Zimmy75

I went with the 115i Pro, it's ordered now I just have to wait for it to get here. I'll purchase two more RGB fans at a later date. Thank you everyone again for all of the tips and pointers, it is much appreciated. I will keep them all in mind when I install the new hardware. Happy New Year!

Noted, thank you for the prompt response. While I would take advantage of the warranty I'm due for an upgrade. Only products from Corsair of course!

Case: Corsair Graphite Series 780T 1) Ambient temp 70 degrees 2) 2 front fans intake, rear is exhaust 3) Radiator is configured as an exhaust located on the top of the case EDITED: from intake 4) yes 5) see image below

So you think if I just make a new profile it might fix my heating issues? I am attempting to make a new profile and I don't see anywhere to select a sensor source.

Update: Okay, so I'm an idiot. The fans actually do adjust speeds when I change between quiet, balanced and extreme. I just tried it and watched the numbers, they move. I guess I was just confused because I was expecting all of the numbers to match and be the same RPM wise as well as be more noticeable in sound. Fans 1/2 are on the front running around 1400 RPM on extreme. Fan 3 is in the back running at 1350. Fans 4 and 5 are on top running at just shy of 1700. Is that all the faster the LL series fans run? (just answered my own question 600 - 1500 +/- 10% RPM.) Guess I need to invest in better fans. I may just replace my cooler as well since it's 3 1/2 years old. Thanks for the help.

Here are the screen Shots. EDIT: I attempted to connect the fans back to the radiator controller, however coming of off there is only 1 four-pin and one three-pin connector. I need 2 four-pins. To further complicate things, from a cold start I get about 10 usable minutes out of the computer before the temps ramp up into the 60-70 degree Celcius rage and my computer starts to bog down from even just surfing the web and having Spotify running. I have tried to re-apply thermal paste twice thinking that was the issue and it has not fixed it. Has my pump died even though it's reading that it is pumping at 3000 RPM?

Thank you for the response. I have to grab a screenshot when I get home after work. If I remember correctly when I first installed the unit, I tried to attach the fans to the controller on the H100i and they wouldn't work. The only way I could get them to work was through the Commander Pro. I will also attempt to revert back to that and try again later tonight as well.

Hello All, I am seeking some help trying to solve an issue that I've had for quite some time. I have the H100i V2 cooler, the Commander Pro, the RGB hub, 4 of the RGB strips and 5 of the LL 120 MM fans. Prior to getting 2 LL fans to replace the stock fans that came with the dual radiator, I was able to control the pump and fans as well as the case fans with the commander pro with no issues. When I swapped the fans on the rad over to the LL series and connected them to Commander Pro I have not been able to control any of my fans. The 5 fans are plugged into Commander Pro, ports 1-5 in order, no open spaces between. Also connected is a USB slot connected to the RGB controller as well as 1 LED strip connection. The connection from the Commander Pro to the motherboard is on a USB hub, also connected to power via SATA. The connection from the H100i V2 goes to my other remaining USB header on the motherboard, CPU fan goes to the corresponding pin in the motherboard, The fans, as well as the LED's work and, are spinning. I am able to adjust the LED's on each fan. It doesn't seem to matter which profile I select be it quiet, balanced, extreme or custom I am not able to get the fans to change speed. I have tried various ways to correct this based off of the previous feed-back on these forums and nothing seems to work. If anyone has any insight on where I should go next it would be greatly appreciated. Thank you in advance and sorry for the wall of text.