Prisonbreak94 Posted October 17, 2008 Share Posted October 17, 2008 Hi there, I have been experiencing BSoD's for about 3-4 weeks now, I have been searching all over for answers but I haven't been able to solve my problem. Most leads I got so far are pointing towards RAM problems. My bios DRAM frequency is set to ''Auto'' which i found to be 1100MHz (AtiTool says its 1100MHz atm) Do I need to change my ram frequency? can the blue errors be because of this? I have the latest bios update, just FYI. If you wish, I can post my Stop codes, as well. Thanks, Daniel. Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted October 17, 2008 Corsair Employees Share Posted October 17, 2008 What are you running the memory and CPU Frequency at? With this MB the Memory frequency cannot be more than the CPU FSB: IE if you have an X8000 CPU with a 1333 FSB then the memory frequency will have to be set to DDR1333. Link to comment Share on other sites More sharing options...
Prisonbreak94 Posted October 17, 2008 Author Share Posted October 17, 2008 I'll check in a second but I'm quite sure that my CPU fsb frequency is 1333MHz, and my ram is on 1100MHz. Both memtest86 and windows memory diagnostic tool passed like 5 passes without any errors I ran both of them previously. I will download real temp and CPU-z and post screenshots and set the bios to the values you gave me. Thanks, Daniel Link to comment Share on other sites More sharing options...
DerekT Posted October 17, 2008 Share Posted October 17, 2008 Download memtest from--->Here and extract the ISO image. Burn the ISO image to an CD-ROM disk. Download CPU-z from Here . Download Real Temp from--> HereEnter your BIOS. Load Setup Defaults. Save Setup Defaults. Set to these values: [b]AI Overclock Tweaker[/b] [indent][b]Configure Advanced CPU Settings[/b] CPU Ratio Setting = 10 C1E Support = Enabled [b]Configure System Performance Settings[/b] Ai OVerclocking Tuner = Manual CPU Ratio Setting = 10 FSB Frequency = 333 PCIE Frequency = 100 FSB Strap to North Bridge = 333 DRAM Frequency = 1333 Dram CLK Skew on Channel A1 = Auto Dram CLK Skew on Channel A2 = Auto Dram CLK Skew on Channel B1 = Auto Dram CLK Skew on Channel B2 = Auto Dram TIming COntrol = Manual [b]Primary Information[/b] CAS# Latency = 9 DRAM RAS# to CAS #Delay = 9 DRAM RAS# Precharge = 9 DRAM RAS# Activate to Precharge = 24 RAS# to RAS# Delay = Auto Row Refresh Cycle Time = 52 Write Recovery Time = Auto Read to Precharge Time = Auto [b]Secondary Information[/b] Read to Write Delay (S/D) = Auto Write to Read Delay (S) = Auto Write to Read Delay (D) = Auto Read to Read Delay (S) = Auto Read to Read Delay (D) = Auto Write to Write Delay (S) = Auto Write to Write Delay (D) = Auto [b]Third Information[/b] WRITE to PRE delay = Auto READ to PRE delay = Auto PRE to PRE delay = Auto ALL PRE to ACT delay = Auto ALL PRE to RED Delay = Auto DRAM Static Read Control = Enabled DRAM Dynamic Write Control = Disabled DRAM Read Training = Disabled DRAM Write Training = Disabled MEM. OC Charger = ENABLED Ai Clock Twister= Auto Ai Transaction Booster= Auto [b]Volages[/b] CPU Voltage = Auto CPU GTL Voltage Reference(0/2) = Auto CPU GTL Voltage Reference(1/3) = Auto CPU PLL Voltage = Auto FSB Termination Voltage = Auto DRAM Voltage = 1.8v NB Voltage = 1.28 NB GTL Reference = Auto SB Voltage = Auto PCIE SATA Voltage = Auto ************************************************** Load-Line Calibration = [Disabled] CPU Spread Spectrum = [Disabled] PCIE Spread Spectrum = [Disabled] CPU Clock Skew = Auto NB Clock Skew = Auto CPU Margin Enhancement = Optimized [/indent] Boot to the Memtest CD and allow for two full passes. Then, if stable, enter Windows and run CPU-z. Post screenshots of CPU-z's CPU, Memory and SPD tabs. Finally post a screenshot of Real Temp. Link to comment Share on other sites More sharing options...
Prisonbreak94 Posted October 17, 2008 Author Share Posted October 17, 2008 As I am new to forums, I'm not really sure how to post screenshots... I just uploaded them as attachments...Sorry that I'm a bit of a newb:) Please let me know if these current screenshots give you an insight of a problem that might be causing the blue screens. If so can you please give me some possible solutions. I will also do the bios settings. But just let me know how these look. Thanks, Danny Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted October 17, 2008 Corsair Employees Share Posted October 17, 2008 Can you tell me the bios settings you have set for both CPU and memory and any performance settings that you may have set? Link to comment Share on other sites More sharing options...
