Search the Community
Showing results for tags 'fan speeds'.
Hello Corsair users!!!! I have just done a new build and am fairly new to the corsair rgb and fan ecosystem. The build is a 465x case with the RGB Lighting node core and I have installed a commander pro as well. The mobo is a asus ROG strix x570-e gaming cpu= amd ryzen 7 3700x gpu= zotac gaming gforce rtx 3060 ti psu= evga superNOVA 750ga 80+gold. I have 4 LL120 3 in the front of case and one as rear exhaust then 2 QL120 on the top of the case as exhaust. i have learned reading through a bunch of post that you cant mix fans with the RGB Lighting node core. so my question is can you run 2 corsair rgb Lighting node cores off 1 commander pro with each rgb Lighting node core controlling only a set of LL or QL fans? Question 2!! This issue seams to be one with either Icue software or my commander pro. so what is happening is that what ever fan is plugged into port 6 wants to spin at 2300 rpm. I have tried multiple fans a different LL120 a QL120 and a non corsairs branded fan to take out the variable. They all sadly spin up to 2300 rpm Icue says and sound like a jet is taking off. I see for the specs of the LL and QL that they are only suppose to be 500-1500 rpm roughly so getting 2300rpm cant be good.......:bigeyes: The logical thing would be go to the icue software and adjust the speed. the problem is that majority of the time the software doesn't change any of the speeds. I will have to do a full reboot of my PC and sometimes and i will get lucky that they change. I can get port 6 to match the other fans if its on quite mode vs all the others being on extreme but it shouldn't be that way. It should be even across the board right??? I look in my open hardware monitor and it says that fans 1,3, and 4 only get 60%. these fans would be bottom front intake LL120 Top font intake LL120 and top of case exhaust QL120. So anyone know what could be the issue here do i need a new commander pro or are there some settings hidden in a windows PC or is it the mixing of types of fans???? I really hope someone can help me with this cause it is so frustrating...... Thank you for you time!!!! suggestion for Corsair software developers- make it so you can control either ll or ql fan by telling what fan is in each port on the same Lighting node core
I have 6 LL RGB fans and 4 temp sensors connected to a Commander Pro. The 3 default fan Performance Profiles are present and run as described. I've created new profiles b/c the Quiet one included runs too high and too often. However, the iCUE software will not apply any RPM settings lower than the Quiet one (~1000 RPM). Although I CAN create a ZERO RPM profile and can apply it, shutting down any/all of the case fans. Additionally, when I create a new fan profile, I point it at one of the various temp sensors as mentioned in previous posts. I have read several of the previous related posts, however, none seem to address this issue or offer any solution that has worked so far.
Help! I can’t control the fan speeds of my h100i platinum se! Alright so I’ve got myself a bit of an issue, I switched cases to a 465x to vastly improve airflow and looks of my computer, and I also bought a h100i platinum se to add to the RGB goodness. When I first put it together I attached the radiator to two of the front three intake fans and mounted the included cooler fans as an outtake, however I made a mistake, I attached the power connectors for the outtake fans to the pump to draw power from, I already had ICUE installed to color my k70 and void pro, and I was able to control the fan speeds of the fans connected to the pump, however I noticed that only the outtake fans were affected. I checked the wiring and swapped the power connectors so that the proper fans were connected to the pump. This is when things went awry. When I tuned the computer on after I switched the power cords, the outtake fans that are now connected to the mobo instantly pushed themselves up to full boar, causing a loud and annoying noise, I can change that in the bios and this is where why first question comes in, how do I do that? The next problem I encountered was my inability to control the fan speeds of the fans attached to the radiator. Then the final problem was ICUE not correctly displaying the cpu temp. All the cords are connected properly and I’ve double and triple checked them. The RGB works fine. How do I resolve these issues? TL,DR: I can’t control the fan speeds of the fans attached to my radiator of my h200i, when different fans connected to the pump I was able to control the speeds of. All the connections are sound.