yhs85 Posted March 22, 2013 Share Posted March 22, 2013 Hi, I'm new to Watercooling so please bare with me. I am planning to get a 360mm rad for up top exhausting on push config. A 140mm rad at the bottom near PSU, Replacing case fan intaking and a 120mm rad on the rear, intake again. The rear 120mm rad will be a stealth as to allow room for the bigger 360 SR1 56mm up top. Will these all fit ok? Will there be enough airflow do you think? I'm going with the dual d5 res/pump, i hope this will be sufficient. Thanks for the help :biggrin: any tips welcome! Link to comment Share on other sites More sharing options...
yhs85 Posted March 23, 2013 Author Share Posted March 23, 2013 http://i1006.photobucket.com/albums/af181/sxdrgsvlnce/Android%20Forums%20stuff/BUMP.jpg Link to comment Share on other sites More sharing options...
yhs85 Posted March 23, 2013 Author Share Posted March 23, 2013 Is it physically possible to fit the 360, 140 and 120mm RADS in there? The 120mm on the rear with be a thin stealth rad. Link to comment Share on other sites More sharing options...
yhs85 Posted March 24, 2013 Author Share Posted March 24, 2013 Thanks for the replies :[pouts: Link to comment Share on other sites More sharing options...
alan1476 Posted March 24, 2013 Share Posted March 24, 2013 Hi, I'm new to Watercooling so please bare with me. I am planning to get a 360mm rad for up top exhausting on push config. A 140mm rad at the bottom near PSU, Replacing case fan intaking and a 120mm rad on the rear, intake again. The rear 120mm rad will be a stealth as to allow room for the bigger 360 SR1 56mm up top. Will these all fit ok? Will there be enough airflow do you think? I'm going with the dual d5 res/pump, i hope this will be sufficient. Thanks for the help :biggrin: any tips welcome! Get the new Corsair 100i enclosed loop, its good enough for anything you throw at it. Link to comment Share on other sites More sharing options...
yhs85 Posted March 24, 2013 Author Share Posted March 24, 2013 I have the H100i and quite frankly, It's shocking. It's loud as hell even on lowest RPM. And I'm sure it wont cool my SLI 670's will it? :) Link to comment Share on other sites More sharing options...
Administrators Technobeard Posted March 24, 2013 Administrators Share Posted March 24, 2013 If it's loud, open a ticket and we'll replace it. I'm not sure if they'll fit in an 800D (I'm not a W/C guy), but the 900D will be able to take a ton of rads from what George has said in the video: http://www.corsair.com/900d Haven't seen that bump pic before lol. The internet never fails to amuse :) Link to comment Share on other sites More sharing options...
mirkoj Posted March 24, 2013 Share Posted March 24, 2013 or get 2 noctua nf-f12 for h100i and discover new meaning of silence and performance :) they are truly great Link to comment Share on other sites More sharing options...
Mr_Armageddon Posted April 7, 2013 Share Posted April 7, 2013 Hi, I'm new to Watercooling so please bare with me. I am planning to get a 360mm rad for up top exhausting on push config. A 140mm rad at the bottom near PSU, Replacing case fan intaking and a 120mm rad on the rear, intake again. The rear 120mm rad will be a stealth as to allow room for the bigger 360 SR1 56mm up top. Will these all fit ok? Will there be enough airflow do you think? I'm going with the dual d5 res/pump, i hope this will be sufficient. Thanks for the help :biggrin: any tips welcome! Those rads should all fit, as long as you remove the boom HDD cage. Airflow may be a tad less than optimal with that configuration being that you basically have 4 exhaust fans and only 1 intake. Its a limitaion with the 800D that can easily be fixed with the bottom rad mod that I did. The mod is a sticky under the Cases section of the forum. http://forum.corsair.com/v3/showthread.php?t=81698 Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.