Chrisjuh Posted September 22, 2008 Share Posted September 22, 2008 Hello Ram Guy, I have trouble running my TWIN3X4096-1600C7DHXIN G at 1600mhz on a rampage extreme. If I change the settings to 7-7-7-20 1.9v, my mobo won't even start up. I need to reset to default. Bios v0501 settings: Ai Overclock Tuner = Manual eXtreme Memory Profile = Disabled (Can not be enabled) CPU Ratio Setting = 9 FSB Strap to Northbridge = 400 FSB = 400 DRAM Timing Control = Manual DRAM Frequency = DDR3-1600 DRAM Command Rate = 2N DRAM CLK Skew on Channel A = Auto DRAM CLK Skew on Channel B = Auto DRAM Timing Control = Manual CAS# Latency = 9 RAS# to CAS# Delay = 9 RAS# PRE Time = 9 RAS# ACT Time = 24 All Else to Auto DRAM Static Read Control = disabled DRAM Dynamic Write Control = disabled Ai Clock Twister = Auto Transaction Booster = disabled CPU Voltage = 1.4v CPU PLL Voltage = Auto FSB Termination Voltage = Auto DRAM Voltage = Auto NB Voltage = Auto SB Voltage = Auto Clock Over-Charging Voltage = Auto Load Line Calibration = Auto CPU GTL Voltage Reference = Auto NB GTL Voltage Reference = Auto CPU Spread Spectrum = Disabled PCIE Spread Spectrum = Disabled Please help. Thanks Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted September 22, 2008 Corsair Employees Share Posted September 22, 2008 Your settings looks good, but I would suggest testing the modules one at at time in the slot furthest from the CPU. If both modules fail on their own, then I would drop the CPU ratio to 7x and retest, just to make sure the CPU isn't holding you back. Let us know your results! Link to comment Share on other sites More sharing options...
Chrisjuh Posted September 22, 2008 Author Share Posted September 22, 2008 Okey, I will test it. But why is my eXtreme Memory Profile disabled? Thanks Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted September 22, 2008 Corsair Employees Share Posted September 22, 2008 If you want to use the XMP, then you will need to set AI Overclocking to "XMP" and then you should be able to select the proper profile. Link to comment Share on other sites More sharing options...
Chrisjuh Posted September 22, 2008 Author Share Posted September 22, 2008 Well thats the problem. If I set AI Overclocking to "XMP", I can't select a profile. Its greyed out (disabled) I'm having the same issue as this user http://www.asktheramguy.com/v3/showthread.php?t=71034&highlight=xmp Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted September 23, 2008 Corsair Employees Share Posted September 23, 2008 The modules you have do not have the XMP Profiles on the modules SPD, if the modules label says they are indeed the "IN" part then we can get them replaced if you like but the settings can be set manually if you do not want to go through that. Let's get them replaced, please use the On Line RMA Request Form and we will be happy to replace them. Link to comment Share on other sites More sharing options...
Chrisjuh Posted September 23, 2008 Author Share Posted September 23, 2008 Okey. I will leave it like this. I also run memtest without any errors on both modules. Thanks for your help. Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted September 23, 2008 Corsair Employees Share Posted September 23, 2008 NP Please let me know how you make out! Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.