Do i have High temps with the H50?

[McLareN_F1]

Hi im curious if i have bad/high temps with my H50. My Overclock is i7 920 D0 @ 4.1GHz vCore 1.275. Any comments/suggestions?

 

My H50 Setup is S-FLEX SFF21F->Sound Damper->Rad->Stock H50 Fan->

Case is the 800D with 3 Scythe Slip Stream Kaze Jyuni 120MM Fan 800RPM 40.1CFM exhaust fans

 

My LinX temps are Max 86c

http://img30.imageshack.us/img30/9390/69265741.png

 

23hr blent test

http://img696.imageshack.us/img696/7611/74324675.png

[MaK2000]

I just installed an H50 today in my 800D. I already had a TRUE in push pull which seems to be just as good from the temps that I am getting. I am in push pull on the rad. I replaced the stock fan with two Yate Loon D12SL-124UB. The memory that I have in here right now will not let me reach 4.1 but tomorrow my DOMINATOR GTs are being delivered so I can compare. I see that you have one of the same occurrences I was seeing after installing it. Core 2 and 4 are about 4 degrees lower than cores 1 and 3. I thought it was odd since with my TRUE they were always all the same or within one degree of each other. I have two sets of 2000 C8 coming tomorrow so I will right back with my results. What board do you have? I am running the E758.

[McLareN_F1]

I just installed an H50 today in my 800D. I already had a TRUE in push pull which seems to be just as good from the temps that I am getting. I am in push pull on the rad. I replaced the stock fan with two Yate Loon D12SL-124UB. The memory that I have in here right now will not let me reach 4.1 but tomorrow my DOMINATOR GTs are being delivered so I can compare. I see that you have one of the same occurrences I was seeing after installing it. Core 2 and 4 are about 4 degrees lower than cores 1 and 3. I thought it was odd since with my TRUE they were always all the same or within one degree of each other. I have two sets of 2000 C8 coming tomorrow so I will right back with my results. What board do you have? I am running the E758.

 

E757 X58 SLI LE

 

My Settings:

 

Mother Board ( EVGA X58 LE )

Bios ( 44 )

CPU ( i7 920 D0)

CPU Cooler ( Corsair H50)

Memory ( 6GB Corsair Dominator DDR3-1600 TR3X6G1600C8D )

PSU ( Corsair 750W )

GPU ( ASUS 5850 )

Drivers ( 10.2 )

Operating System ( Windows 7 Ultimate x64 )

 

Frequency Control

CPU Clock Ratio ( 20x )

CPU Host Frequency (Mhz) ( 196 )

MCH Strap ( Auto )

CPU Uncore Frequency (Mhz) ( Auto )

CPU Clock Skew ( 0 ps )

Spread Spectrum ( Disabled )

PCIE Frequency (Mhz) ( 100 )

OC Recorvery ( Enabled )

Turbo Performance (Enabled)

 

Memory Feature

Memory Speed ( Standard )

Memory Control Setting ( Enabled )

Memory Frequency ( 2:8 )

Channel Interleave Setting ( 6 Way )

Rank Interleave Setting ( 4 Way )

Memory Low Gap ( Auto )

tCL Setting ( 8 )

tRCD Setting ( 8 )

tRP Setting ( 8 )

tRAS Setting ( 24 )

tRFC Setting ( 88 )

Command Rate ( 1T )

 

Voltage Control

EVGA VDroop Control ( Without VDroop )

CPU VCore ( 1.275 )

CPU VTT Voltage ( +75 )

CPU PLL VCore ( Auto )

DIMM Voltage ( 1.65 )

DIMM DQ Vref ( +0mV )

QPI PLL VCore ( 1.25 )

IOH VCore ( 1.2 )

IOH/ICH I/O Voltage ( Auto )

ICH VCore ( 1.2 )

 

CPU Feature

Intel SpeedStep ( Disabled )

Turbo Mode Function ( Enabled )

CxE Function ( Disabled )

Execute Disable Bit ( Disabled )

Virtualization Technology ( Disabled )

Intel HT Technology ( Enabled )

Active Processor Cores ( All )

QPI Control Settings ( Enabled )

QPI Link Fast Mode ( Enabled )

QPI Frequency Selection ( 4.800 GT/s )

[MaK2000]

I didn't get my new memory until today. I am having some issues running stable at 4.2 right now. It will boot but isn't running stable enough to pass any tests for any extended time. From what I was seeing while it would run your temps do look higher than mine. I can't really tell until I can get some time to find out what is wrong with mys settings but BFBC2 just launched so I have been playing that.