andreaz70 Posted March 12, 2013 Share Posted March 12, 2013 Seem to work great. LED is set to black at all 3 Temps, you may need to configure this. Everything working here on the first look. Ramguy, you might get something pass to the developers? With my SSD (a Samsung Pro 840) i get the temp out of smart as difference from 100 deg. So in Link2 it show up 74 deg. The truth would be 100-74. Maybe they can introduce this in a future release? Dunno if your SSDs do the same, but i guess they will... Thanks for the great work. I got not any problem with installing it... Regards, Andreas Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted March 13, 2013 Corsair Employees Share Posted March 13, 2013 That is not usually caused by the drives firmware. IE with many of our SSD's we have health monitoring disabled so you may get an abnormal temp reading. But I will report it to our software team. Link to comment Share on other sites More sharing options...
andreaz70 Posted March 13, 2013 Author Share Posted March 13, 2013 The temp is true, as long you consider is something like tjmax on processors. I think they do a similar reading on SSDs. If i do 100- the reported 74 deg i get to 26 deg C, what seems to be very true. Even Link2 say "Samsung Drive Difference from 100" as Modelname. CrystalDisk go to the same temp (26 deg) and i believe even the samsung software report this. Maybe they dont report the temp of the board itself, more the temp of the controllerprocessor, so considering it is kinda distance to anything like tjmax wont be wrong.. :) Thanky! :) Andreas Link to comment Share on other sites More sharing options...
tim_hamblin Posted March 14, 2013 Share Posted March 14, 2013 I had a similar issue with y Crucial M4 SSD. However, after installing the new Corsair Link Software Update Version 2.3.4816 - the SSD drive is no longer visible (my standard Seagate HDD is still there with the temperature being displayed)... Link to comment Share on other sites More sharing options...
Stoke192 Posted March 14, 2013 Share Posted March 14, 2013 Well, i have also a similar issue with the new version of the Link software. It shows my Scandisk SSD at 128 degrees on the system page but it's not showing my other two sata hdd's, yet they're listed on the devices page. Any idea's ? Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted March 19, 2013 Corsair Employees Share Posted March 19, 2013 I haven't received an update from our SW team regarding this issue where drive temp or drive themselves not showing in Link SW. I will do a follow up on this. Thanks for the feed backs. Link to comment Share on other sites More sharing options...
Yellowbeard Posted March 19, 2013 Share Posted March 19, 2013 Well, i have also a similar issue with the new version of the Link software. It shows my Scandisk SSD at 128 degrees on the system page but it's not showing my other two sata hdd's, yet they're listed on the devices page. Any idea's ? Most likely your SSD does not even have a temp sensor. In addition to that, when SSDs do not have temp sensors, they do still report a SMART value for that sensor. So, in your situation, the SSD vendor needs to have a static value reported for temps so that it does not confuse SMART monitoring. Link to comment Share on other sites More sharing options...
secuver Posted November 13, 2013 Share Posted November 13, 2013 I have a new corsair ssd FORCELS sata3 of 60Gb installed in my computer. when i look up the temp he gives a value of 99°. when i instal my camera software (mirasys) the watchdog of this software shuts down my computer after 30sec because the temp of the hard drive is to high. The value of 99° is not right i think, is their a fix or a wordaround to solve this problem? thanks Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.