L3p Posted December 23, 2012 Share Posted December 23, 2012 http://www.l3p.nl/files/Hardware/L3p%20AlCu/l3p_alcu.png Here a small project :) The TC-100 is already an out of production case and was a present from Marco en Ruud van Cooler Master Benelux. Always wanted to do something with passive cooling! http://www.l3p.nl/files/Hardware/L3p%20AlCu/1-start/2%20%5B550xl3p%5D.JPG Cause it was a really busy year for me I wasn't able to find the time for it. Finally found it! For the support I got from several company's I though, why not make is a small project :) http://www.l3p.nl/files/Hardware/L3p%20AlCu/1-start/3%20%5B550xl3p%5D.JPG My plan is to get this working as a passive cooled htpc/internet pc with a Corsair logo window and brushed aluminum look. http://www.l3p.nl/files/Hardware/L3p%20AlCu/1-start/4%20%5B550xl3p%5D.JPG Hardware: Cooler Master TC-100 Cooler Master Copper passive cooling kit Lian Li SD-03A Case Stand Silver AC Ryan Aluminum brushed 1mm panel Lamptron 19mm switch blue Intel Core i3 2120T Asus P8H77-I PicoPSU 150XT Corsair Dominator Platinum 8GB 1866Mhz Corsair Neutron GTX 120GB Corsair Vengeance K60 Corsair Vengeance M90 Big thanks to: http://redharbinger.com/photo/Cross/Sponsorlogo/corsair.pnghttp://redharbinger.com/photo/Cross/Sponsorlogo/cm.png http://redharbinger.com/photo/Cross/Sponsorlogo/asus.pnghttp://redharbinger.com/photo/Cross/Sponsorlogo/highflow.png Link to comment Share on other sites More sharing options...
stratosrally Posted December 23, 2012 Share Posted December 23, 2012 Looking forward to more of your magic, my friend - happy holidays! Link to comment Share on other sites More sharing options...
L3p Posted December 23, 2012 Author Share Posted December 23, 2012 Thanks stratosrally! This will be a bit smaller project though :) The hardware. http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/1%20%5B550xl3p%5D.JPG Don't know why, but I just love brushed aluminum. http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/2%20%5B550xl3p%5D.JPG Won't be much left of the original steel frame. http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/3%20%5B550xl3p%5D.JPG Will also replace the front since it won't have a dvd/blu-ray player. http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/4%20%5B550xl3p%5D.JPG Can't wait to figure out the cooling as the original kit was designed for real old VIA chipset mainboards :) http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/5%20%5B550xl3p%5D.JPG At first it was going to be an AMD setup but cause of some driver issues and heat problems I went for an intel based setup. http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/6%20%5B550xl3p%5D.JPG Also ordered a PicoPSU 150XT. http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/7%20%5B550xl3p%5D.JPG The H77 board. http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/8%20%5B550xl3p%5D.JPG And the Intel i3 2120T (35W) http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/9%20%5B550xl3p%5D.JPG So glad Corsair wanted to help out on this little project! http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/10%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/11%20%5B550xl3p%5D.JPG First run with the new psu went perfect. http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/12%20%5B550xl3p%5D.JPG Without any airflow it gets pretty hot :) http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/13%20%5B550xl3p%5D.JPG Set of aluminum Lian Li casefeet. http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/14%20%5B550xl3p%5D.JPG Outside all Alu. http://www.l3p.nl/files/Hardware/L3p%20AlCu/2-hardware/15%20%5B550xl3p%5D.JPG Next update the heatpipes. Link to comment Share on other sites More sharing options...
wwwicked Posted December 24, 2012 Share Posted December 24, 2012 Really nice project L3p. Looking forward to see more of your progress. Link to comment Share on other sites More sharing options...
