Jump to content
Corsair Community

TW3X2G1600C9DHX and ASUS P5QC


Simo

Recommended Posts

Hi all,

 

i have assembled a new machine for a my customer (so i have not insert any config information on my profile becouse is not my machine) with this configuration:

 

- MB ASUS P5QC

- TECNOWARE Glacier 600W Server

- INTEL Q8200 Quad-Core2

- CORSAIR DDR3 10666 (1600MHz) 2GB(2x1GB) DHX

- SEAGATE Barracuda 1TB SATA2 32MB

- Floppy disk drive 3.5" 1.44

- ASUS Nvidia GF9500GT 512M DDR3

- LG GGW-H20L BlueRay DVD±RW

- ASUS DRW-2014S1 20X DualLayer PATA

- ASUS Triton70 AMD / Intel 0.28 Rca

- MICROSOFT Windows VISTA HomePremium 32-bit

 

The machine freeze in various situation, also when only operating system work without any other program working. I have try to exchange the position of ram or work with only one dimm. But the problem is the same. The machin don't have particular problem or reproducible case for to freeze.. only "random". Someone say to me that for a ddr3 must to set bios setting manually but i have notidea. Can you help me?

 

Thank you,

 

Simone

Link to comment
Share on other sites

Download Memtest86+ V2.10 from--->

Download CPU-z from
.

You have to perform a slight overclock of the CPU FSB to attain the necessary 1:1 ratio of CPU:DRAM. Insert a single stick of DRAM in Slot 2. Restart the system an denter your BIOS. Load Setup Defaults. Save Setup Defaults. Set to these values:

AI Overclock Tweaker

Configure Advanced CPU Settings

CPU Ratio Setting = 7
C1E Support = Enabled

Configure System Performance Settings

Ai OVerclocking Tuner = Manual
CPU Ratio Setting = 7
FSB Frequency = 400
PCIE Frequency = 100
FSB Strap to North Bridge = 333
DRAM Frequency =  DDR3-1600MHz
Dram CLK Skew on Channel A1 = Auto
Dram CLK Skew on Channel A2 = Auto
Dram CLK Skew on Channel B1 = Auto
Dram CLK Skew on Channel B2 = Auto
Dram TIming COntrol =   Manual 

Primary Information

CAS# Latency = 9 DRAM Clocks
DRAM RAS# to CAS #Delay = 9 DRAM Clocks
DRAM RAS# Precharge =  9 DRAM Clocks
DRAM RAS# Activate to Precharge = 24 DRAM Clocks
RAS# to RAS# Delay = Auto
Row Refresh Cycle Time = 60 DRAM Clocks
Write Recovery Time = Auto
Read to Precharge Time = Auto

Secondary Information

Read to Write Delay (S/D) = Auto
Write to Read Delay (S) =  Auto
Write to Read Delay (D) = Auto
Read to Read Delay (S) = Auto
Read to Read Delay (D) = Auto
Write to Write Delay (S) = Auto
Write to Write Delay (D) = Auto

[b]Third Information[/b]

WRITE to PRE delay = Auto
READ to PRE delay = Auto
PRE to PRE delay = Auto
ALL PRE to ACT delay = Auto
ALL PRE to RED Delay = Auto
DRAM Static Read Control =  Disabled
DRAM Dynamic Write Control =  Disabled
DRAM Read Training =  Disabled
DRAM Write Training =  Disabled
MEM. OC Charger  = Enabled
Ai Clock Twister=  Auto
Ai Transaction Booster= Auto

Voltages

CPU Voltage = Auto
CPU GTL Voltage Reference(0/2) = Auto
CPU GTL Voltage Reference(1/3) = Auto
CPU PLL Voltage = Auto
FSB Termination Voltage = Auto
DRAM Voltage = 1.8v
NB Voltage = Auto
NB GTL Reference = Auto
SB Voltage = Auto
PCIE SATA Voltage = Auto

Load-Line Calibration = Disabled
CPU Spread Spectrum = Disabled
PCIE Spread Spectrum = Disabled
CPU Clock Skew = Auto
NB Clock Skew = Auto
CPU Margin Enhancement = Optimized

 

Shut the system down. Insert the second stick in slot 4 and boot to the Memtest CD. Allow for two full passes. Then, if stable, enter Windows and run CPU-z. Post screenshots of CPU-z's CPU, Memory and SPD tabs.

Link to comment
Share on other sites

Hi DerekT,

 

the first thank you very much for your answer.

Then i have maked all that you say and this is the screenshot:

 

CPU.thumb.jpg.6aace317517ce86c57f5c886c3b6a1f6.jpg

MEM.thumb.jpg.455a6c7b49d97553612dbf42e01758a2.jpg

SPD.thumb.jpg.0f5a15a3917c7b782ece72ac1c03ef82.jpg

 

I have only two little problem. In DRAM Frequency = DDR3-1600MHz

i have only DRAM Frequency = DDR3-1601MHz and i have selected this option, and when i have restart the machine i have a error message for "overclocking not succesfull run setup ...." i entered in the bios i seen the the setting are ok and i chose discard (becouse nothing changed) and exit. Then the machin is started.

 

What do you this about?

 

Thank you again,

 

Simo

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...