DerekT Posted October 17, 2008 Share Posted October 17, 2008 After you have set the bios settings. Boot to the memtest CD and allow for two full passes. If you pass, and if you still are blue-screening, then I advise you to now reinstall the OS as you may have data corruption from prior events. Link to comment Share on other sites More sharing options...
Prisonbreak94 Posted October 17, 2008 Author Share Posted October 17, 2008 Alright - Ram Guy i will let you know the values you want. Right after that, I will put in the values you have suggested, Derek, and let you know how that goes. Give me 15 mins. Link to comment Share on other sites More sharing options...
Prisonbreak94 Posted October 17, 2008 Author Share Posted October 17, 2008 BTW - Derek, I've already tried reinstalling OS, didnt solve anything. I'll run memtest after I give Ram Guy the values he wants and after I set the values you gave me, but its late here in turkey so i'll leave the memtest overnight and post back my results tomorrow morning. Thanks PS: Ram Guy, hold on for CPU + memory bios settings Btw, I didn't set these, they were set at the company that I got this machine built, i never modified them. Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted October 17, 2008 Corsair Employees Share Posted October 17, 2008 With that CPU you would have to set the memory frequency at DDR1333 and why we are asking for the settings that are set. Link to comment Share on other sites More sharing options...
Prisonbreak94 Posted October 17, 2008 Author Share Posted October 17, 2008 Here are some of the settings that I did not ever alter: CPU Ratio Setting: Auto C1E Support= Enabled Max CPUID Value Limit = Disabled Intel Virtualisation Technology = Enabled CPU TM Function = Enabled Execute Disable Bit = Enabled Intel SpeedStep Tech = Enabled All dram settings are set to auto...I don't know what the frequency for the ram is at auto but AtiTool says its currently 1100MHz, I'll set the BIOS Settings that Derek has just suggested now, and run Memtest86 overnight and let you know the results. Good night, see you tomorrow and thanks for all the help so far. Cheers, Daniel Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted October 17, 2008 Corsair Employees Share Posted October 17, 2008 NP But please make sure you disable legacy USB when running http://www.memtest.org. And please do let us know! Link to comment Share on other sites More sharing options...
Prisonbreak94 Posted October 18, 2008 Author Share Posted October 18, 2008 Hello again, Memtest is clean, 5 passes, no errors. 2 more things...after setting up the BIOS info that Derek gave me, PC worked alright, but this morning, when I first tried to turn on the pc, it said overclock failed and told me to either change the BIOS settings or load to default. So I chose change bios settings and did nothing and just left the bios. Now the pc works fine, but this might come up in the future again to bug me. Another thing is, before windows begins loading, I always get black screen with Marvell something BIOS version bla bla... and it writes No hard disk detected! for a moment, then loads windows and all is fine. Any ideas of what I can do next? Do you think setting the ram frequency at 1333MHz might have solved my problem? Thanks, Daniel Link to comment Share on other sites More sharing options...
DerekT Posted October 18, 2008 Share Posted October 18, 2008 That can happen with an inelegant shutdown. There are no overclock settings that I gave you, just default system settings. When it does happen, you did exactly the right thing. If it continues to happen, then there is very likely something in the shutdown sequence that is giving an error and I would do a fresh install and then make an image of that install now that there are no more blue screens. If you can make that issue repeat, then go to the run command and type in msconfig. Choose Diagnostic startup and see if you can make the issue repeat with this startup. If it doesn't occur, then go to msconfig and choose the startup tab. Uncheck the items one by one until the issue doesn't repeat. You can isolate the issue if it is either a resident or terminate and stay resident program. Any ideas of what I can do next? Do you think setting the ram frequency at 1333MHz might have solved my problem? Yes, you needed to drop the DRAM speed and raise the Northbridge voltage a bit when you populate with four DRAM slots. Another thing is, before windows begins loading, I always get black screen with Marvell something BIOS version bla bla... and it writes No hard disk detected! for a moment, then loads windows and all is fine. The "No Hard Disk Detected" is the onboard PATA bridge chip. You can enter your BIOS. Find the Onboard Devices Configuration Page and you will notice "Marvell IDE" and "Marvel IDE Boot ROM". Disable both. They are for the older PATA IDE drives and you must have none since there are no drives detected. This will also speed up your boot and there will be no wait for enumeration of PATA drives. Link to comment Share on other sites More sharing options...
