Search the Community
Showing results for tags 'error codes'.
Howdy, Been using my corsair one i140 (9700K/2080/32GB/480GB M.2 SSD/2TB HDD) for a few years now and I'm here seeking some help/advice on how to resolve this error message/LEDs. When my CPU temp reaches around >50C, the top fan starts to erratically spin very high then stop spinning. Usually when this happens the LEDs on the front of the desk top start flashing red patterns. Looked into the FAQ of what it means, but 'pump failure' or 'driver error' doesn't personally help me much. The LED patterns vary from 1st left blinking red 2nd right, and vice versa which leads me to believe I'm having both errors listed here : https://help.corsair.com/hc/en-us/articles/360025312012-CORSAIR-ONE-LED-Error-Conditions-Auto-Detection-of-Pump-Failure-or-Overheating I've been semi-ignoring this issue since I was able to temporarily bypass the annoyance with setting my fans to 'extreme' on iCUE. While on 'default', this error starts to come up consistently. Since summer is approaching though, I think this could be a thermal issue that I should no longer ignore. My first attempt to fix this was to simply clean out the radiators and the top fan. Opened up the desktop and gave it a good blasting of compressed air. Still came across the error instances though with mild pc usage. My second attempt which I will attempt tomorrow is to see if any cable has gone loose. I don't know what else to try, not extremely savvy with how to trouble shoot this pre built beauty. I can provide more info if needed, hoping I'm not the first to ever experience this. I have not done any sort of exploring in the BIOS or updating any sort of driver. Only updates I have done is through the Corsair Diagnostics app that came pre installed. Really hoping for some assistance. Thanks in advance!
I seem to be having problems trying to put an rgb effect my new Corsair iCUE H100i ELITE CAPELLIX and iCUE SP120 RGB PRO fans they are all connect to the commander core and in the new iCUE 4 it comes upas unknow device but if click on to it says commander core. all The leds are working because they are flashing red which I have researched and it apparently means that ether the pump isn't working or it overheating. Now I did have a problem when i first installed it with other heating because I put the fans on the wrong way but now I have sorted that and the pump is definitely working and I am not having any heating issues so I was wondering why the leds are still flashing red and why I can't change the rgb on them. I have tried uninstalling and re installing hence the newest version of iCUE. Any help would be greatly appreciated
Pc specs: 8700k X hero 1070 Dominator platinum 3200mhz 2x8gb CMD16GX4M2B3200C16 EVGA 750g2 supernova H150i pro rgb Hello everyone, Can anybody help me...I am trying understand why I am getting error codes at default 2133mhz speed 25,4f, 16, 27,4c,32,50, 37 (not in order) all codes don't shown for long apart from DRAM orange led code 32 which happens twice. I RMA'D cpu, motherboard & dram already but still having the same thing...currently on latest BIOS 1301 If i enable XMP i get the codes when I power on it switches off after 1 sec then comes back on itself When this happens i see the VCCIO voltage AT 1.3+ volts and VCCIA only raised to 1.18 lowering these helps can stop the double posts. BOTH Motherboards, RAM set and cpu !( I must make clear) do the same to voltages. So i know it is related to the RAM so I am wondering... Are these voltage strange....Since I know most people's voltage would say they should be within .05 of each other. OFC i have done all tests i can think of outside of the case with minimal hardware. I mean really though i have the 3 components here twice! Same voltages, same codes, same issues. In OS environment it seems fine and i don't see memtest errors. But I haven't gone longer than 8 hrs each time in test.