Jump to content
Corsair Community

TW3X4G1333C9DHX running at 1066?


Snoop786

Recommended Posts

hi i have this ram

TW3X4G1333C9DHX running at 1066 mhz?

my motherboard is Gigabyte EP45C-DS3R

my pc boots up and shows 4gb 1066 not 1333mhz

how can i get it to 1333mhz

 

and also why does my 4870x2 show 1.0 in vista experience score??

 

 

thanks in advance

Link to comment
Share on other sites

hi i have this ram

TW3X4G1333C9DHX running at 1066 mhz?

my motherboard is Gigabyte EP45C-DS3R

my pc boots up and shows 4gb 1066 not 1333mhz

how can i get it to 1333mhz

 

and also why does my 4870x2 show 1.0 in vista experience score??

 

 

thanks in advance

 

For the motherboard, you might need the latest BIOS revision in order to set the correct memory speed. A lot of motherboards ship to you with a BIOS version that's two or three releases behind the current one.

 

As for the low graphics score with your present graphics card, check to see that you have the latest Radeon/Catalyst driver version downloaded from the AMD Web site and then properly installed on your system. (Again, this is because the driver which came on the card's CD-ROM is likely several releases old.) And in order to get a "valid" Windows Experience Index score, be sure to refresh your score (since that 1.0 score was based on you just running the standard Microsoft-provided VGA video driver on your system when it was rated).

Link to comment
Share on other sites

hi

i have the stated motherbaord and ram above

 

I needed your CPU to setup the values manually.

 

Download Memtest86+ V2.01 from--->

Download CPU-z from
.

Enter your BIOS. Load Setup Defaults. Save Setup Defaults. On the main BIOS screen press Ctrl + F1. You will see the screen flicker. Next select the MB Intelligent Tweaker option. On that screen you will see many additional settings that were not there before. Enter these values:

 

 

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster: Auto
CPU Clock Ratio: 8.5
Fine CPU Clock Ratio: 0

Clock Chip Control

Standard Clock Control
CPU Host Clock Control: Enabled
CPU Host Frequency (Mhz): 333
PCI Express Frequency (Mhz): 100
C.I.A.2:[Disabled]

DRAM Performance Control

Performance Enhance: STANDARD
Extreme Memory Profile (X.M.P.): Disabled
(G)MCH Frequency Latch: Auto
System Memory Multiplier: 4.0
Memory Frequency (Mhz): 1333

Standard Timing Control
DRAM Timing Selectable: Manual

CAS Latency Time: 9
tRCD: 9
tRP: 9
tRAS: 24

Advanced Timing Control

tRRD: Auto
tWTR: Auto
tWR: Auto
tRFC: 55
tRTP: Auto
Command Rate (CMD): 2

Motherboard Voltage Control
Voltage Type: Manual

CPU Vcore: Auto
CPU Termination: 1.2v
CPU PLL: 1.5v
CPU Referen: 0.755v (.64% Of Vtt)
CPU Reference2: 0.8v (.67% Of Vtt) 
MCH/ICH: Auto
MCH Core: Auto
MCH Reference: Auto
MCH/DRAM Ref: Auto
ICH I/O: Auto
ICH Core: Auto

DRAM
DRAM Voltage: 1.6v 
DRAM Termination: 0.9v
Channel A Reference: 0.9v
Channel B Reference: 0.9v

Advanced Settings

Limit CPUID Max. to 3: Disabled
No-Execute Memory Protect: Enabled
CPU Enhanced Halt (C1E): Enabled
C2/C2E State Support: Disabled
x C4/C4E State Support: Disabled
CPU Thermal Monitor 2(TM2) : Enabled
CPU EIST Function: Disabled
Virtualization Technology: Enabled

Integrated Peripherals

Legacy USB Storage Detect: Disabled (For Memtest, Enabled after Memtest) 

Run Memtest for two full passes. When assured of stable DRAM, then enter Windows and Run CPU-z and post screenshots of CPU-z's CPU, Memory and SPD tabs.

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...