Tex_Recoil

Yes, that is part of the panel, but not were the noise is coming from. The side of that front panel were the power button/usb ports are (bezel) the trim piece, I guess you can call it that.

Hello all, I recently built a new water-cooled PC with the 7000d Airflow case and ran into a sound problem. After getting the system all built and leak tested and running for the first time. I had a intermittent rattle like sound, making me think I had a fan going out. I check all fans one at a time. None of the fans made the noise, so I put everything back together. Running like normal and waited for the noise to happen again. It turns out that the Bezel on my 7000d airflow is what is making the intermittent noise sound. Checking the bezel, it's not loose. I can't figure out why it would be making the noise and why it intermittent and not constant (which I'm glad it's not). Right now, I'm trying to figure out how to stop it from making noise. Using a small wedge of paper to move around the bezel joint and case area. But so far, I had no luck in stopping the noise. Anyone have or had this problem before? Should just live with it (hope not) or try sealing the mated surface, with something like expanding foam? As I said above the bezel is not loose, held on tight by whatever corsair used. Any advice killing this gremlin would be great.

Thank for the information, I will try and find that ek-loop leak tester for the next pc build I do. But like I said I did the old way with liquids and papertowels and the system isnt leaking. Just hate that corsair is selling a product that is cheap.

Hello all, I did forum and google search looking for Good and Bad Review on the XT Leak Tester and Instructions that were better than what came with the device. I had No luck, finding any such Information and so Im here posting. Plus no place to give a bad review or feed back. I bought my, XT Leak Tester straight from Corsair.com site . Before anyone gets mad about this post, Im a corsair product user of over of 15+ years and I'm a decent mechanic with set's of gauges to pressure test compression on vehicle motors, sets of gauges to recharge vehicle ac units as well. So when I got this tiny little tester (Xt Leak Tester) I was very disappointed that it didnt seem to be no better than a cheap tire pump for RC Cars. I dont know if it was just the product I recieved but my tester came loose, gauge head was loose. The coupler for the hose attachment unscrewed (dont know if thats ment to be that way or not.) Anyways after reading the few lines of instructions and realizing that those insturction lacked any real knowledge or help. I decide to try and get this thing working, with out going into everything I did. I gave up on the POS and went back to leak testing the old way with liquid and paper towels. I couldnt get the tester to hold any pressure at all even with using teflon tape on connection area. I dont know if Corsair does any product/ customer hands on review of items that they put the company name on. The XT Leak Tester needs to be fixed. My Two Cents. Hope Someone reads this and fix it.

LinkUp Pcie 4.0 15cm(150mm) is the right lenght for the two inner mounting spots closest to the motherboard. The mounting spot closest to glass has to be 200ish mm in length, sorry could give actual length. Didnt buy that length of riser cable. Anyway with the 15cm length riser cable, there is no need to bunch/fold the riser cable behind the Graphic card. I hope this help someone out there with the same question.

No reply and no update, guess I will tell my own findings. I've been busy doing things and had to put my new system on the back burner, anyway got back to being able to work on it and during that time. I order the LinkUp Pcie 4.0 right angle 30cm (300mm) riser cable going by the lenght of corsair riser cable. Which I will tell you is way to long, You shouldnt have to bunch the cable up that dam much. After doing a Prebuild on part of the new system. I have determined that 30cm(300mm) is way to long, for any of the 3 mounting spots in a 7000d case. Mounting spot closest to Mb(motherboard) should be 15cm(150mm) length as well as the middle mounting spot(prolly can go 20cm or 200mm lenght for middle). 3rd mounting spot (closest to side glass) should be about 20cm(200mm) lenght. So 30cm(300mm) is over 10cm(100mm) to dam long. Anyways, I have ordered the Linkup pcie 4.0 right angle 15cm(150mm) riser cable. Once it come's in, I will do a fitting check on it and make sure it fits without having to bunch the riser cable up behind the GPU. By the way, Im mounting my evga 3070 ti in the middle verticle mounting spot.

Thanks for the reply and information.

Hello all, Trying to find out if you can use non RGB Fans with H150i elite capellix AIO. A friend of mine has decide to go costume water cooling after using h150i for a year. There nothing wrong with it, he going to use the rgb fans that came with it in his new build (since all 10 rgb fans match). I have 7 Ml 120mm standard non rgb fans sitting here and want to put the AIO in a blacked out build of spare parts using those fans. I'm thinking it will work, but not sure about Icue software having a problem with non rgb fans on the AIO. Do I even need Icue? There not going to be any rgb at all in the spare part build. Will the Aio work without Icue? Thank for any replies to my questions.

Hi, did you find out the answer? I'm looking for almost the same answer, I know the corsair riser cable 30cm=300mm. I'm wanting a shorter riser cable PCie 4 were I don't have to fold it up behind the card and might block airflow to it or from it. Plus wanting the cable to fit the case holes it has. If you have figured this out, mind sharing the answer? Thanks

Hello, did you find answer to this. I came here to find the answer to the same question you are asking. I want a PCie 4 riser cable for my new system build in a corsair 7000d airflow using the case vertical mount holes. If you have the answer please tell. Thanks

Got it fixed, downgraded to Icue version 3. Everything started working again. Dont know why, with version 3 all rgb lighting was working again. Knowing that version 3 worked fine. I decide to uninstall it and try version 4 of Icue again. With I fresh install, not doing the in program update. Found out why version was effecting my lighting. It seem that something is wrong with how the program is saving Lighting Effects and Hardware Lighting. Its a hit or miss reproducing the problem. Sometimes it will save the info for both on the fly and then after a reboot those setting are gone. If I only mess with one, on one device. Say memory Lighting Effects and not Hardware Lighting and set it for all device's. Icue works, save the info and works fine. Tested by doing Multiple reboots of the system. Dont know why it doing it that way. Im just glad it fixed.

