Jump to content
Corsair Community

Search the Community

Showing results for tags 'macbook memory'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


    • Community Rules & Announcements
    • Live Event Announcements
    • New Product Releases
    • Non-CORSAIR Tech, Benchmarks, and Overclocking
    • Games & Gaming
    • Battlestation and Build Showcase
    • iCUE Software Troubleshooting
    • Build Hardware Troubleshooting
    • Gaming Peripherals & Audio Troubleshooting
    • Furniture and Ambient Lighting Troubleshooting
    • CORSAIR Pre-Built Systems Troubleshooting
    • Build Hardware
    • Gaming Peripherals
    • Audio Devices
    • Battlestation Hardware: Ambient Lighting, Furniture, etc.
    • CORSAIR Pre-Built Systems
    • CORSAIR Technologies Q&A
  • Alternative Languages
    • Deutscher Support (German Support)
    • French Support
    • Spanish Support
    • Corsair Enthusiasts Section
    • Corsair Product Discussion
    • Alternate Language Support
    • Customer Service


  • System Build Inspiration
  • Memory
  • Cases
  • Maximizing Performance
  • Peripherals
  • Storage
  • Liquid Cooling
  • Gaming Mice
  • News and Events
  • How-tos and DIY
  • USB Drives
  • Extreme OC Mods
  • Gaming Keyboards
  • Power Supply Units
  • Gaming Headsets
  • Uncategorized

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start



About Me



Optical Drive # 1







Found 1 result

  1. This blog is going to show you how easy it is to upgrade your Apple® MacBook® Pro to 8GB of memory. The total time to upgrade your MacBook’s memory is under 10 minutes. I used a MacBook Pro 17-inch mid-2010 model, and upgraded it from its current 4GB kit to a Corsair 8GB Mac Memory kit. To upgrade your MacBook's memory you will need a Phillips #00 screwdriver as the screws are very tiny. Start off by unplugging your MacBook Pro from the power source and anything else it may be connected to. Then place it upside down on a surface that will not scratch the lid of the laptop. Now carefully remove the ten Phillips head screws circled in red. It is important that you keep track of where each screw goes, as there are three different lengths of screws. Below you can see I laid out each screw according to the hole that it belongs in. Once all the screws have been carefully removed you can now remove the bottom cover. The cover will come off fairly easily. You can use your finger nail to get under the cover and lift up in an even manner. You should not use a screw driver to pry the cover off as you will scratch or damage the laptop. Now that the cover is off you can set it aside. Before touching any of the internals of the laptop you should touch the metal exterior of the laptop to ground yourself. The area circled in red would be a good area to ground yourself. As you can see this MacBook has already been upgraded with a Corsair Force Series™ SSD however the memory has not been upgraded. The memory modules are located near the center of the laptop. To remove the first module, gently push the levers circled in red outwards. The memory module should then pop up at an angle. Gently grab the sides of the module (circled in red). You can now remove the module from the slot by pulling the module towards you. Do not try to lift the memory upwards as that may cause damage to the slot and the memory. Now that the first module has been taken out you can remove the second module following the same procedure. Note that the levers for the second module may be hard to see, as the first set of levers are directly above them. After both of the old modules are out of the machine, line the notch (circled in red below) in the new module up with the memory slot. To insert the new module you will need to slightly angle the module similar to when you released the levers. Once the module is inserted into the slot gently push down on the module to lock it in place. Finally repeat the same process to put the second module in the top memory slot. Now you can place the cover over the bottom of the MacBook and tighten all of the screws down. Finally check that all of the memory is being seen by going to “About this Mac”. If it looks like the image on the right below, congratulations! You have successfully upgraded your MacBook's memory.
  • Create New...