gamerxs Posted March 13, 2009 Share Posted March 13, 2009 I am trying to get the most out of my TR3X6G1600C8D. The BIOS setting are all default. I just need to know what settings I need to change in the BIOS. I have already seen the thread with the screen shots of the BIOS settings, the closest board is the T3eH6. I need to know what are all the specific settings I need to change. I know the ram says 1.65v at 8-8-8-24. Won't just setting dram bus voltage to 1.65v like recommended throw off the QPI voltage since they need to be in sync, or can the other voltage remain the defaults when dram bus is set to 1.65v. Please tell me the exact settings I need to change. Thanks for any help. Link to comment Share on other sites More sharing options...
Wired Posted March 13, 2009 Share Posted March 13, 2009 Start with the settings on the DFI boards listed here:Intel Core i7 MB Settings By X58 MB Link to comment Share on other sites More sharing options...
gamerxs Posted March 13, 2009 Author Share Posted March 13, 2009 Am I suppose to copy all the setting? or just the ones that are highlighted? Sorry, I am afraid of screwing something up. Thanks. Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted March 16, 2009 Corsair Employees Share Posted March 16, 2009 I would get the latest BIOS version and load setup defaults and try the XMP Profile other wise you will need to set the memory and QPI Voltage manually as well as the timings and frequency. Link to comment Share on other sites More sharing options...
gamerxs Posted March 18, 2009 Author Share Posted March 18, 2009 No XMP profile even with latest BIOS... Link to comment Share on other sites More sharing options...
DerekT Posted March 18, 2009 Share Posted March 18, 2009 Am I suppose to copy all the setting? or just the ones that are highlighted? Sorry, I am afraid of screwing something up. Thanks. Research From DFI Club and a Memory Master http://www.csd.dficlub.org/forum/showthread.php?t=9536 http://i4memory.com/102537-post3.html From your Mainboard's Website: http://www.dfi.com.tw/portal/CM/cmproduct/XX_cmproddetail/XX_WbProdsWindow?itemId=561&downloadFlag=false&action=e&windowstate=normal&mode=view The System Memory configuration Guideline.The System BIOS Setting Guideline.The System BIOS Setting Guideline Version 2. Download Memtest86+ V2.11 from--->Hereand extract the ISO image. Burn the ISO image to an CD-ROM disk. Download CPU-z from Here .Shut the system down. Insert a single stick in the slot 2 (First of the three green slots and closest green slot to the CPU). Restart. Enter the BIOS. Set to these values:Genie BIOS Setting CPU Feature Set VR Current Limit Max: Disabled Thermal Management Control: Enabled EIST Function: Enabled CxE Function: Enabled Execute Disable Bit: Disabled Virtualization Technology: Enabled ***** Logical Processor Setting ***** Intel HT Technology: Disabled Active Processor Cores: All DRAM Timing Memory Control Setting: AUTO Memory LowGap: 1024M DRAM Command Rate: AUTO/1N/2N : 1N CAS Latency Time (tCL): 8 RAS# to CAS# Delay (tRCD): 8 RAS# Precharge (tRP): 8 Precharge Delay (tRAS): 24 REF to ACT Delay (tRFC): AUTO Write to PRE Delay (tWR): AUTO Rank Write to Read (tWTR): AUTO ACT to ACT Delay (tRRD): AUTO Row Cycle Time (tRC): AUTO Read CAS# Precharge (tRTP): AUTO Four ACT WIN Time (tFAW): AUTO Voltage Setting O.C. Shut Down Free: Disable O.C.S.D.F CPU VID Control: Auto CPU VID Special Add Limit: Enabled CPU VID Special Add: Auto Vcore Droop Control: Enabled DRAM Bus Voltage: 1.65 DRAM PWM Switch Frequency: Reduction 15% DRAM PWM Phase Control: 2 Phase Operation CPU VTT Special Add: AUTO CPU VTT Voltage: 1.55 Volt VTT PWM Switch Frequency: Reduction 15% VTT PWM Phase Control: 2 Phase Operation CPU PLL Voltage: 1.80v IOH/ICH 1.1V Voltage: 1.21v IOH Analog Voltage: 1.20v ICH 1.5 Voltage: 1.5v ICH 1.05V Voltage: 1.05v DIMM 1/2 DQ/DQSTB Bus VREF: -00.0% DIMM 3/4 DQ/DQSTB Bus VREF: -00.0% DIMM 5/6 DQ/DQSTB Bus VREF: -00.0% ADDR/CMD VREF Control: Disabled x DIMM 1/2 ADDR/CMD Bus VREF: 110 x DIMM 3/4 ADDR/CMD Bus VREF: 110 x DIMM 5/6 ADDR/CMD Bus VREF: 110 CPU QPI Drive Strength: Normal IOH QPI Drive Strength: Normal Exit Setup Shut down: Mode 2 O.C. Fail Retry Counter: Enabled O.C. Fail CMOS Reload: Disabled PPM Function: Disable Turbo Mode Function: Enabled CPU Non-Turbo Clock Ratio: 20x [b]* BCLK/UCLK/QPI Controller Settings *[/b] QPI Control Settings: Enabled QPI Link Fast Mode: Enabled QPI Frequency: Auto CPU Base Clock (BCLK): 200 Mhz Boot Up CPU Base Clock: AUTO PCIE Clock: 100 Mhz DRAM Frequency: 1600Mhz UnCore Frequency: 1600 CPU Spread Spectrum: Disabled PCIE Spread Spectrum: DisabledSave BIOS and shut down the System. Insert a stick in slot 3 and 6 (Green Slots) and boot to the Memtest Version 2.11 CD and allow for two full passes. Results? Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.