Jump to content
Corsair Community

Asus P5Q3 - Memory(?) Problem


silenced

Recommended Posts

Hi,

 

I don't seem to get my computer to work stabely.

Following error might pinpoint it's my RAM.

IMG

 

Since in this case screenshots might say more then typing the info,

this is what i get when i load everything in default; strange thing is that after the first restart it allready crashes.

IMG

 

Setting everything the way i think it should be:

IMG

Gives this:

IMG

 

Ram picture:

IMG

 

Pictures @ http://users.telenet.be/fotoscomputer/images/

Link to comment
Share on other sites

Hey,

thanks for your reply.

Anyways i thougth i mentioned it but apparently i didn't, i tried memtest for a couple of passes (3-4) with all memory sticks plugged in, didn't give any error.

 

Edit: Dno if it is normal but it detects Pentium 3 2500Mhz cpu ?

Link to comment
Share on other sites

Download these programs. They are the newest.

Download CPU-z from
.

Download Real Temp from-->

Enter your BIOS. Load Setup Defaults. Save Setup Defaults. Set to these values:

[b]AI Overclock Tweaker[/b]

[b]Configure System Performance Settings[/b]

Ai OVerclocking Tuner = Manual
CPU Ratio Setting = 7.5
FSB Frequency = 333
PCIE Frequency = 100
FSB Strap to North Bridge = 333
DRAM Frequency =  DDR3-1333MHz
Dram CLK Skew on Channel A1 = Auto
Dram CLK Skew on Channel A2 = Auto
Dram CLK Skew on Channel B1 = Auto
Dram CLK Skew on Channel B2 = Auto
Dram TIming COntrol =   Manual 

[b]Primary Information[/b]

CAS# Latency = 9 DRAM Clocks
DRAM RAS# to CAS #Delay = 9 DRAM Clocks
DRAM RAS# Precharge =  9 DRAM Clocks
DRAM RAS# Activate to Precharge = 24 DRAM Clocks
RAS# to RAS# Delay = Auto
Row Refresh Cycle Time = 60 DRAM Clocks
Write Recovery Time = Auto
Read to Precharge Time = Auto

[b]Secondary Information[/b]

Read to Write Delay (S/D) = Auto
Write to Read Delay (S) =  Auto
Write to Read Delay (D) = Auto
Read to Read Delay (S) = Auto
Read to Read Delay (D) = Auto
Write to Write Delay (S) = Auto
Write to Write Delay (D) = Auto

[b]Third Information[/b]

WRITE to PRE delay = Auto
READ to PRE delay = Auto
PRE to PRE delay = Auto
ALL PRE to ACT delay = Auto
ALL PRE to RED Delay = Auto
DRAM Static Read Control =  Enabled
DRAM Dynamic Write Control =  Disabled
DRAM Read Training =  Disabled
DRAM Write Training =  Disabled
MEM. OC Charger  = ENABLED
Ai Clock Twister=  Auto
Ai Transaction Booster= Auto

[b]Volages[/b]

CPU Voltage = Auto
CPU GTL Voltage Reference(0/2) = Auto
CPU GTL Voltage Reference(1/3) = Auto
CPU PLL Voltage = Auto
FSB Termination Voltage = Auto
DRAM Voltage = 1.7v
NB Voltage = 1.35
NB GTL Reference = Auto
SB Voltage = Auto
PCIE SATA Voltage = Auto
**************************************************
Load-Line Calibration = [Disabled]
CPU Spread Spectrum = [Disabled]
PCIE Spread Spectrum = [Disabled]
CPU Clock Skew = Auto
NB Clock Skew = Auto
CPU Margin Enhancement = Optimized

Boot to the Memtest CD and allow for two full passes. Then, if stable, enter Windows and run CPU-z. Post screenshots of CPU-z's CPU, Memory and SPD tabs. Finally post a screenshot of Real Temp.

Link to comment
Share on other sites

Hey,

 

The problem is that I have a very unstable pc,

It sometimes reboots, program crashes, and i get errors on prime95.

Also program installers with a check sum(at least i think that) give a 'file is corrupt message' when unpacking. I thought at first it was my CPU since if i set the affinity to CPU0&CPU1 it seems to work...

The guys of the computer store told me they were certain it would be my RAM so... :-|

Goin to try the setting u gave me Derekt and i'll let u know the result.

 

Thanks for ur reply's btw

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...