Well the problem has grown, now when I startup my system the Dominator Memory are all Blacked out. Half of my Ql120 rgb fans are blacked out too. Once I let the system set for a few seconds after Boot and desktop is showing. It corrects itself turning the memory and fan lighting back on. Going from having one problem to having this new one and the only thing I changed was from Icue version 3 to 4. To answer your question about my system, Motherboard is Evga and gpu as well. Mb is z490 and gpu 2070, I do not have any of the software for either Mb or Gpu installed on my system to change lighting. I did have the software install about year ago when I first built my system just to set the lighting. Then I uninstalled it. Like I said everything was has been working fine Up until I install Icue version 4. I had been running Icue version 3 for a year with no problems. Im incline to think it Icue version 4 is the problem, since it the only software update I did, when I started getting this lighting problem. But to let you know I did do a clean Install of Icue verion 4, deleted Wallpaperengine software, And since I dont have MB or Gpu manufactor software install to control Rgb, was nothing else to delete. Since the Fresh Install of Icue version 4.14.179 now I have the problem with startup of my system missing lighting on memory and half my fans. Im downgrading back to Version 3. Will let you know if it corrects my problems.

Hello all, I upgraded Icue to V.4.14.179 just 2 days ago. Right away started having problems with memory lighting. Icue seems to turn the lighting option off on one or all memory. Its totally random what it does, I have 4 dimms of Dominator Rgb installed. It will shut down a random stick of memory or all of them together. I check the Icue software and the memory is still set to display what I have had selected. If I uncheck and recheck the option. Boom! problem is fixed until the next reboot and then it start all over. I have WallpaperEngine installed, on my system. But when I started to have this lighting problem with the memory, I disabled it. It doesnt matter if wallpaperengine is running or not. The problem still exist. Anyone having the same problem? Thinking on downgrading back to Version 3 icue which didnt have this problem.

Hello all, I have a H150i Elite Capellix 360 Aio cooler. I have been noticing big temperature difference between the Aio water temps and the Cpu. The Aio will say the liquid tempts at 35c and and Cpu will be at 35c not under load. But when Cpu is under load and running at 65c or higher. The Aio will still say it at 35c, even after a hour. Is this Right? Shouldnt the temp come up on the Aio? It has me worried that either the paste on the Aio isnt as good as it should be or that the waterblock not seated right. I have check everything and made sure the mount screws are tight. The system is only a few months old, didnt notice the temperature difference between Aio and cpu until now. Dont remember ever having seen it before now. Should I re-paste the water block? (paste currently on it is from factory) and reseat the block? Thanks for any suggestion.

**Update** Got the replacement Kit in 4 days earlier than the shipper status page said. They are working great with all color working and matching. Couldn't be happier on the quick turn around and gettig my problem solved!

Well just found out about this rgb lighting problem with Dominator memory, the hard way. After I built my new system, 2 of the 4 Dominator Platinum Rgb Memory sticks is having rgb lighting problems. One memory stick has two malfunctioning Led lights and the other has only one malfunction led light. Memory Kit I got from Newegg almost 3 months ago and just finally had everything ready for my new system (Hate Covid for slowing down my build). The memory Kit is the CMT32GX4M4C3200C16, made in Taiwan. Going to see if I can Rma them. Just hoping they will only need the two malfunction memory sticks not the whole kit. So I can still run my system on the two good sticks. P.s. Tried everything I read here, force update (no luck) and so on. *Update* Rma went through, so sending the Dominator out this friday. All the way back to Taiwan, hoping for a quick turn around. Friend loaned me some old non rgb dominator memory to keep my new system running.

Thanks, if you wouldn't mind Have another question. Got it all wired up and working but having one problem can't seem to find the answer too. When booting up or shutting down fans on the Lighting Node Core go white. Everything on the Commander Core stays colored shutting down or booting up. Is something wrong with the lighting node core? or is it just that way?

Hello all, I have seen a few post showing image's of H150i Elite Capellix and 9 or more fan's being wired. The problem I'm pretty sure, I know the answer too. Just want to make sure, I'm right. The image's all show using a RGB Led Fan Hub, which I don't have. Instead I have Lighting Node Core (3 of them), I'm sure I can use the Core to replace Hub in the image and wire my system up and have it work? My setup is as follow's: H150i Elite Capellix w/ commander core Commander Pro 10 x Ql 120 fans and 3x lighting node core (only using 1 of them) I will have the Commander Pro hooked to 1 motherboard usb connector, other MB usb connector for front case panel. The Commander Core and Lighting Nobe Core hooked to the Pro's Usb connector's. I'm pretty sure this will work? Just wanting to make sure before I have wiring nest made. Any help or advise you can give me will be great.

Hello all, been a few years since I Upgraded or even messed with my system. So I Jumped right in, bought a Commander Pro and Update all my fans to Ql's which came with the Light Node Core. Question I have is testing to make sure everything hooked up right and working, on my new PC build. I haven't yet received my Z490 dark MB yet as it back ordered. I'm wanting to test out the fans and RGB without the Commander Pro hooked up to a MB usb port. Is it possible without damaging anything? or do I need to wait on the Mb to hook it all up to a usb port? Any help you can give me, would be great. Also hope this is the right forum to post this in. Thanks.