AZUltraRich Posted February 1, 2008 Share Posted February 1, 2008 How can I find the Dominator Qualifications and Testing setting for P5N32-E SLI 680I MOBO With TWIN2X2048-8500C5D version 2.x. I have it set at DDR 800 5,5,5,15-22 2T.<< GOOD If I set it to DDR 1066 CPU-Z " STOP'S " It's not stable :eek: If i back it down say DDR 950 All Good at 1000 CPU-Z STOP'S in under 2 Min or so . Link to comment Share on other sites More sharing options...
Yellowbeard Posted February 1, 2008 Share Posted February 1, 2008 What voltage are you using for the memory? Can you list all your bios settings you have made for voltages, CPU, and memory. Link to comment Share on other sites More sharing options...
AZUltraRich Posted February 1, 2008 Author Share Posted February 1, 2008 AI Tuning: Manual Nvidia GPU Ex: Disabled FSB - Memory Clock Mode: Unlinked FSB (QDR), Mhz: 1600 MEM (DDR), Mhz: 800 Multiplier x 9 Vcore Voltage:1.4 Memory Voltage: 2.1 1.2v HT Voltage:1.3 NB Core Voltage:1.4 SB Core Voltage:1.5 CPU VTT Voltage:1.55 tCL (CAS Latency): 5 tRCD: 5 tRP: 5 tRAS: 15 Command Per Clock (2T) Advance Memory Settings tRRD: AUTO tRC: AUTO tWR: AUTO tWTR: AUTO tREF: AUTO tRD: AUTO tRFC: AUTO Async Latency: AUTO CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled MCP PCIE Spread Spectrum: Disabled SATA Spread Spectrum: Disabled LDT Spread Spectrum: Disabled CPU Internal Thermal Control: Disabled Limit CPUID MaxVal: Disabled Enhanced C1 (C1E): Disabled Execute Disable Bit: Disabled Virtualization Technology: Disabled Enhanced Intel Speedstep Tech: Disabled LDT Frequency: 5x PCIEX16_1 Frequency (Mhz): 100 PCIEX16_2 Frequency (Mhz): 100 PCIEX16_3 Frequency (Mhz): 100 SPP<->MCP Ref Clock, Mhz: 200 Link to comment Share on other sites More sharing options...
Yellowbeard Posted February 1, 2008 Share Posted February 1, 2008 Your Vcore actually looks a bit low for that OC. I'd suggest: Vcore Voltage:1.45 Memory Voltage: 2.2 1.2v HT Voltage:1.3 NB Core Voltage:1.4 SB Core Voltage:1.5 CPU VTT Voltage:1.55 If it is still unstable, try bumping those in red up 1 more notch. Link to comment Share on other sites More sharing options...
AZUltraRich Posted February 1, 2008 Author Share Posted February 1, 2008 Hi, I Set it up that way. On CPU-Z Memory tab I'm at 533, FSB:Dram 3:4, 5,5,5,15 The TRC 30 2T Link to comment Share on other sites More sharing options...
AZUltraRich Posted February 1, 2008 Author Share Posted February 1, 2008 Hi,i just ran the Stress Prime 2004 and it stop. Test 1, 4000 Lucas-Lehmer iterations of M19922945 using 1024K FFT length. FATAL ERROR: Rounding was 0.5, expected less than 0.4 Hardware failure detected, consult stress.txt file. Torture Test ran 0 minutes 58 seconds - 1 errors, 0 warnings. Execution halted. Link to comment Share on other sites More sharing options...
Yellowbeard Posted February 1, 2008 Share Posted February 1, 2008 Try running the CPU and memory in UNLINKED mode. Set each manually to the correct speeds using the voltages you already have set. Link to comment Share on other sites More sharing options...
AZUltraRich Posted February 1, 2008 Author Share Posted February 1, 2008 CPU and memory is UNLINKED . I can run at DDR950 but not at DDR1066 . Do I need to mess with the Advance Memory Settings at all? Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.