...
rocsen Posted April 30, 2019 Share Posted April 30, 2019 (edited) I have this same problem so +1 Windows 7 64 bit Asus Maximus VIII Corsair R750i and H115i Pro connected to Commander Pro via m.board USB header Upon windows startup, after login, when the iCUE program is activated I hear the USB disconnect sound as the software initiates the iCUE application. I have a Commander Pro connected to the motherboard USB header, with my H100i AIO connected via the USB port on the Commander Pro. I also have a HX750i power supply connected via USB for monitoring in iCUE. Its unclear if it is the Commander Pro which is disconnecting or one of the other devices. The disconnect only occurs on the first launch of the iCUE software. If I close the application and restart during the same windows session, no disconnect occurs. I'm using an ASRock Z390 Phantom Gaming ITX/ac motherboard with Window 10 Pro x64 (1903) installed. Tony Edited April 30, 2019 by rocsen Link to comment Share on other sites More sharing options...
rocsen Posted April 30, 2019 Share Posted April 30, 2019 The pump on the H115i Pro is set to Quiet but would randomly jump to Balanced. I can only tell because I can hear the pump suddenly ramp up the rpm. iCUE shows it jumping between 1080 and 2000rpm When I run Link it doesn't happen. Link to comment Share on other sites More sharing options...
c-attack Posted April 30, 2019 Share Posted April 30, 2019 The pump on the H115i Pro is set to Quiet but would randomly jump to Balanced. I can only tell because I can hear the pump suddenly ramp up the rpm. iCUE shows it jumping between 1080 and 2000rpm Randomly? Or at a specific coolant temperature? Link to comment Share on other sites More sharing options...
Djiddy Posted April 30, 2019 Share Posted April 30, 2019 Randomly? Or at a specific coolant temperature? Not astounding refferring to my post. 8% CPU charge on i9 9900k??? Link to comment Share on other sites More sharing options...
rocsen Posted April 30, 2019 Share Posted April 30, 2019 Good question. I just ran Prime95 and the pump does then jump to 2000rpm In Link the pump would stay at 1000rpm when set to quiet. Is there a way to lock it to 1000rpm in iCUE? One more thing, in Link if I choose one of the default fan profiles (quiet, balance, performance) I can still change the temp sensor source. In iCUE this doesn't seem to be possible. And one suggestion. It would be very helpful to access fan/pump profiles from the dashboard. Again this is possible in Link and reduces a lot of clicking and back and forth. For now I'm sticking with Link. Link to comment Share on other sites More sharing options...
Djiddy Posted April 30, 2019 Share Posted April 30, 2019 Sorry Corsair but I would like a PC silent at idle. I paid 3500€ for a gaming PC! Link to comment Share on other sites More sharing options...
P33R Posted May 1, 2019 Share Posted May 1, 2019 (edited) 8% CPU charge on i9 9900k??? That doesnt sound right, i have a 9900k too and 9 devices in iCue, all with various lighting effects and the service is around 1% usage +/- 0.5 Edit: Forgot to mention i went back to 14.104...did you have this with 14.104 too or just with the newest version? Edited May 1, 2019 by P33R Link to comment Share on other sites More sharing options...
BlaiseP Posted May 1, 2019 Share Posted May 1, 2019 8% CPU charge on i9 9900k??? That doesnt sound right, i have a 9900k too and 9 devices in iCue, all with various lighting effects and the service is around 1% usage +/- 0.5 Edit: Forgot to mention i went back to 14.104...did you have this with 14.104 too or just with the newest version? I just checked mine: 9900k / EVGA Z370 Classified K / 2 x Commander Pro / 4 x RGB strips / Vengeance RGB RAM / AX1200i / K95 Platinum / M65 Pro RGB... CPU usage 0.4~0.8% ("Enable full software control" is disabled for the RAM in ICUE v3.15.101) Link to comment Share on other sites More sharing options...
DevBiker Posted May 1, 2019 Share Posted May 1, 2019 8% CPU charge on i9 9900k??? Do you have full software control enabled for the RAM? If so, uncheck it. The effects won't be as good but CPU usage should drop. This is a known issue and one that Corsair is working on. Link to comment Share on other sites More sharing options...
zeroXII Posted May 1, 2019 Share Posted May 1, 2019 My LL120 fans do not light up on PC boot after a shutdown. For some reason, iCue doesn't save the lighting settings on my Lightning Node Pro even though its detected upon system bootup. Everything else seems fine though. My H100i Platinum and Vengeance RGB Pro all light up as intended. Annoying to have to keep opening up iCue and manually set the lighting up for my fans upon every PC startup. Link to comment Share on other sites More sharing options...
schangtil Posted May 1, 2019 Share Posted May 1, 2019 There is still errors in current measurements for the AX1600i, 3A on ports not connected to anything. Link to comment Share on other sites More sharing options...
rocsen Posted May 1, 2019 Share Posted May 1, 2019 I managed to resolve the USB sound which I think is actually a connect sound, by connecting the AIO directly to the motherboard USB header. Upon windows startup, after login, when the iCUE program is activated I hear the USB disconnect sound as the software initiates the iCUE application. I have a Commander Pro connected to the motherboard USB header, with my H100i AIO connected via the USB port on the Commander Pro. I also have a HX750i power supply connected via USB for monitoring in iCUE. Its unclear if it is the Commander Pro which is disconnecting or one of the other devices. The disconnect only occurs on the first launch of the iCUE software. If I close the application and restart during the same windows session, no disconnect occurs. I'm using an ASRock Z390 Phantom Gaming ITX/ac motherboard with Window 10 Pro x64 (1903) installed. Tony Link to comment Share on other sites More sharing options...
aska Posted May 1, 2019 Share Posted May 1, 2019 Hi Corsair®, Please fix the flatlining custom fan curves asap, thanks. Link to comment Share on other sites More sharing options...
Josey Wales Posted May 1, 2019 Share Posted May 1, 2019 What Release Show me a download link or release notes? This is a deceptive practice calling a patch without a download a release?? Link to comment Share on other sites More sharing options...
Recommended Posts