Jump to content

will_s

Members
  • Posts

    157
  • Joined

Posts posted by will_s

  1. ok, an update

     

    Since I moved my other wireless devices and used an USB extension cable and have the transmitter on my left side I have not had any static or dropout problems

     

    So I have my PC on the floor next to my Obutto Gaming Rig......it has the 2 dongles at the front of the Case and the mouse and keybpard are on a moveable platform/table and the Virtusso has a USB extension (actually it was the one that came with my keyboard (logitech G915 and Pro Mouse ) and that dongle is not on the left hand side....

     

    and no static or dopouts

  2. ok, I have tried it after turning both the wireless mouse and wireless keyboard off and it works flawlessly but I need the mouse and keyboard.

     

    Now the previous wireless headset was the arctic 7 and it never had a problem but the mic is bad.

     

    I never saw any warnings about using this with other wireless devices causing problems

  3. Ok, brought these because of the good reviews for the Mic and it does a good job. But I have a bad problem in iRacing with the sound cutting out. It is working and for 1 to 3 seconds the sound can just go out and then come back on.

     

    Now I have the dongle at the back of my PC and moved it to the front and no difference. I updated iCue (have Commander Pro ) to the latest as well as firmware.

     

    Now I have a wireless mouse and keyboard ( gskill ).

     

    Is this a common problem ? For a gaming headset this is a terrible problem and will return it for a refund if I cant get this fixed.

     

    Any clues ?

  4. Putting a loop in other PC and only hrydro x part will be the GPU block because I prefer them

     

    Will be using just the Hydro GPU and was wondering how to connect it to the Commander pro? The Pro will only be used as a fan hub ( no RGB on fans ) and basically only RGB will be EK CPU and Distro Block as well as hydro x GPU

     

    I would assume you would need some sort of extension cable. I am not up to scratch on RGB at all

  5. WELL THE Corsair RGB Fan LED Hub is connected to one of the LED channels on the Comander pro but that only handles 6 and you would need another RGB fan LED hub for the other 6 which looks like you have BUT then you wouldnt have GPU/CPU/Pump connection.

     

    You can add another Commander Pro and connect them together with USB 2 but in the end you end up with lots of cables

     

    But to just get one working...plug the rgb into the RGB fan led hub and connect that to one of the LED channels on the CP. Now they wont light up until you actually add them in the iQue software using drop down boxes.. Once you do that you should be able to do the cpu/gpu/pump but that leaves 5 fans without RGB so most probeley you will need another CP

     

    cp.png

     

    You just have to add them in and then play around

     

     

    and remember you have to connect the CP to your motherboard via USB2

  6. Going to change my case and my loop. Going to add a EK-Quantum Kinetic FLT 360 D5 PWM D-RGB - Plexi pump resovoir with the XR5 and XR7 rad on bottom and top of case. Basically removing the XD5 RGB Reservoir/Pump Combo and was wondering would the temp gauge for that work in the FLT 360?

     

    Would the pump on the FLT360 be able to coonect to the power Commander and work just the same in the software ie. control speed. I would use Manual settings for pump speed as I hate the Pump and Fan control speeds tha iCue sets

     

    btw:the pump details are and the one is red is the important one

     

    Pump electrical and mechanical properties:

    - Motor: Electronically commuted spherical motor

    - Rated voltage: 12V DC

    - Power consumption: 23W

    - Maximum pressure head: 3.9m

    - Maximum flow: 1500L/h

    - Maximum system temperature: 60°C

    - Materials: Stainless steel, PPS-GF40, EPDM O-rings, Aluminium oxide, hard coal

    - Power connector: 4-Pin Molex- and 4-Pin PWM FAN connector

  7. nah, doesnt work...tried the lot

     

    so I guess I will RA it back............nah, just put it in the ignore basket and set the other 2 fans to same speed using custom mode

     

    edit: I didnt tuen off the psu but did so when changing some plugs over and adding another SSD and on restart they are all working

  8. Was wondering the same about pump speeds and have been running it 100% to get out air and I thought something was wrong....but it works and I see a lot of little bubbles in the GPU block :-) To be honest I am very surprised that I cant hear the pump after reading comments about pump whine

     

    With coolant at 31C the pump runs about 2100rpm (48%) ..this is idle with a room temp of 26C

  9. One of my RD120 fans has lost control...have 3x120mm RD120mm fans on top plugged into fans slots 1,2 & 3 and the fan1 is just stuck at 1566 rpm no matter what I do..put it to zero or put it to 100% and its stays at 1566rpm..RGB works on all

     

    The other 3 RD120mm fans in the rear 30mm rad work good and I plugged the Noctua into the CPU fan header. Still may find another splitter and do a splitter on each rad with the other one solo like c-attack suggested

     

     

     

    I guess its take the case apart and swap connections or just ignore it

  10. Using splitter cables how many fans can the Commander pro Handle? I have 3 HD120 fans and 3 Noctua 120mm NF-S12A connected to 2 radiators and another HD120mm fan at the bottom of the case as well as the XD5 RGB Pump connected to slot 6 on the Commander Pro.

     

    So I need 2 splitter cables ...one to connect the bottom HD120 fan to one of the other HD120 fans by splitter cable and connect the Noctua fans with one splitter cable and the other by itself.

     

    Will run the Noctua fans on Custom Curve as they are 1200rpm and the HD120's about 1400rpm....about 70% on another Custom curve.

     

    So how many fans can it support? ( including the XD5 )

    And can you mix your fans ? ( like the Noctua above )

  11. thanks for that and a big thanks to all who have replied to my questions...I couldn't have completed the task with the help of people like c-attack among many

     

     

    Temp of the PC is higher then I expected but its a warm day .........still its like having a fish tank......very soothing to look at :-)

  12. Ok, iCue can see my hydro X components as shows in the pic but no RGB shows on the components

     

    rgb.png

     

    The RGB on thew HD fans show and work and I can change RGB ( they are on Channel 2 )

     

     

    edit: no idea why but after switching channels they are now working ...I just plugged the pump RGB on channel 2 and that worked, so powered off and put the GPU and CPU in and powered back on and went to icue and enabled them and they work...very strange but have to say the hydro=x RGB effects on GPU and CPU look great

×
×
  • Create New...