Jump to content
Corsair Community

Extreme Rampage advice


finalware

Recommended Posts

  • Corsair Employees

Yes and the settings ti try are in that link but the MB you have may not be able to reach these settings depending on the CPU you have.

 

Testing parameters for TWIN3X/XMS3-1800C8D:

TW3X4G1800C8DF Data Sheet

 

Motherboard make and model: ASUS P5K3, P5E3 Premium/Deluxe !

Each pair is tested and packaged together using the following settings:

Advanced

Jumper Free

AI Overclock: Manual

CPU Control: Manual

FSB Frequency: 450 MHz

PCIE Frequency: AUTO

DRAM Frequency: DDR3-1800 MHz

DRAM Command Rate: 2T/2N

DRAM Timings Control: Manual

CAS# Latency:___________8

RAS# to CAS# Delay:______8

RAS# Precharge:__________8

RAS# Activate to Precharge:24

DRAM Static Read Control: Disabled

DRAM Dynamic Write Control: Disabled

CPU Spread Spectrum: Disabled

PCIE Spread Spectrum: Disabled

CPU Voltage:__________Auto

CPU PLL Voltage:_______Auto

DRAM Voltage:_________1.76V

FSB Termination Voltage:_Auto

North Bridge Voltage:____1.71V

All settings not listed should be left at AUTO or BIOS Default

Maximum DDR3 recommended VDIMM: 2.00 Volts

Link to comment
Share on other sites

You have the E(0) revision of that CPU and should be able to make a 450Mhz FSB. But you need to have a good CPU cooler and NOT the stock Intel one.

Download Memtest86+ V2.01 from--->

and extract the ISO image. Burn the ISO image to an CD-ROM disk.

Download CPU-z from
.
Extreme Tweaker

Ai Overclock Tuner: Manual
OC From Memory Level Up: Auto
FSB Frequency: 450
CPU Ratio Setting: 8.5

CPU Configuration

CPU Ratio Setting: 8.5
C1E Support: Disabled
CPU TM Function: Enabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Enabled
Execute Disable Bit: Enabled
Core Multi-Processing: Enabled

CPU Clock Skew: Auto
NB Clock Skew: Auto
FSB Strap to North Bridge: 400
PCIE Frequency: 101
DRAM Frequency: 1800
DRAM Command Rate: 2N
DRAM Timing Control: Manual
CAS# Latency: 8
RAS# to CAS# Delay: 8
RAS# Pre Time: 8
RAS# ACT Time: 24
RAS# To RAS# Delay: Auto
REF Cycle Time: Auto
WRITE Recovery Time: Auto
READ to Pre Time: Auto
READ to WRITE Delay (S/D): Auto
WRITE to READ Delay (S): Auto
WRITE to READ Delay (D): Auto
READ to READ (S): Auto
READ to READ (D): Auto
WRITE to WRITE (S): Auto
WRITE to WRITE (D): Auto
WRITE to PRE Delay: Auto
READ to PRE Delay: Auto
PRE to PRE Delay: Auto
ALL PRE to ACT Delay: Auto
ALL PRE to REF Delay: Auto
DRAM Static Read Control: Disabled
DRAM Dynamic Write Control: Disabled

DRAM Skew Control

DRAM CMD Skew on Channel A: Auto
DRAM CLK Skew on DIMM A1: Auto
DRAM CLK Skew on DIMM A2: Auto
DRAM CTL Skew on DIMM A1: Auto
DRAM CTL Skew on DIMM A2: Auto
DRAM CMD Skew on Channel B: Auto
DRAM CLK Skew on DIMM B1: Auto
DRAM CLK Skew on DIMM B2: Auto
DRAM CTL Skew on DIMM B1: Auto
DRAM CTL Skew on DIMM B2: Auto

Ai Clock Twister: Auto
Ai Transaction Booster: Auto
Common Performance Level: Auto

EPU II Phase Control: On
CPU Voltage: Auto
Load-Line Calibration: Disabled
CPU PLL Voltage: Auto
FSB Termination Voltage: Auto
CPU GTLVerf (0): Extreme Tweaker

Ai Overclock Tuner: Manual
OC From Memory Level Up: Auto
FSB Frequency: 450
CPU Ratio Setting: 8.5

CPU Configuration

CPU Ratio Setting: 09.0
C1E Support: Disabled
CPU TM Function: Enabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Enabled
Execute Disable Bit: Enabled
Core Multi-Processing: Enabled

CPU Clock Skew: Delay 300ps
NB Clock Skew: Delay 200ps
FSB Strap to North Bridge: 400
PCIE Frequency: 101
DRAM Frequency: 1880
DRAM Command Rate: 1N
DRAM Timing Control: Manual
CAS# Latency: 8
RAS# to CAS# Delay: 8
RAS# Pre Time: 8
RAS# ACT Time: 24
RAS# To RAS# Delay: Auto
REF Cycle Time: Auto
WRITE Recovery Time: Auto
READ to Pre Time: Auto
READ to WRITE Delay (S/D): Auto
WRITE to READ Delay (S): Auto
WRITE to READ Delay (D): Auto
READ to READ (S): Auto
READ to READ (D): Auto
WRITE to WRITE (S): Auto
WRITE to WRITE (D): Auto
WRITE to PRE Delay: Auto
READ to PRE Delay: Auto
PRE to PRE Delay: Auto
ALL PRE to ACT Delay: Auto
ALL PRE to REF Delay: Auto
DRAM Static Read Control: Disabled
DRAM Dynamic Write Control: Disabled