Prisonbreak94 Posted October 19, 2008 Author Share Posted October 19, 2008 Wow, thanks RamGuy and Derek! I think my problem is solved now, thank you very very much. One more thing though, derek. You know you gave me those bios settings, well the AI Overclock Tuner once I set that, my six engine software did not work after that. Six Engine is a software that comes with my mobo i think, and its great because it puts my system in low setting to save more energy when im performing minimal tasks and puts it into high setting when I am playing games and so on. After I put AI Overclock Tuner to manual as you instructed me to, this software was always on high setting and did not open so that I can change setting, it said ''Six Engine can not work with these overclock settings'' or something like that. So I turned AI Overclock Tuner back to Auto again, and six engine works, saving me energy and money. Will having ai o/c tuner on auto make any difference? Thanks, Daniel Link to comment Share on other sites More sharing options...
DerekT Posted October 19, 2008 Share Posted October 19, 2008 If you are stable then you have no worries. I do not like the software myself and yes, there will be issues if you try and run both since the software needs to make on the fly changes and the settings being manually set do not allow for this characteristic. In the final analysis, if your system is stable, then you have no worry. I find that the software is problematic and leads to system instabilities. To be certain, use the Intel Linpack CPU/Memory test. http://67.90.82.13/forums/showthread.php?t=197835 Download Realtemp from Here Run Linpack for full memory (1) and use a 5 pass iteration. Run Real Temp and watch the temperatures. Let the Linpack program run for the full 5 passes. The output in the screen will give you five sets of values. They should be identical for a stable CPU and DRAM. Be sure to turn off your screensavers, display settings that turn the monitor off for this test. Link to comment Share on other sites More sharing options...
007bont Posted October 19, 2008 Share Posted October 19, 2008 thats a nice program, ty for the link Derek! Link to comment Share on other sites More sharing options...
DerekT Posted October 19, 2008 Share Posted October 19, 2008 thats a nice program, ty for the link Derek! Sure thing. Linpack is the best CPU/Memory stability testing program I have used. It is also quick in comparison to Prime95. Link to comment Share on other sites More sharing options...
Prisonbreak94 Posted October 20, 2008 Author Share Posted October 20, 2008 Are you sure I should use this? Linpack by Intel® is an extremely stressful program that will put even the most powerful X86/X64 CPU in the world at its knees. Load temp under Linpack will be up to 22*C higher than the competing software Prime95. This program will make usage of Linpack easier and more practical. Keep in mind, use this program at your own risk. By using this program, you agree that neither I nor Intel shall be responsible for including, but not limited to: burned up CPU, fried motherboard, spontaneous room temperature increase, hair loss, or mental stress. I don't want to mess anything up... Link to comment Share on other sites More sharing options...
007bont Posted October 20, 2008 Share Posted October 20, 2008 I don't want to mess anything up... bare in mind that it is the purpose of any stress program to create a lot of load on the cpu and ram, resulting in heat. but its the only way to test for stability. I tried that program myself yesterday and realised i had to adjust certain things as the cpu reached 76 degrees :D: that were realtemp comes in, you will need to watch it to make sure it doesnt get to hot. (keep in mind that with the settings Derek gave you, the change of getting the smoke out of components is very tiny) and if you recon it becomes to hot (71 degrees or more, just terminate the programm! Link to comment Share on other sites More sharing options...
Prisonbreak94 Posted October 20, 2008 Author Share Posted October 20, 2008 Alright, one more question, how long does 5 passes take, and will I be able to do other stuff while the test is running? thanks, Daniel Link to comment Share on other sites More sharing options...
007bont Posted October 20, 2008 Share Posted October 20, 2008 took me about 10 minutes and yes i could do other stuff, but that depends on the cpu. Link to comment Share on other sites More sharing options...
Prisonbreak94 Posted October 20, 2008 Author Share Posted October 20, 2008 Great. I'm running it right now its around 55-61 C. Erm, one more thing though, I chose 5 passes for (1) Maximum stress, but it told me it could not continue because there was not enough memory. So I pressed (2) Half stress...why can't I do maximum stress? I have 4GB ram.... Link to comment Share on other sites More sharing options...
Prisonbreak94 Posted October 20, 2008 Author Share Posted October 20, 2008 Testing complete, all values are equal but as I said in my previous post I want to do maximum test, how can I do this it says not enough memory... I have 4GB xp only sees 3.2GB right now... But still this should be enough no? Link to comment Share on other sites More sharing options...
007bont Posted October 20, 2008 Share Posted October 20, 2008 try to enable PAE could be that your OS is preventing the program to use large amounts of ram. (also make sure that memory remapping in on, in the bios) Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.