L3p Posted December 27, 2012 Author Share Posted December 27, 2012 Thanks Wwwicked! So ... got everything off my attic :) http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/1%20%5B550xl3p%5D.JPG Ohh boy :P http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/2%20%5B550xl3p%5D.JPG Just love untreated copper. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/3%20%5B550xl3p%5D.JPG Ever seen a Cooler Master heatpipe bending iron? :) http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/4%20%5B550xl3p%5D.JPG Because these sets are originally for VIA chipsets it was quite a puzzle. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/5%20%5B550xl3p%5D.JPG This'll be it. Left for the CPU with 4 heatpipes, on the right, 2 pipes for the chipset. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/6%20%5B550xl3p%5D.JPG While I was at work I came up with a solution for the front with unwanted DVD slot. Just make a new one :) http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/7%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/8%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/9%20%5B550xl3p%5D.JPG Because it's about $4 a kilo I also took 2 bigger panels for if I ever want it to support ATX. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/10%20%5B550xl3p%5D.JPG Finding the right size logo for the casewindow. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/11%20%5B550xl3p%5D.JPG Further with the copper. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/12%20%5B550xl3p%5D.JPG Was looking for a way to mount it all .. luckily I had an EKWB bracket left somewhere. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/13%20%5B550xl3p%5D.JPG Will probably become something like this. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/14%20%5B550xl3p%5D.JPG First need to clean it up and shorten the bolts. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/15%20%5B550xl3p%5D.JPG Nice mess again :D http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/16%20%5B550xl3p%5D.JPG To get the EK bracket working with the copper parts I had to change some parts. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/17%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/18%20%5B550xl3p%5D.JPG Bottom with just 4x M4 and plastic rings. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/19%20%5B550xl3p%5D.JPG Top with a nut and MDPC-x cap. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/20%20%5B550xl3p%5D.JPG And measuring again. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/21%20%5B550xl3p%5D.JPG Decided to just replace the front panel only. (Not add a back one) http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/22%20%5B550xl3p%5D.JPG Getting the tools from the car. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/23%20%5B550xl3p%5D.JPG The panels are pretty damaged, will be quite some sanding. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/24%20%5B550xl3p%5D.JPG Getting the switch in the panel. http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/25%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/3-mod1/26%20%5B550xl3p%5D.JPG Link to comment Share on other sites More sharing options...
L3p Posted December 30, 2012 Author Share Posted December 30, 2012 Larger update this time! (For the ones who didn't know, all my photos are linked to bigger ones) Finally able to use the investment I did a year ago :) AC Ryan Brushed alu panels. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/1%20%5B550xl3p%5D.JPG Lets get the grinder first. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/2%20%5B550xl3p%5D.JPG Hi http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/3%20%5B550xl3p%5D.JPG I'm going to use the brushed aluminum on both sides of the original bottom/mainboard tray. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/4%20%5B550xl3p%5D.JPG Panel for the bottom, will be using acrylic on top of that. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/5%20%5B550xl3p%5D.JPG And the inside, or mainboard tray. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/6%20%5B550xl3p%5D.JPG Measuring and fitting the bottom panel. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/7%20%5B550xl3p%5D.JPG And again measuring and fitting with the mainboard. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/8%20%5B550xl3p%5D.JPG This is how the bottom will look. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/9%20%5B550xl3p%5D.JPG Drawing the panel for the casewindow. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/10%20%5B550xl3p%5D.JPG And used the grinder to cut it out, also cut a hole in the original panel. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/11%20%5B550xl3p%5D.JPG Cutting the logo in the right size. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/12%20%5B550xl3p%5D.JPG Determining the spot. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/13%20%5B550xl3p%5D.JPG Drawing it on the aluminum. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/14%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/15%20%5B550xl3p%5D.JPG Cutting out the logo with my fully automated lasercutter with built-in footpedal and spotlight. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/16%20%5B550xl3p%5D.JPG Lots of filing and sanding to do afterwards. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/17%20%5B550xl3p%5D.JPG Polished the thin edges so they will shine. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/18%20%5B550xl3p%5D.JPG Glued the alu panel to the original panel. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/19%20%5B550xl3p%5D.JPG Also glued in the acrylic panel. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/20%20%5B550xl3p%5D.JPG Measuring the exact spot of the copper parts. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/21%20%5B550xl3p%5D.JPG Drilling and tapping. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/22%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/23%20%5B550xl3p%5D.JPG Determining the holes to attach the new front panel. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/24%20%5B550xl3p%5D.JPG And again drilling and tapping... http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/25%20%5B550xl3p%5D.JPG Cleaned up 2 out of 3 desks on the attic to move on there :) (As in, all the mess is on the third now) http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/26%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/27%20%5B550xl3p%5D.JPG Shortening the bolts so I won't damage the cpu. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/28%20%5B550xl3p%5D.JPG Can't wait to test it all to see if it actually works. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/29%20%5B550xl3p%5D.JPG Testsetup :) http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/30%20%5B550xl3p%5D.JPG First boot in bios is always exciting .. but looks good. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/31%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/32%20%5B550xl3p%5D.JPG Light stress, 65 degrees max .. works for me. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/33%20%5B550xl3p%5D.JPG Next test, streaming blu-ray for 3 hours. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/34%20%5B550xl3p%5D.JPG Temps were between 40 and 50 degrees. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/35%20%5B550xl3p%5D.JPG With light from the original powerbutton. http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/36%20%5B550xl3p%5D.JPG Next update ... more light :) http://www.l3p.nl/files/Hardware/L3p%20AlCu/4-mod2/37%20%5B550xl3p%5D.JPG Link to comment Share on other sites More sharing options...
