will_s

Have flow from Res (XD5) to Rad to GPU and from GPU to CPU ( XC7 I think )to Rad and back to res Res ( 2 rads ) But I cant recall if for the CPU water block they have to go in a particular order ...so if the logo facing down does the input go to the right or left hole?

well I am worried because I have this in my system on a 2080ti and I hate the idea of water leaking into my PC ........ so can I remove it and get a RA from Corsair"?

Try using an extension USB cable and having the dongle far away for the actual PC ... worked for me

ok, an update Since I moved my other wireless devices and used an USB extension cable and have the transmitter on my left side I have not had any static or dropout problems So I have my PC on the floor next to my Obutto Gaming Rig......it has the 2 dongles at the front of the Case and the mouse and keybpard are on a moveable platform/table and the Virtusso has a USB extension (actually it was the one that came with my keyboard (logitech G915 and Pro Mouse ) and that dongle is not on the left hand side.... and no static or dopouts

https://www.intel.com/content/www/us/en/products/docs/io/universal-serial-bus/usb3-frequency-interference-paper.html I have an extension for my wireless on my keyboard but I dont use it but will now put the wireless dongle for my headphones on this

ok, its not perfect had a slight bit of static and what appeared to be a few very quick cutouts........ you can just notice but not like the 3 to 4 second cutout before

ok, I see an updated iCue has come out and I have updated and the sound is not cutting out after 2 sessions of driving in iRacing

ok, I have tried it after turning both the wireless mouse and wireless keyboard off and it works flawlessly but I need the mouse and keyboard. Now the previous wireless headset was the arctic 7 and it never had a problem but the mic is bad. I never saw any warnings about using this with other wireless devices causing problems

Ok, brought these because of the good reviews for the Mic and it does a good job. But I have a bad problem in iRacing with the sound cutting out. It is working and for 1 to 3 seconds the sound can just go out and then come back on. Now I have the dongle at the back of my PC and moved it to the front and no difference. I updated iCue (have Commander Pro ) to the latest as well as firmware. Now I have a wireless mouse and keyboard ( gskill ). Is this a common problem ? For a gaming headset this is a terrible problem and will return it for a refund if I cant get this fixed. Any clues ?

Putting a loop in other PC and only hrydro x part will be the GPU block because I prefer them Will be using just the Hydro GPU and was wondering how to connect it to the Commander pro? The Pro will only be used as a fan hub ( no RGB on fans ) and basically only RGB will be EK CPU and Distro Block as well as hydro x GPU I would assume you would need some sort of extension cable. I am not up to scratch on RGB at all

because its set to fan and not pump so it acts like a fan ????

but the primary difference is the XC7 is designed for LGA 115x/AM4 sockets, and the XC9 is for LGA 2011/2066/TR4

thanks but looks like due to redesign of the top part of the Dynamic 011 XL the thicker rad wont fit and with rise card wont fit in the bottom either

WELL THE Corsair RGB Fan LED Hub is connected to one of the LED channels on the Comander pro but that only handles 6 and you would need another RGB fan LED hub for the other 6 which looks like you have BUT then you wouldnt have GPU/CPU/Pump connection. You can add another Commander Pro and connect them together with USB 2 but in the end you end up with lots of cables But to just get one working...plug the rgb into the RGB fan led hub and connect that to one of the LED channels on the CP. Now they wont light up until you actually add them in the iQue software using drop down boxes.. Once you do that you should be able to do the cpu/gpu/pump but that leaves 5 fans without RGB so most probeley you will need another CP You just have to add them in and then play around and remember you have to connect the CP to your motherboard via USB2

Going to change my case and my loop. Going to add a EK-Quantum Kinetic FLT 360 D5 PWM D-RGB - Plexi pump resovoir with the XR5 and XR7 rad on bottom and top of case. Basically removing the XD5 RGB Reservoir/Pump Combo and was wondering would the temp gauge for that work in the FLT 360? Would the pump on the FLT360 be able to coonect to the power Commander and work just the same in the software ie. control speed. I would use Manual settings for pump speed as I hate the Pump and Fan control speeds tha iCue sets btw:the pump details are and the one is red is the important one Pump electrical and mechanical properties: - Motor: Electronically commuted spherical motor - Rated voltage: 12V DC - Power consumption: 23W - Maximum pressure head: 3.9m - Maximum flow: 1500L/h - Maximum system temperature: 60°C - Materials: Stainless steel, PPS-GF40, EPDM O-rings, Aluminium oxide, hard coal - Power connector: 4-Pin Molex- and 4-Pin PWM FAN connector

Zotac are as helful as a boil on the butt...when I asked them about the 2080ti they said ask the water block maker anyway..learnt my lesson.....never again will I purchase a Zotac product

letting the pump run dry not have all the stops on not having paper towels not using the bridge for fulling the system hey...just did my one and was as nervous as hell

nah, doesnt work...tried the lot so I guess I will RA it back............nah, just put it in the ignore basket and set the other 2 fans to same speed using custom mode edit: I didnt tuen off the psu but did so when changing some plugs over and adding another SSD and on restart they are all working

Was wondering the same about pump speeds and have been running it 100% to get out air and I thought something was wrong....but it works and I see a lot of little bubbles in the GPU block :-) To be honest I am very surprised that I cant hear the pump after reading comments about pump whine With coolant at 31C the pump runs about 2100rpm (48%) ..this is idle with a room temp of 26C

One of my RD120 fans has lost control...have 3x120mm RD120mm fans on top plugged into fans slots 1,2 & 3 and the fan1 is just stuck at 1566 rpm no matter what I do..put it to zero or put it to 100% and its stays at 1566rpm..RGB works on all The other 3 RD120mm fans in the rear 30mm rad work good and I plugged the Noctua into the CPU fan header. Still may find another splitter and do a splitter on each rad with the other one solo like c-attack suggested I guess its take the case apart and swap connections or just ignore it

was more worried about mixing fans so I swapped 2x RD120's fans out of another PC and put them in...and the temps went down

Using splitter cables how many fans can the Commander pro Handle? I have 3 HD120 fans and 3 Noctua 120mm NF-S12A connected to 2 radiators and another HD120mm fan at the bottom of the case as well as the XD5 RGB Pump connected to slot 6 on the Commander Pro. So I need 2 splitter cables ...one to connect the bottom HD120 fan to one of the other HD120 fans by splitter cable and connect the Noctua fans with one splitter cable and the other by itself. Will run the Noctua fans on Custom Curve as they are 1200rpm and the HD120's about 1400rpm....about 70% on another Custom curve. So how many fans can it support? ( including the XD5 ) And can you mix your fans ? ( like the Noctua above )

thanks for that and a big thanks to all who have replied to my questions...I couldn't have completed the task with the help of people like c-attack among many Temp of the PC is higher then I expected but its a warm day .........still its like having a fish tank......very soothing to look at :-)

Ok, iCue can see my hydro X components as shows in the pic but no RGB shows on the components The RGB on thew HD fans show and work and I can change RGB ( they are on Channel 2 ) edit: no idea why but after switching channels they are now working ...I just plugged the pump RGB on channel 2 and that worked, so powered off and put the GPU and CPU in and powered back on and went to icue and enabled them and they work...very strange but have to say the hydro=x RGB effects on GPU and CPU look great

ok, dont like having zero speed on my fans when using hydro fan mode at the top as part of their job is to remove "hot" air from the case....so would putting these fans to quiet mode upset the balance?