Jump to content
Corsair Community

CM2X1024-8500C5D on Striker Extreme


Recommended Posts

Hi everyone,

 

I got CM2X1024-8500C5D memory sticks on my striker extreme with q6600 G0 cpu and i would like to hit 3.6 but the problem is i need to use fsb 1800 for 3.6 and therefore i would like the mem to run at 900 mhz (1:1). Unfortunately i have not been lucky with the settings no matter what i try. i tried 5-5-5-15-2T 2.1&2.2V could not boot into windows, tried to loosen timings no luck also tried to raise mem voltage the system would not post.

 

could anyone help me to find the settings for the mem to run at 900 mhz. stable

 

helps appreciated in advance...

Link to comment
Share on other sites

Download memtest from--->
and extract the ISO image. Burn the ISO image to an CD-ROM disk

Download CPU-z from

Download Core Temp-->

Shut your system down and set your DRAM to Slot 2 and Slot 4. Restart.

 

Enter your BIOS and set to these values.

  • Multiplier = 9
  • FSB = 400
  • DRAM = Unlinked and set to 1066Mhz

 

Memory Timing

 

FSB - Memory Clock Mode: Unlinked

CPU FSB: 400

CPU Multi: 9

DDR FSB: 1066

tCL: 5

tRCD: 5

tRP: 5

tRAS: 15

Advanced Memory Settings

tRRD: 5

tRC: 24

tWR: 6

tWTR: 8

tREF: AUTO

tRD: 7

tRFC: 42

Async Latency: AUTO

CMD: 2T

CPU Spread Spectrum: Disabled

PCIE Spread Spectrum: Disabled

MCP PCIE Spread Spectrum: Disabled

SATA Spread Spectrum: Disabled

LDT Spread Spectrum: Disabled

 

CPU Internal Thermal Control: Enabled

Limit CPUID MaxVal: Enabled

Enhanced C1 (C1E): Enabled

Execute Disable Bit: Enabled

Virtualization Technology: Enabled

Enhanced Intel Speedstep Tech: Enabled

LDT Frequency: 5x

 

PCIEX16_1 Frequency (Mhz): 101

PCIEX16_2 Frequency (Mhz): 101

PCIEX16_3 Frequency (Mhz): 101

SPP<->MCP Ref Clock, Mhz: Auto

 

Voltages

 

Vcore = 1.45

Vdimm (DRAM Voltage) = 2.1v

Termination Voltage = 1.4v

1.2v HT: 1.3v

NB Vcore: 1.45v

SB Vcore: 1.50v

CPU VTT: 1.25v

 

Boot to the Memtest CD. Allow for two full passes. If you pass Memtest, enter Windows and post screenshots of your CoreTemp, CPU-z - CPU/Memory/SPD tabs.

Link to comment
Share on other sites

there is a well known fsb hole in the striker at 400 mhz. i use 450x8 for 3.6 ghz. i will post my unstable bios settings when i get home from work for you to have a better idea of my situation

 

thanks for the support btw :):

Link to comment
Share on other sites

there is a well known fsb hole in the striker at 400 mhz. i use 450x8 for 3.6 ghz. i will post my unstable bios settings when i get home from work for you to have a better idea of my situation

 

thanks for the support btw :):

 

There's more than a hole at 400Mhz :) There's quite a few holes with 680i and certainly with Striker. I found quite a few between 333 and 400.

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...