L3p Posted January 1, 2013 Author Share Posted January 1, 2013 To start off right .. an update .. and .. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/2013.JPG Let's get rid of all the cables. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/1%20%5B550xl3p%5D.JPG Where to hide them? http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/2%20%5B550xl3p%5D.JPG Connecting the vandal switch. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/3%20%5B550xl3p%5D.JPG Shortening some cables for led and psu. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/4%20%5B550xl3p%5D.JPG Had some Enzotech heatsinks laying around and used them too. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/5%20%5B550xl3p%5D.JPG Testing the ledstrip and vandal switch. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/6%20%5B550xl3p%5D.JPG Psu and all cables :) http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/7%20%5B550xl3p%5D.JPG Gone! http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/8%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/9%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/10%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/11%20%5B550xl3p%5D.JPG Another full test and photos with flasher. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/12%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/13%20%5B550xl3p%5D.JPG And without flasher. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/14%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/15%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/16%20%5B550xl3p%5D.JPG Time to do something about the ssd. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/17%20%5B550xl3p%5D.JPG My idea is to make it a 'bit' shiny. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/18%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/19%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/20%20%5B550xl3p%5D.JPG Almost there. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/21%20%5B550xl3p%5D.JPG And a last shot before it disappears in AlCu. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/22%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/23%20%5B550xl3p%5D.JPG Done. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/24%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/25%20%5B550xl3p%5D.JPG My daughter is extremely happy with it! Daddy's happy too as it's the first time since the new Xbmc he can see the DTS-HD notification on his receiver :) http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/26%20%5B550xl3p%5D.JPG What's left to happen. - Sanding the frontpanel. - adding thermal paste between all the heatpipes and copper side plates - adding a Cooler Master logo. http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/27%20%5B550xl3p%5D.JPG Link to comment Share on other sites More sharing options...
L3p Posted January 14, 2013 Author Share Posted January 14, 2013 Thanks Rodrigo! And another small and last update. First disassembled all copper again. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/1%20%5B550xl3p%5D.JPG To get some thermal paste between it. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/2%20%5B550xl3p%5D.JPG And cleaning it all afterwards. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/3%20%5B550xl3p%5D.JPG Disassembling the front panel. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/4%20%5B550xl3p%5D.JPG To start sanding again. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/5%20%5B550xl3p%5D.JPG Also did something else with the SSD. Wet sanded it with P2000 which gives a non mirroring nice shine. After sawing a Corsair logo into the Cooler Master case .. well thought it would be nice to add a Cooler Master logo somewhere too :) http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/6%20%5B550xl3p%5D.JPG More sanding. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/7%20%5B550xl3p%5D.JPG And even more sanding. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/8%20%5B550xl3p%5D.JPG Finally the result I wanted. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/9%20%5B550xl3p%5D.JPG So assembled it again. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/10%20%5B550xl3p%5D.JPG And a few photos before powering and testing it again. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/11%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/12%20%5B550xl3p%5D.JPG Also a few in daylight. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/13%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/14%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/15%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/16%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/17%20%5B550xl3p%5D.JPG Oops ... wrong wire.. Not even that weird :) (ssd also still not attached) http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/18%20%5B550xl3p%5D.JPG And a final test with temperatures. Idle 40-45 degrees, stressed 70 max. http://www.l3p.nl/files/Hardware/L3p%20AlCu/6-mod4/19%20%5B550xl3p%5D.JPG Link to comment Share on other sites More sharing options...
stratosrally Posted January 15, 2013 Share Posted January 15, 2013 All that hard work really paid off, it is gorgeous! Link to comment Share on other sites More sharing options...
L3p Posted January 15, 2013 Author Share Posted January 15, 2013 Thanks again stratosrally! Hereby the final photos. I have to say, I really liked this small project, a complete different thing.Also very weird to have a running pc making no noise at all ... 0dB. http://www.l3p.nl/files/Hardware/L3p%20AlCu/AlCu2_final.png http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/1%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/2%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/3%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/4%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/5%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/6%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/7%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/8%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/9%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/10%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/11%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/12%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/13%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/14%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/15%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/16%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/17%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/18%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/19%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/5-mod3/11%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/20%20%5B550xl3p%5D.JPG http://www.l3p.nl/files/Hardware/L3p%20AlCu/7-final/21%20%5B550xl3p%5D.JPG I want to thank the following companies for all their support the last 2 years! http://redharbinger.com/photo/Cross/Sponsorlogo/corsair.pnghttp://redharbinger.com/photo/Cross/Sponsorlogo/cm.pnghttp://redharbinger.com/photo/Cross/Sponsorlogo/asus.pnghttp://redharbinger.com/photo/Cross/Sponsorlogo/highflow.png Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.