Jump to content

axiun

Members
  • Posts

    51
  • Joined

  • Days Won

    3

Everything posted by axiun

  1. That turned out to be it. I was using a contact frame replacement for z690. I've reseated my AIO and reseated the contact frame multiple times, but none of it would work. Once I switched back to the stock intel ILM mechanism, the system has been waking from sleep without rebooting and I haven't seen a detect memory error in a day. Fingers crossed, that's all it was. Bummer, as the temps on this CPU are 5-6c higher without the contact frame, but I couldn't get the pressure just right. This is with the thermalright frame.
  2. Thanks! No dice, unfortunately. I did a complete cmos reset. Chose to enforce all limits, did not set xmp and manually chose my kits rated 5200mt speed and set the primary rated timings - 40-40-40-77. Put the system to sleep and tried to wake it up, the system hung on 'detect memory' 😞
  3. I thought somethings up with the site because the OP link was acting weird. I realized that it's an incomplete url. So that makes sense.
  4. Err, there's no way to edit posts after a certain amount of time? Thats... odd. Seems corsair changed the product link. Here's the new link to the kit I'm using. https://www.corsair.com/us/en/Categories/Products/Memory/DOMINATOR-PLATINUM-RGB-DDR5-Memory---White/p/CMT64GX5M2B5200C40W
  5. I think something’s up with the site. Forums are loading funky and the main site is acting strange. Yeah, the whole point of switching to this 2x32 kit was that 4x16 was very unstable
  6. It’s a 2 stick kit. 2x32gb. It’s liked in the original post. I’ve reset cmos multiple times.
  7. I've had this board since launch. In the begging, I had it with 4x16GB sticks from two corsair kits and with early bios revisions that was a nightmare. Fine, I've sold the kits and switched to a single 64GB kit. I was hoping for plug and play. Just XMP is enabled. https://www.corsair.com/us/en/Catego...GX5M2B5200C40W I need stability out of this rig, and I'm having two big issues. Every couple of reboots, I'll get stuck on memory detect while booting. I'll have to power cycle and it'll kick me to bios saying it couldn't boot, I'll go into bios and without changing anything, it'll keep working for another couple of boots. The other issue is win 11 refuses to wake from sleep. Instead of waking the system, it will reboot. Bios is 2004 Memtest passes fine. Tried VCCSA voltages from 1.1-1.4, no affect. Tried setting the speed to 4800mhz, no affect. Updated bios from 2004 to 2103, no affect. Tried slots A1-B1, system wouldn't even post at anything above 4000mhz. What is the issue with this kit? Why doesn't it work at XMP rated settings? Current bios settings -
  8. I'm referring to something else. The plugin corsair release a few years ago that hasn't been updated in ages. https://help.corsair.com/hc/en-us/articles/360035656371-How-to-Integrate-Armoury-Crate-with-iCUE
  9. It's 4 months since the launch of alder lake and corsair dominator ddr5 modules. The last update for the plug in is from 2019.
  10. It's been out for a year and got very, very little love. Typically, this would be the time to launch the next version of the product.
  11. Thanks for sharing! If at all possible, can you take a picture with the acrylic window removed? It's a bit tough to tell if the rails that the window slides into are part of the brace or if they're permanently attached to the psu shroud.
  12. So, it's been about 8 months since this thread started. I'd like to ask again. Is the nexus dead? Is there going to be an updated version of the nexus if or when this software update ever comes out? I realize software is hard, but we could really use some smaller incremental updates once in a while.
  13. Anyone using an H150 to cool their 5950x, what are your idle temps like? The mount is absolutely atrocious on this cooler and it's sometimes tough to keep the pump flat on the chip while mounting. On this one that I've received, while finger tightening the mount bolts, the clamp mechanism will slide out a bit out of the pump base. In any case, my ambient room temps are usually around 25c. Water temp is around 37-39 at idle. CPU idles 55-60c with ~5% load. Gaming is usually around 75c or so. Not really blowing me away considering this is a 360 rad.
  14. Dominator Platinum Cappelix sticks are not adhering to lighting profiles created in icue 4. Switching profiles in the new icue will change the pre-defined lighting on all components except the ram sticks. Edit - None issue. I didn't see that the the ram sticks were set to hardware lighting. Changing to lighting effects instead of hardware, profiles work as intended.
  15. I swear I saw this function at some point, but digging around through icue now, I can't seem to find it. Is there a feature to automatically cycle through the screens of widgets? For instance screen 1 is 6 fan speed widgets and screen 2 is 6 temp widgets.
  16. I've found a strange bug. After some time, the screen will pause all monitoring and just freeze frame. After tapping the screen, it will fast forward like a 10x video to catch up to the current frame and resume monitoring. iCue - 3.37.140 Nexus Firmware - 2.2.6 Has anyone experienced this as well?
  17. Similar issue here. x570 Prime on my end. Have an Asus gpu in the rig that I'm able to control with iCue, but I can't control the motherboard. It shows up in iCue and I can select the color profiles, they just don't seem to affect the board. EDIT - I've fixed the issue by replacing the asus plugin included with icue with the older 'beta' version available on these forums.
  18. Just installed a new h115i in my system. Trying to power the system on causes either an ocp or a short. I've double checked that all cables are fine. The PSU is an SFX750 and only the stock cables are used. Disconnecting the Commander Core from SATA power fixes the issue and the system boots fine. I don't have anything else connected to SATA on this system. I've tried all of the available SATA/Periph ports available on the PSU and I've tried all of the available cables that came with the PSU. I've tried the SATA connections before with a Commander Pro and they worked fine. Has anyone ran into this? Is this a faulty unit? EDIT - SOLVED - It was a noctua fan extension causing a short.
×
×
  • Create New...