DRAM Skew Control

DRAM CMD Skew on Channel A: Auto
DRAM CLK Skew on DIMM A1: Auto
DRAM CLK Skew on DIMM A2: Auto
DRAM CTL Skew on DIMM A1: Auto
DRAM CTL Skew on DIMM A2: Auto
DRAM CMD Skew on Channel B: Auto
DRAM CLK Skew on DIMM B1: Auto
DRAM CLK Skew on DIMM B2: Auto
DRAM CTL Skew on DIMM B1: Auto
DRAM CTL Skew on DIMM B2: Auto

Ai Clock Twister: Auto
Ai Transaction Booster: Auto
Common Performance Level: Auto

EPU II Phase Control: Auto
CPU Voltage: Auto
Load-Line Calibration: Disabled
CPU PLL Voltage: Auto
FSB Termination Voltage: Auto
CPU GTLVerf (0): Extreme Tweaker

Ai Overclock Tuner: Manual
OC From Memory Level Up: Auto
FSB Frequency: 450
CPU Ratio Setting: 8.5

CPU Configuration

CPU Ratio Setting: 09.0
C1E Support: Disabled
CPU TM Function: Enabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Enabled
Execute Disable Bit: Enabled
Core Multi-Processing: Enabled

CPU Clock Skew: Delay 300ps
NB Clock Skew: Delay 200ps
FSB Strap to North Bridge: 400
PCIE Frequency: 101
DRAM Frequency: 1880
DRAM Command Rate: 1N
DRAM Timing Control: Manual
CAS# Latency: 8
RAS# to CAS# Delay: 8
RAS# Pre Time: 8
RAS# ACT Time: 24
RAS# To RAS# Delay: Auto
REF Cycle Time: Auto
WRITE Recovery Time: Auto
READ to Pre Time: Auto
READ to WRITE Delay (S/D): Auto
WRITE to READ Delay (S): Auto
WRITE to READ Delay (D): Auto
READ to READ (S): Auto
READ to READ (D): Auto
WRITE to WRITE (S): Auto
WRITE to WRITE (D): Auto
WRITE to PRE Delay: Auto
READ to PRE Delay: Auto
PRE to PRE Delay: Auto
ALL PRE to ACT Delay: Auto
ALL PRE to REF Delay: Auto
DRAM Static Read Control: Disabled
DRAM Dynamic Write Control: Disabled

DRAM Skew Control

DRAM CMD Skew on Channel A: Auto
DRAM CLK Skew on DIMM A1: Auto
DRAM CLK Skew on DIMM A2: Auto
DRAM CTL Skew on DIMM A1: Auto
DRAM CTL Skew on DIMM A2: Auto
DRAM CMD Skew on Channel B: Auto
DRAM CLK Skew on DIMM B1: Auto
DRAM CLK Skew on DIMM B2: Auto
DRAM CTL Skew on DIMM B1: Auto
DRAM CTL Skew on DIMM B2: Auto


Ai Clock Twister: Auto
Ai Transaction Booster: Auto
Common Performance Level: Auto

EPU II Phase Control: Auto
CPU Voltage: Auto
Load-Line Calibration: Disabled
CPU PLL Voltage: Auto
FSB Termination Voltage: Auto
CPU GTLVerf (0): Auto
CPU GTLVerf (1): Auto
CPU GTLVerf (2): Auto
CPU GTLVerf (3): Auto
NB GTLVerf: Auto
North Bridge Voltage: Auto
DRAM Voltage: 1.80v
NB DDRVref: Auto
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: Auto
South Bridge 1.5 Voltage: Auto
South Bridge 1.05 Voltage: Auto
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU GTLVerf (1): +50mv
CPU GTLVerf (2): +50mv
CPU GTLVerf (3): +50mv
NB GTLVerf: +60mV
North Bridge Voltage: Auto
DRAM Voltage: 1.80
NB DDRVref: Auto
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: Auto
South Bridge 1.5 Voltage: Auto
South Bridge 1.05 Voltage: Auto
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU GTLVerf (1): +50mv
CPU GTLVerf (2): +50mv
CPU GTLVerf (3): +50mv
NB GTLVerf: +60mV
North Bridge Voltage: Auto
DRAM Voltage: 1.80
NB DDRVref: Auto
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: Auto
South Bridge 1.5 Voltage: Auto
South Bridge 1.05 Voltage: Auto
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

Run Memtest for two full passes. When assured of stable DRAM, then enter Windows and Run CPU-z and post screenshots of CPU-z's CPU, Memory and SPD tabs.

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...